Sony STR-DA3500ES Service Manual ▷ View online
STR-DA3500ES
8
2-6. BACK PANEL BLOCK
2-7. VIDEO BOARD
(US, Canadian)
(AEP, UK)
2 AC inlet connector
(CNP51)
1 Cut the clamp.
7 seven screws
(BVTP3
u 8)
7 seven screws
(BVTP3
u 8)
7 screw (BVTP3 u 8)
7 seven screws
(BVTP3
u 8)
7 eight screws
(BVTP3
u 8)
6 two screws
(BV/ring)
9 back panel block
3 three connectors
(CN1501, CN1502, CN1503)
8 screw
(BVTT3
u 6)
Note: In reassembling, use new clamp to
fasten the clamp same as before.
4 Cut the clamp.
5 screw
(BVTP3
u 8)
1 two connectors
(CN6204,
CN6501)
5 connector
(CN6203)
2 connector
(CN1912)
6 VIDEO board
3 screw
(BVTT4
u 8)
4 video bracket block
(US, Canadian)
STR-DA3500ES
9
2-8. MICON BOARD, DIGITAL BOARD
2-9. ACLASS BOARD
Note: In reassembling, use new clamp to
fasten the clamp same as before.
3 six connectors
(CN2030, CN2031, CN2032,
CN2230, CN2231, CN2232)
5 two connectors
(CN2010,
CN2023)
7 four screws
(BVTP2.
6)
qa screw
(BVTP3
u 8)
4 MICON DIGITAL CONN board
1 Cut the clamp.
6 MICON
board
8 connector
(CN5001)
q; connector
(CN2208)
2 three connectors
(CN2015, CN2016, CN2017)
qs two connectors
(CN2217,
CN2218)
9 DSP board
qd DIGITAL board
1 two screws
(BVTP3
u 8)
3 two screws
(BVTP3
u 8)
6 screw (BVTP3 u 8)
6 screw (BVTP3 u 8)
5 connector
(CN1909)
7 four connectors
(CN411, CN511, CN611, CN711)
2 A-CLASS SUPPORT A board
4 A-CLASS SUPPORT B board
8 ACLASS board
(US, Canadian)
STR-DA3500ES
10
2-10. MAIN BLOCK
2-11. MAIN BOARD
Note: This illustration sees the MAIN board from pin jack side.
5 screw
(BVTT4
u 8)
7 two screws
(BVTP3
u 8)
8 two screws
(BVTP3
u 8)
8 two screws
(BVTP3
u 8)
6 bracket (video PWB)
3 connector
(CN1401)
4 connector
(CNP54)
2 two connectors
(CN811,
CN801)
9 main block
Note: In reassembling, use new clamp to
fasten the clamp same as before.
1 Cut the clamp.
1 Cut the clamp.
1 Cut the two clamps.
(US, Canadian)
2 two screws
(BVTP3
u 8)
1 Remove the forty-two solders.
4 MAIN board
3 heat sink block
STR-DA3500ES
11
SECTION 3
TEST MODE
TUNER AM STEP CHANGE MODE
(US and Canadian models)
Either the 9 kHz step or 10 kHz step can be selected for the AM
channel step.
Procedure:
1. Press the [POWER] button to turn on the main power.
2. Turn the [INPUT SELECTOR] dial to select the “AM TUN-
(US and Canadian models)
Either the 9 kHz step or 10 kHz step can be selected for the AM
channel step.
Procedure:
1. Press the [POWER] button to turn on the main power.
2. Turn the [INPUT SELECTOR] dial to select the “AM TUN-
ER”.
3. Press the [POWER] button to turn off the main power.
4. While pressing the [TUNING MODE] button, press the
4. While pressing the [TUNING MODE] button, press the
[POWER] button to turn on the main power.
5. Either the message “AM 9k Step” or “AM10k Step” appears,
select the desired step.
SOUND FIELD CLEAR MODE
The preset sound fi eld is cleared when this mode is activated. Use
this mode before returning the product to clients upon completion
of repair.
Procedure:
1. While pressing the [MUSIC] button, press the [POWER] but-
The preset sound fi eld is cleared when this mode is activated. Use
this mode before returning the product to clients upon completion
of repair.
Procedure:
1. While pressing the [MUSIC] button, press the [POWER] but-
ton to turn on the main power.
2. The message “S.F. CLEAR” appears and initialization is per-
formed.
INITIALIZE MODE
All preset contents are cleared when this mode is activated. Use
this mode before returning the product to clients upon completion
of repair.
