Sony SRS-RF80R / SRS-RF80RK / TMR-RF80 Service Manual ▷ View online
4
SRS-RF80R/RF80RK/TMR-RF80
SECTION 1
GENERAL
This section is extracted from
instruction manual.
instruction manual.
1
First turn on the audio/video equipment
and start playing.
The power indicator of the transmitter
will light up.
and start playing.
The power indicator of the transmitter
will light up.
2
Turn on the speaker system.
The power indicator of the speaker
system will light in red.
The power indicator of the speaker
system will light in red.
3
Select the radio frequency with the
CHANNEL selector.
CHANNEL selector.
4
Turn up the volume to a moderate level
with the VOL control.
Press the TUNING button briefly for
automatic tuning of the speaker system.
If you do not receive a clear audio signal,
press it again.
with the VOL control.
Press the TUNING button briefly for
automatic tuning of the speaker system.
If you do not receive a clear audio signal,
press it again.
1
Connect the speaker system to a power
source.
2
The CHARGE indicator on the speaker
system will light up to indicate that the
battery is being charged.
battery is being charged.
1 2 3
CHANNEL
To an AC
outlet
outlet
AC power adaptor (supplied
UK model: AC-S911/
European model: AC-S906)
UK model: AC-S911/
European model: AC-S906)
Tweeter (left)
Tweeter (right)
CHARGE indicator
OFF y ON
The switch of the
reflector light
reflector light
POWER switch
POWER indicator
VOLUME control
High
Low
TUNING
button
button
A
To connect to a LINE OUT or REC OUT
B
To connect to LINE OUT or headphones
jacks
jacks
DC IN 9V
OFF
ON
FILTER
NOISE
1 2 3
CHANNEL
R
B
A
L
AUDIO IN
DC IN 9V
OFF
ON
FILTER
NOISE
1 2 3
CHANNEL
R
B
A
L
AUDIO IN
Transmitter
to AUDIO IN
B jack
B jack
Connecting cord
(supplied)
(supplied)
Right channel
(red)
(red)
Left channel
(white)
to LINE OUT or REC
OUT jacks
OUT jacks
Stereo system, VCR, etc.
Transmitter
Left channel
(white)
(white)
Right channel
(red)
(red)
Connecting cord
(supplied)
(supplied)
to AUDIO IN
A jacks
A jacks
Unimatch plug
adaptor (not
supplied)
adaptor (not
supplied)
MD, WALKMAN*,
VCR, etc.
VCR, etc.
to headphones or
LINE OUT jack
(stereomini jack)
LINE OUT jack
(stereomini jack)
to headphones
jack (stereo
phone jack)
jack (stereo
phone jack)
SRS-RF80R
TMR-RF80
5
SRS-RF80R/RF80RK/TMR-RF80
SECTION 2
DISASSEMBLY
Note :
Disassemble the unit in the order as shown below.
2-1. Grille Bracket
Note :
This set can be disassembled in the order shown below.
FRONT CABINET SECTION,
REAR CABINET SECTION
(Page 6)
GRILLE BRACKET
(Page 5)
SET (SRS-RF80R)
NICKEL CADMIUM BATTERY,
SPEAKER
(Page 6)
CABINET(TOP SECTION),
JACK BOARD, RX BOARD
JACK BOARD, RX BOARD
(Page 7)
AMP BOARD,
MEGABASS BOARD,
REFRECTOR BOARD
(Page 8)
CHARGE BOARD,
SW BOARD,
(Page 7)
DRIVE(030F034)
(Page 8)
2
jack holder
4
grille bracket
(Cautions)
(Cautions)
Please also exchange grille (Dia. 57) together at a Grille bracket.
(A grille (Dia. 57) is unreproducible.)
Please also exchange grille (Dia. 57) together at a Grille bracket.
(A grille (Dia. 57) is unreproducible.)
3
grille (Dia. 57)
(Cautions)
1
three
screws
(+P 3
×
10)
The cautions at the time of attachment :
When you attach a grille (Dia. 57), please unite
a position by cut of a grille (Dia. 57).
When you attach a grille (Dia. 57), please unite
a position by cut of a grille (Dia. 57).
6
SRS-RF80R/RF80RK/TMR-RF80
2-2. Front Cabinet Section, Rear Cabinet Section
2-3. Nickel Cadmium Battery, Speaker (057F022)
6
eight
screws
(+BVTP 3
×
12)
2
three
screws
(+P 3
×
10)
4
two
screws
(+P 3
×
10)
1
reflector
8
connector
(CN203)
7
connector
(CN802)
3
jack holder
5
stand
rear cabinet section
9
front cabinet section
2
two claws
4
nickel. cadmium battery
3
retainer board
1
screws
(+BVTP 3
×
10)
5
two screws
(+BVTP 3
×
10)
6
speaker (057F022)
front cabinet
7
SRS-RF80R/RF80RK/TMR-RF80
2-4. Cabinet (Top Section), JACK board, RX board
2-5. CHARGE board, SW board
1
connector (CN302)
7
connector (CN801)
8
connector
(CN804)
qa
connector
(CN101)
qs
antenna
qd
RX board
4
connector (CN304)
6
cabinet
(top section)
2
connector
(CN301)
3
power button
q;
JACK board
5
two
screws
(+BVTP 3
×
10)
9
screw (DIA. 12)
rear cabinet
3
CHARGE board
5
SW board
2
connector (CN303)
1
screw
(+P 2.6
×
4)
4
two screws
(+P 2.6
×
6)
top cover section