Sony SRS-D4100 / SRS-D5100 Service Manual ▷ View online
SRS-D4100/D5100
US Model
AEP Model
SRS-D4100/D5100
Canadian Model
UK Model
Korean Model
SRS-D5100
SERVICE MANUAL
ACTIVE SPEAKER SYSTEM
Sony Corporation
Parsonal Audio Company
Published by Sony Engineering Corporation
Published by Sony Engineering Corporation
9-877-701-02
2004E02-1
© 2004.05
SPECIFICATIONS
Ver 1.1 2004. 05
Subwoofer
Satellite
Speaker
Speaker
Control Box
Photo : SRS-D5100
Speaker section
Satellite speaker
Satellite speaker
Speaker system
Full range, magnetically shielded
Speaker units
5.6 cm, cone type
Enclosure type
Closed type
Impedance
6
Ω
Cord length
3 m
Subwoofer
Speaker system
Woofer
Speaker units
16 cm, cone type
Enclosure type
Bass reflex
Impedance
6
Ω
Amplifier section
Rated output
Rated output
12 W (10% T.H.D., 1 kHz, 6
Ω)
(Satellite speaker)
80 W (10% T.H.D., 100 Hz, 6
80 W (10% T.H.D., 100 Hz, 6
Ω)
(Subwoofer)
Input
Stereo mini jack x 3
(INPUT 1 for 5.1 channel signal input)
(D5100)
Stereo mini jack x 2
(INPUT 1 for 4 channel signal input)
(D4100)
Stereo mini jack x 1
(INPUT 2 for 2 channel signal input)
(INPUT 1 for 5.1 channel signal input)
(D5100)
Stereo mini jack x 2
(INPUT 1 for 4 channel signal input)
(D4100)
Stereo mini jack x 1
(INPUT 2 for 2 channel signal input)
Input impedance
4.7 k
Ω (at 1 kHz)
Output
Stereo mini jack x1 (PHONES)
General
Dimensions (w/h/d)
Dimensions (w/h/d)
Approx. 166 x 40 x 83 mm
(6
(6
5
/
8
x 1
5
/
8
x 3
3
/
8
in.) (Control box)
Approx. 95 x 135 x 150 mm
(3
(3
3
/
4
x 5
3
/
8
x 6 in.)
(Satellite speaker, on a desk)
Approx. 95 x 100 x180 mm
(3
Approx. 95 x 100 x180 mm
(3
3
/
4
x 4 x 7
1
/
8
in.)
(Satellite speaker, attached to a wall)
Approx. 285 x 285 x 462 mm
(11
Approx. 285 x 285 x 462 mm
(11
1
/
4
x 11
1
/
4
x 18
1
/
4
in.)(Subwoofer)
Mass
Approx. 240 g (8 oz.) (Control box)
Approx. 490 g (1 lb. 1 oz.)
(Satellite speaker)
Approx. 8.7 kg (19 lb. 3 oz.)(Subwoofer)
(D5100)
Approx. 8.6 kg (18 lb. 15 oz.)(Subwoofer)
(D4100)
Approx. 490 g (1 lb. 1 oz.)
(Satellite speaker)
Approx. 8.7 kg (19 lb. 3 oz.)(Subwoofer)
(D5100)
Approx. 8.6 kg (18 lb. 15 oz.)(Subwoofer)
(D4100)
Cord length
2 m (Control box to subwoofer)
2 m (Power cord)
2 m (Power cord)
Power consumptions
42 W (D5100)
41 W (D4100)
41 W (D4100)
Power requirements
Where purchased
Operating voltage
US, Canadian model
120 V AC, 60 Hz
AEP, UK, Korean model
220 – 230 V AC, 50 Hz
Supplied accessories
Connecting Cable (for 5.1 channel signal input) (D5100)
Connecting Cable (for 4 channel signal input) (D4100)
Connecting Cable (for 5.1 channel signal input) (D5100)
Connecting Cable (for 4 channel signal input) (D4100)
Design and specifications are subject to change without notice.
2
SRS-D4100/D5100
TABLE OF CONTENTS
Specifications ............................................................................ 1
1.
GENERAL
................................................................... 3
2.
DIAGRAMS
2-1.
Schematic Diagram – Amp Section– ............................... 5
2-2.
Printed Wiring Boards– Amp Section (Side A)– ............. 6
2-3.
Printed Wiring Boards– Amp Section (Side B)– ............. 7
2-4.
Printed Wiring Boards – Control Section (D5100)– ....... 8
2-5.
Printed Wiring Boards – Control Section (D4100)– ....... 9
2-6.
Schematic Diagram – Control Section– .......................... 10
3.
EXPLODED VIEWS
3-1.
Subwoofer Section .......................................................... 11
3-2.
Control Box, Satellite Speaker Section ........................... 12
4.
ELECTRICAL PARTS LIST
.................................. 13
SAFETY CHECK-OUT
After correcting the original service problem, perform the following
safety checks before releasing the set to the customer:
Check the antenna terminals, metal trim, “metallized” knobs, screws,
and all other exposed metal parts for AC leakage. Check leakage as
described below.
safety checks before releasing the set to the customer:
Check the antenna terminals, metal trim, “metallized” knobs, screws,
and all other exposed metal parts for AC leakage. Check leakage as
described below.