Procedure:
1. While pressing the [TONE MODE] and [2CH/A.DIRECT]
All preset contents are cleared when this mode is activated. Use
this mode before returning the product to clients upon completion
of repair.
Procedure:
1. While pressing the [TONE MODE] and [2CH/A.DIRECT]
buttons, press the [POWER] button to turn on the main power.
2. The message “CLEARING” appears and the memories are re-
set to the default values.
3. When done, the message “CLEARED !” appears.
FLUORESCENT INDICATOR TUBE DISPLAY TEST
All fl uorescent segments are tested. When this test is activated, all
segments turn on at the same time, then each segment turns on one
after another.
Procedure:
1. While pressing the [TONE MODE] and [A.F.D.] buttons,
All fl uorescent segments are tested. When this test is activated, all
segments turn on at the same time, then each segment turns on one
after another.
Procedure:
1. While pressing the [TONE MODE] and [A.F.D.] buttons,
press the [POWER] button to turn on the main power.
2. All segments and all LEDs turn on.
SWAP MODE
The signal will be swap to all channel so that all speaker will have
sound output.
Procedure:
1. While pressing the [MEMORY/ENTER] and [2CH/A.
The signal will be swap to all channel so that all speaker will have
sound output.
Procedure:
1. While pressing the [MEMORY/ENTER] and [2CH/A.
DIRECT] buttons, press the [POWER] button to turn on the
main power.
main power.
2. The message “SWAP MODE” appears (No change while dis-
played).
SOUND FIELD LOCK ON/OFF CHANGE MODE
All buttons operation on/off of the front panel is changed.
Procedure:
1. While pressing the [SPEAKERS (OFF/A/B/A+B)] and
All buttons operation on/off of the front panel is changed.
Procedure:
1. While pressing the [SPEAKERS (OFF/A/B/A+B)] and
[MUSIC] buttons, press the [POWER] button to turn on the
main power.
main power.
2. Either the message “S.F. LOCK OFF” or “S.F. LOCK ON”
appears.
COMMAND MODE CHANGE MODE
The command mode of the remote-commander which this set re-
ceives can be changed.
Procedure:
1. While pressing the [2CH/A. DIRECT] button, press the
The command mode of the remote-commander which this set re-
ceives can be changed.
Procedure:
1. While pressing the [2CH/A. DIRECT] button, press the
[POWER] button to turn on the main power.
2. Either the message “C. MODE AV1” or “C. MODE AV2” ap-
pears. Select the desired mode.
XM FACTORY TEST MODE (US and Canadian models)
Mode to confi rm operation of XM. Doing display of ID of XM
antenna and output of audio signal that XM antenna generates, it is
confi rmed that there are no problems in the communication of the
XM antenna and the transmission of the audio signal.
Procedure:
1. The XM antenna was connected, while pressing the [TUNING
Mode to confi rm operation of XM. Doing display of ID of XM
antenna and output of audio signal that XM antenna generates, it is
confi rmed that there are no problems in the communication of the
XM antenna and the transmission of the audio signal.
Procedure:
1. The XM antenna was connected, while pressing the [TUNING
MODE] and [MOVIE] buttons, press the [POWER] button to
turn on the main power.
turn on the main power.
2. Whenever the [DISPLAY] button is pressed, the output of the
audio signal of 1 kHz L/R, 20 Hz L/R, 5 kHz L/R, muting, 1
kHz L and 1 kHz R are switched.
kHz L and 1 kHz R are switched.
SIRIUS FACTORY TEST MODE
(US and Canadian models)
Mode to confi rm operation of SIRIUS. Doing display of ID of
SIRIUS antenna and output of audio signal that SIRIUS antenna
generates, it is confi rmed that there are no problems in the commu-
nication of the SIRIUS antenna and the transmission of the audio
signal.
Procedure:
1. The SIRIUS antenna was connected, while pressing the
(US and Canadian models)
Mode to confi rm operation of SIRIUS. Doing display of ID of
SIRIUS antenna and output of audio signal that SIRIUS antenna
generates, it is confi rmed that there are no problems in the commu-
nication of the SIRIUS antenna and the transmission of the audio
signal.
Procedure:
1. The SIRIUS antenna was connected, while pressing the
[TUNING MODE] and [A.F.D.] buttons, press the [POWER]
button to turn on the main power.
button to turn on the main power.
2. Whenever the [DISPLAY] button is pressed, the output of the
audio signal of 1 kHz L/R, 20 Hz L/R, 10 kHz L/R, noise L,
noise R and stop tone are switched.
noise R and stop tone are switched.
Click on the first or last page to see other STR-DA3500ES service manuals if exist.