Sony SS-NA5ES Service Manual ▷ View online
SS-NA5ES
5
2-3. TWEETER
ASSY
1
2
3
5
4
6
speaker cabinet
1 three screws
(3.5
u 20)
2 Pull out the tweeter assy.
Speaker cabinet
concave portion
concave portion
TW board
“AT–” wire (gray)
“AT–” wire (gray)
TW board
“AT+” wire (orange)
“AT+” wire (orange)
TW board
“TW–” wire (yellow/black)
“TW–” wire (yellow/black)
TW board
“TW+” wire (yellow)
“TW+” wire (yellow)
loudspeaker (1.9 cm) (assist tweeter)
(SP2) “–” wire (black)
(SP2) “–” wire (black)
loudspeaker (1.9 cm) (assist tweeter)
(SP1) “+” wire (gray)
(SP1) “+” wire (gray)
speaker (2.5 cm) assy
(SP3) “–” terminal
(SP3) “–” terminal
speaker (2.5 cm) assy
(SP3) “+” terminal
(SP3) “+” terminal
3 terminal (gray)
3 terminal
(yellow)
4 packing (A)
packing (A)
screw hole (six places)
-0.5 mm from a speaker cabinet upper surface.
3 terminal
(yellow/black)
3 terminal
(orange)
1 three screws
(3.5
u 20)
Note 1: When installing screws (3.5 × 20),
follow the installing procedure in
the numerical order given.
tightening torque :
1P
Note 2: When installing the tweeter assy, after each screw
holes of the tweeter assy and packing (A) are aligned,
attach it to the speaker cabinet.
Note 3: Check not having overflowed a speaker cabinet
upper surface.
Note 4: Check that there is neither a riding raising to the
speaker cabinet concave portion nor a position
gap of screw holes.
Note 5: Check that packing (A) is not turned over.
Note 10: Be careful not to attach a crack to a speaker
cabinet using the terminal of a wire.
Note 11: Check that the connection mistake or insertion
of a wire are not imperfect.
Note 12: Insert the terminal straightly.
Note 13: After terminal insertion, should check acting
Note 13: After terminal insertion, should check acting
as lock of the terminal completely.
Note 14: Check that the caulking
portion of a terminal is
outside
suitable.
Note 14: Check that the caulking
portion of a terminal is
outside
suitable.
caulking portion
caulking portion
5 tweeter assy
Note
6: When installing the tweeter assy,
be careful not to put wires.
Note
7: Be careful not to attach a crack to
the edge of a speaker cabinet.
Note
8: Do not touch the convex part of a
tweeter assy.
Note
9: Check that packing (A) has not
overflowed from a upper surface.
&DXWLRQVZKHQLQVWDOOLQJWKHSDFNLQJ$
:LUHVHWWLQJ
–8SSHUVLGHYLHZ–
SS-NA5ES
6
2-4. LOUDSPEAKER (1.9 cm) (ASSIST TWEETER) (SP1, SP2)
3 Lift up the loudspeaker
(1.9 cm) (assist tweeter:
upper side) (SP1).
5 loudspeaker (1.9 cm)
(assist
tweeter:
upper side) (SP1)
loudspeaker (1.9 cm) (assist tweeter: upper side)
(SP1)
(SP1)
loudspeaker (1.9 cm)
(assist tweeter:
upper side) (SP1)
“–” wire (black)
(assist tweeter:
upper side) (SP1)
“–” wire (black)
5 loudspeaker (1.9 cm)
(assist
tweeter:
lower side) (SP2)
loudspeaker (1.9 cm) (assist tweeter: lower side)
(SP2)
(SP2)
loudspeaker (1.9 cm)
(assist tweeter:
lower side) (SP2)
“+” wire (gray)
(assist tweeter:
lower side) (SP2)
“+” wire (gray)
tweeter assy
3 Lift up the loudspeaker
(1.9 cm) (assist tweeter:
lower side) (SP2).
speaker (2.5 cm) assy
(SP3)
(SP3)
speaker (2.5 cm) assy
(SP3)
(SP3)
4 packing (C)
packing (C) boss
packing (C) boss
4 packing (C)
convex
part
part
Note 2: When disassembling loudspeakers
(1.9 cm) (assist tweeter) (SP1, SP2),
place a stand etc. under tweeter assy
and be careful not to crush the convex
part of a speaker (2.5 cm) assy (SP3).
Note 9: When disassembling loudspeakers (1.9 cm) (assist tweeter)
(SP1, SP2), be sure to perform the polar check of "+" and
"í", to make "+" into the upper left side and to attach it, as
shown in the following figure.
Note 8: Check packing (C) not having
overlapped or not having run
aground.
Note 7: Do not touch the
convex
convex
part.
stand
stand
Note 10: Check that the connection mistake or insertion of a wire are not imperfect.
Note 11: Insert the terminal straightly.
Note 12: The arrangement of a wire should check that left side is gray and that right side is black.
Note 13: Check that a wire is on a speaker (2.5 cm) assy (SP3).
Note 11: Insert the terminal straightly.
Note 12: The arrangement of a wire should check that left side is gray and that right side is black.
Note 13: Check that a wire is on a speaker (2.5 cm) assy (SP3).
2 two screws (BV B3.5 u 10)
Note
3: When tightening screws, be
careful not to put the wire of
loudspeakers.
Note
4: Check that the screw has not
floated or it is not slanting.
Note
5: Check that packing (C) has
not overflowed the edge of
loudspeakers.