LEAKAGE
The AC leakage from any exposed metal part to earth Ground and
from all exposed metal parts to any exposed metal part having a
return to chassis, must not exceed 0.5 mA (500 microampers).
Leakage current can be measured by any one of three methods.
from all exposed metal parts to any exposed metal part having a
return to chassis, must not exceed 0.5 mA (500 microampers).
Leakage current can be measured by any one of three methods.
1. A commercial leakage tester, such as the Simpson 229 or RCA
WT-540A. Follow the manufacturers’ instructions to use these
instruments.
instruments.
2. A battery-operated AC milliammeter. The Data Precision 245
digital multimeter is suitable for this job.
3. Measuring the voltage drop across a resistor by means of a
VOM or battery-operated AC voltmeter. The “limit” indication
is 0.75 V, so analog meters must have an accurate low-voltage
scale. The Simpson 250 and Sanwa SH-63Trd are examples
of a passive VOM that is suitable. Nearly all battery operated
digital multimeters that have a 2V AC range are suitable. (See
Fig. A)
is 0.75 V, so analog meters must have an accurate low-voltage
scale. The Simpson 250 and Sanwa SH-63Trd are examples
of a passive VOM that is suitable. Nearly all battery operated
digital multimeters that have a 2V AC range are suitable. (See
Fig. A)
Fig. A. Using an AC voltmeter to check AC leakage.
0.15
µ
F
To Exposed Metal
Parts on Set
Parts on Set
1.5k
Ω
AC
voltmeter
(0.75V)
voltmeter
(0.75V)
Earth Ground
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK
0
OR DOTTED LINE
WITH MARK
0
ON THE SCHEMATIC DIAGRAMS AND IN THE
PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE
THESE COMPONENTS WITH SONY PARTS WHOSE PART
NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN
SUPPLEMENTS PUBLISHED BY SONY.
THESE COMPONENTS WITH SONY PARTS WHOSE PART
NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN
SUPPLEMENTS PUBLISHED BY SONY.
ATTENTION AU COMPOSANT AYANT RAPPORT
À LA SÉCURITÉ!!
LES COMPOSANTS IDENTIFIÉS PAR UNE MARQUE
0
SUR LES
DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES
SONT CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT.
NE REMPLACER CES COMPOSANTS QUE PAR DES PIÈCES
SONY DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL
OU DANS LES SUPPLÉMENTS PUBLIÉS PAR SONY.
SONT CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT.
NE REMPLACER CES COMPOSANTS QUE PAR DES PIÈCES
SONY DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL
OU DANS LES SUPPLÉMENTS PUBLIÉS PAR SONY.
3
SRS-D4100/D5100
SECTION 1
GENERAL
This section is extracted
from instruction manual.
from instruction manual.
LOCATING THE CONTROLS
VOLUME
BASS
REAR
CENTER
PHONE
ON
OFF
POWER
ON
OFF
Dual Stereo
MIN
MAX
POWER
VOLUME
PHONES
DUAL STEREO
Control box
VOLUME
BASS
REAR
PHONE
ON
OFF
POWER
ON
OFF
DUAL STEREO
MIN
MAX
POWER
VOLUME
PHONES
DUAL STEREO
Control box
D5100
D4100
4
SRS-D4100/D5100
SECTION 2
DIAGRAMS
For schematic diagrams.
Note:
Note:
• All capacitors are in
µ
F unless otherwise noted. pF:
µµ
F 50 WV or
less are not indicated except for electrolytics and tantalums.
• All resistors are in
Ω
and
1
/
4
W or less unless otherwise specified.
•
C
: panel designation.
•
A
: B+ Line.
•
B
: B– Line.
• Voltages are dc with respect to ground under no-signal conditions.
• no mark : Power on
• Voltages are taken with a VOM (Input impedance 10 M
• no mark : Power on
• Voltages are taken with a VOM (Input impedance 10 M
Ω
).
Voltage variations may be noted due to normal production toler-
ances.
ances.
• Signal path.
F
: AUDIO
• Abbreviation
CND : Canadian model
KR
KR
: Korean model
THIS NOTE IS COMMON FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS.
(In addition to this necessary note is printed in each block.)
(In addition to this necessary note is printed in each block.)
Note:
The components identi-
fied by mark
fied by mark
0
or dotted
line with mark
0
are criti-
cal for safety.
Replace only with part
number specified.
Replace only with part
number specified.
Note:
Les composants identifiés par
une marque
une marque
0
sont critiques
pour la sécurité.
Ne les remplacer que par une
piéce portant le numéro
spécifié.
Ne les remplacer que par une
piéce portant le numéro
spécifié.
For printed wiring boards.
Note:
• X
Note:
• X
: parts extracted from the component side.
•
: Pattern from the side which enables seeing.
• Abbreviation
CND : Canadian model
KR
KR
: Korean model
Ver 1.1