Sony SS-NA8ES Service Manual ▷ View online
SS-NA8ES
9
2-7. LOUDSPEAKER (13 cm) (WOOFER: RIGHT SIDE) (SP2)
1
3
2
4
loudspeaker terminal
position
position
Note 3: Check that the caulking portion of a terminal is outside suitable.
:LUHVHWWLQJ
loudspeaker (13 cm) (woofer: right side)
(SP2) “–” terminal
(SP2) “–” terminal
loudspeaker (13 cm) (woofer: right side)
(SP2) “+” terminal
(SP2) “+” terminal
caulking portion
WO board
“W2–” wire (green/black)
“W2–” wire (green/black)
WO board
“W2+” wire (green/)
“W2+” wire (green/)
–)URQWULJKWVLGHYLHZ–
–)URQWULJKWVLGHYLHZ–
tweeter part
3 terminal
(green/black)
3 terminal (green)
Note 4: When installing screws (4 × 25),
follow the installing procedure in
the numerical order given.
tightening torque :
. . 1m
Note 2: Do not touch the central part of the loudspeaker
(13 cm) (woofer: right side) (SP2).
1 four screws
(4
u 25)
2 Pull out the loudspeaker (13 cm) (woofer: right side) (SP2).
4 packing (13 cm)
Note
5: When installing the packing (13 cm), a glossy
surface is made into the speaker cabinet side,
and a rough side is made into the loudspeaker
side, and align the position of the tapped hole
of packing (13 cm) and speaker cabinet.
5 loudspeaker (13 cm) (woofer: right side) (SP2)
Note
8: Be careful not to attach a crack to a speaker cabinet using
the terminal of a wire.
Note
9: Be careful not to put a wire.
Note
10: Check that the connection mistake or insertion of a wire are
not
imperfect.
Note
11: Insert the terminal straightly.
Note
12: After terminal insertion, should check acting as lock of the
terminal
completely.
Note
13: Be careful not to attach a crack to the edge of a speaker cabinet.
Note
14: Check packing (13 cm) not being twisted or not having fallen
into a speaker cabinet.
Note 6: When installing the loudspeaker (13 cm: right side) (woofer)
(SP2), after each screw holes of the loudspeaker (13 cm)
(woofer: right side) (SP2) and packing (13 cm) are aligned,
attach it to the speaker cabinet.
Note 7: When installing the loudspeaker (13 cm) (woofer: right side)
(SP2), install to a speaker cabinet after checking that a
loudspeaker terminal is on the diagonal left.
Note 1: When exchanging the loudspeaker (13 cm) (woofer: right side) (SP2),
refer to “NOTE THE SPEAKER UNITS REPLACING” on page 2.
SS-NA8ES
10
2-8. WO BOARD BLOCK
2 Remove four catchers from four shafts
of speaker cabinet.
4 After rotating WO board 90° within a speaker
cabinet, it pulls out from a speaker cabinet.
5 WO board block
MOUNT
(WO) board
(WO) board
TW board
left side
right side
center
shaft
shaft
brown
brown
blue
blue
brown brown
blue
blue
shaft
shaft
1 tapping screw
(BV3.5)
tightening torque:
1P
3 four terminals
Note
1: :KHQLQVWDOOLQJWHUPLQDOVFKHFN
WKDWWKHFDXONLQJSRUWLRQRID
WHUPLQDOLVERWWRPVLGHVXLWDEOH
– Speaker cabinet left inner side sectional view –
speaker cabinet
Wire (red) from WO board (left side)
Push into a slit of acoustic absorbent.
Note 3:6HHIURPWKHIURQWDQGOHWZLUHUHGSDVVRQOHIWVLGH
Push into a slit of acoustic absorbent.
Note 3:6HHIURPWKHIURQWDQGOHWZLUHUHGSDVVRQOHIWVLGH
Wire (black) from WO board (left side)
Push into a slit of acoustic
absorbent.
Note 3:6HHIURPWKHIURQWDQGOHW
Push into a slit of acoustic
absorbent.