Note
6: tightening torque: .5 .5 1m
2 two screws (BV B3.5 u 10)
Note
3: When tightening screws, be
careful not to put the wire of
loudspeakers.
Note
4: Check that the screw has not
floated or it is not slanting.
Note
5: Check that packing (C) has
not overflowed the edge of
loudspeakers.
Note
6: tightening torque: .5 .5 1m
,QVWDOOHGSRVLWLRQRIORXGVSHDNHUFPDVVLVWWZHHWHU6363
,QVWDOOHGSRVLWLRQRISDFNLQJ&
1 terminal
(gray)
1 terminal
(black)
–,QQHUVLGHYLHZ–
–,QQHUERWWRPVLGHYLHZ–
–,QQHUVLGHYLHZ–
“+”
“–”
Note 1: When exchanging the loudspeaker (1.9 cm) (assist tweeter) (SP1, SP2),
refer to “NOTE THE SPEAKER UNITS REPLACING” on page 2.
SS-NA5ES
7
2-5. TERMINAL BOARD ASSY (TB1)
1
2
4
3
Note 1: When installing screws (3.5 × 20),
follow the installing procedure in
the numerical order given.
tightening torque :
.2 0.05 1m
Note 2: Please check direction of the upper and lower sides of terminal packing.
(Narrow side is the upper. Wide side is the bottom.)
Note 3: Check that terminal packing has not run aground with a terminal part.
Note 4: Push the whole terminal packing with a finger. Check the terminal packing
Note 4: Push the whole terminal packing with a finger. Check the terminal packing
not having shifted, not having floated or not being stuck.
Note 5: Check that terminal packing is not showing from screw holes of the terminal
board assy (TB1).
1 four screws
(3.5
u 20)
2 Pull out the terminal
board assy (TB1).
5 terminal board assy (TB1)
terminal board
assy “–” terminal
assy “–” terminal
terminal board
assy “+” terminal
assy “+” terminal
3 terminal (black)
terminal (black)
terminal (black)
3 terminal (red)
terminal (red)
terminal (red)
terminal
(black)
(black)
WO bord wire
(black)
(black)
WO bord wire
(red)
(red)
terminal
(red)
(red)
4 terminal
packing
terminal packing
caulking
part
part
caulking
part
part
Narrow side
upper side
Wide side
– Rear side view –
– Top side view –
Note 6: Check direction of terminals.
(terminal (black) is left side.
terminal (red) is right side.)
Note 7: Check that the caulking part of a terminal
has faced upward.
Note 8: Be careful not to attach a crack to a speaker
cabinet using the terminal of a wire.
Note 9: Check whether the terminal is inserted
conversely.
Note 10: Insert the terminal straightly.
Note 11: After terminal insertion, should check
conversely.
Note 10: Insert the terminal straightly.
Note 11: After terminal insertion, should check
acting as lock of the terminal completely.
:ire seWWiQJ
,QsWaOOed posiWioQ oI WerPiQaO paFNiQJ
SS-NA5ES
8
2-6. LOUDSPEAKER (13 cm) (WOOFER) (SP4)
1
3
2
4
1 four screws
(4
u 25)
2 Pull out the loudspeaker (13 cm) (woofer) (SP4).
3 terminal (green/black)
loudspeaker terminal
position
position
3 terminal (green)
4 packing (13 cm)
Note
5: When installing the packing (13 cm), a glossy
surface is made into the speaker cabinet side,
and a rough side is made into the loudspeaker
side, and align the position of the tapped hole
of packing (13 cm) and speaker cabinet.
5 loudspeaker (13 cm) (woofer) (SP4)
Note
8: Be careful not to attach a crack to a speaker cabinet using
the terminal of a wire.
Note
9: Be careful not to put a wire.
Note
10: Check that the connection mistake or insertion of a wire are
not
imperfect.
Note
11: Insert the terminal straightly.
Note
12: After terminal insertion, should check acting as lock of the
terminal
completely.
Note
13: Be careful not to attach a crack to the edge of a speaker cabinet.
Note
14: Check packing (13 cm) not being twisted or not having fallen
into a speaker cabinet.
Note 4: When installing screws (4 × 25),
follow the installing procedure in
the numerical order given.
tightening torque :
1P
Note 6: When installing the loudspeaker (13 cm) (woofer)
(SP4), after each screw holes of the loudspeaker
(13 cm) (woofer) (SP4) and packing (13 cm) are
aligned, attach it to the speaker cabinet.
Note 7: When installing the loudspeaker (13 cm) (woofer) (SP4),
install to a speaker cabinet after checking that a loudspeaker
terminal is on the diagonal left.
Note 2: Do not touch the central part of the
loudspeaker (13 cm) (woofer) (SP4).
Note 3: Check that the caulking portion of a terminal is outside suitable.
:LUHVHWWLQJ
loudspeaker (13 cm) (woofer)
(SP4) “–” terminal
(SP4) “–” terminal
loudspeaker (13 cm) (woofer)
(SP4) “+” terminal
(SP4) “+” terminal
caulking portion
WO board
“W2–” wire (green/black)
“W2–” wire (green/black)
WO board
“W2+” wire (green/)
“W2+” wire (green/)
Note 1: When exchanging the loudspeaker (13 cm) (woofer) (SP4), refer
to “NOTE THE SPEAKER UNITS REPLACING” on page 2.
Click on the first or last page to see other SS-NA5ES service manuals if exist.