Note 3:6HHIURPWKHIURQWDQGOHW
ZLUHUHGSDVVRQULJKWVLGH
Connect four terminals of wires from
TW board (right side).
Note 2:FKHFNWKDWDZLUHZDUQVDJDLQVW
TW board (right side).
Note 2:FKHFNWKDWDZLUHZDUQVDJDLQVW
SXOOLQJWRRPXFKDQGLVJHQHURXV
From the left
“AT IN –” wire (brown)
“AT IN+” wire (blue)
“TW IN –” wire (brown)
“TW IN+” wire (blue)
“AT IN –” wire (brown)
“AT IN+” wire (blue)
“TW IN –” wire (brown)
“TW IN+” wire (blue)
Wire (black) and wire (red)
are taken out to a center
through a partition.
are taken out to a center
through a partition.
Two short wires
“W1 –” wire (green/black)
“W1 +” wire (green)
Takes out from a front hole.
“W1 –” wire (green/black)
“W1 +” wire (green)
Takes out from a front hole.
Two long wires from WO board (left side)
“W2 –” wire (green/black)
“W2 +” wire (green)
After pushing in on a duct, it takes out to
right side through a partition.
Note 2:FKHFNWKDWDZLUHZDUQVDJDLQVW
“W2 –” wire (green/black)
“W2 +” wire (green)
After pushing in on a duct, it takes out to
right side through a partition.
Note 2:FKHFNWKDWDZLUHZDUQVDJDLQVW
SXOOLQJWRRPXFKDQGLVJHQHURXV
Two long wires from WO board (left side)
“W2 –” wire (green/black)
“W2 +” wire (green)
After letting a partition pass, it takes out to
right side through a central duct top.
Note 2:FKHFNWKDWDZLUHZDUQVDJDLQVW
“W2 –” wire (green/black)
“W2 +” wire (green)
After letting a partition pass, it takes out to
right side through a central duct top.
Note 2:FKHFNWKDWDZLUHZDUQVDJDLQVW
SXOOLQJWRRPXFKDQGLVJHQHURXV
“AT IN –” wire (brown)
“AT IN+” wire (blue)
“TW IN –” wire (brown)
“TW IN+” wire (blue)
After letting a partition pass,
it takes out to left side
through a center.
“AT IN+” wire (blue)
“TW IN –” wire (brown)
“TW IN+” wire (blue)
After letting a partition pass,
it takes out to left side
through a center.
“AT IN –” wire (brown)
“AT IN+” wire (blue)
“TW IN –” wire (brown)
“TW IN+” wire (blue)
Takes out to center
through a partition.
“AT IN+” wire (blue)
“TW IN –” wire (brown)
“TW IN+” wire (blue)
Takes out to center
through a partition.
Two long wires from WO board (left side)
“W2 –” wire (green/black)
“W2 +” wire (green)
Takes out from a front hole.
Note 2:FKHFNWKDWDZLUHZDUQVDJDLQVW
“W2 –” wire (green/black)
“W2 +” wire (green)
Takes out from a front hole.
Note 2:FKHFNWKDWDZLUHZDUQVDJDLQVW
SXOOLQJWRRPXFKDQGLVJHQHURXV
:ire settinJ
– Speaker cabinet inner side view –
SS-NA8ES
11
2-9. TW BOARD BLOCK
2-10. RETORQUING OF SCREWS
Retorquing all the screws of loudspeaker (13 cm) (woofer) (SP1, SP2) part, tweeter assy part and terminal board assy (TB1) part.
Tightening torque
•
•
Loudspeaker (13 cm) (woofer) (SP1, SP2) part (8 places): 2.0 ± 0.1 N•m
•
Tweeter assy part (6 places): 1.5 ± 0.1 N•m
•
Terminal board assy (TB1) part (4 places): 1.5 ± 0.1 N•m
Note 1:
The screw must not fl oat or the screw head must not be damaged.
Note 2:
If you will fl oat even retorque the screws, set up again not to exceed the numerical value of the following torque.
•
Loudspeaker (13 cm) (woofer) (SP1, SP2) part (4 places): 3.5 ± 0.1 N•m
•
Tweeter assy part (6 places): 2.0 ± 0.1 N•m
•
Terminal board assy (TB1) part (4 places): 2.0 N•m
2 Remove four catchers from four shafts
of speaker cabinet.
3 After rotating TW board 90° within a speaker
cabinet, it pulls out from a speaker cabinet.
4 TW board block
shaft
shaft
shaft
shaft
1 tapping screw
(BV3.5)
WLJKWHQLQJWRUTXH1P
– Speaker cabinet right inner side sectional view –
speaker cabinet
– Front side view –
– Rear side view –
tweeter assy part
six screws (3.5
six screws (3.5
u 20)
terminal board assy part
four screws (3.5
four screws (3.5
u 20)
loudspeaker (13 cm)
(woofer: left side) (SP1) part
four screws (4
(woofer: left side) (SP1) part
four screws (4
u 25)
loudspeaker (13 cm)
(woofer: right side) (SP2) part
four screws (4
(woofer: right side) (SP2) part
four screws (4
u 25)
12
SS-NA8ES
SECTION 3
EXPLODED VIEW
1
X-2581-995-1 GRILLE
FRAME
ASSY
2
4-235-903-02 SCREW
(3.5X20)
4
4-264-639-01 PACKING
(C)
5
4-235-904-02 SCREW
(4X25)
6
4-290-382-11 PACKING (13 cm)
7
4-874-614-82 +BV TAPPING SCREW TYPE-1 3.5
8
4-297-526-01 PACKING
(A)
9
3-095-290-01 FOOT
10
4-272-161-01 PACKING,
TERMINAL
12
4-912-253-01 CATCHER
13
4-286-322-01 SCREW, +BV B3.5X10 ROUNDED END
(for SERVICE)
14
4-449-207-01 BP CAP (BLACK)
15
4-449-207-11 BP CAP (RED)
MBT1
1-895-007-11 TW BOARD, COMPLETE
MBW1
1-895-008-11 WO BOARD, COMPLETE
SP1
1-858-654-11 LOUDSPEAKER (13 cm) (Woofer: left side)
SP2
1-858-654-11 LOUDSPEAKER (13 cm) (Woofer: right side)
SP3
1-858-571-12 LOUDSPEAKER (1.9 cm)
(Assist tweeter: upper side)
SP4
1-858-571-12 LOUDSPEAKER (1.9 cm)
(Assist tweeter: lower side)
SP5
A-1934-279-A SPEAKER (2.5 cm) ASSY (for SERVICE)
(Main tweeter) (Including FACE PLATE)
TB1
A-1800-115-A TERMINAL
BOARD
ASSY
Ref. No.
Part No.
Description
Remark
Ref. No.
Part No.
Description
Remark
Note:
• -XX and -X mean standardized parts, so
• -XX and -X mean standardized parts, so
they may have some difference from the
original one.
original one.
• Items marked “*” are not stocked since
they are seldom required for routine ser-
vice. Some delay should be anticipated
when ordering these items.
vice. Some delay should be anticipated
when ordering these items.
• The mechanical parts with no reference
number in the exploded views are not sup-
plied.
plied.
• Color Indication of Appearance Parts Ex-
ample:
KNOB, BALANCE (WHITE) . . . (RED)
Parts Color Cabinet’s Color
Note: When exchanging loudspeakers (SP1,
SP2, SP3, SP4, SP5), refer to “NOTE
THE SPEAKER UNITS REPLAC-
ING” on page 2.
THE SPEAKER UNITS REPLAC-
ING” on page 2.
ES
K
L
D
C
E F
F
E
C
D
B
B
A
H
G
I
I
J
J
A
H
G
K
L
2
not supplied
4
4
SP4
SP5
SP3
5
13
13
6
7
6
8 9
9
SP1
1
5
2
SP2
MBW1
MBT1
7
12
12
12
12
12
13
13
10
2
2
2
15
14
TB1
TERMINAL board
not supplied
Click on the first or last page to see other SS-NA8ES service manuals if exist.