Sony SRS-D313 Service Manual ▷ View online
Sony Corporation
Personal Audio Company
Published by Sony Engineering Corporation
9-873-230-05
2002K1600-1
© 2002.11
SRS-D313
US Model
Canadian Model
AEP Model
UK Model
E Model
Australian Model
Tourist Model
SERVICE MANUAL
ACTIVE SPEAKER SYSTEM
SPECIFICATIONS
Ver 1.4 2002. 11
Front speakers
Speaker system
Full range, magnetically shielded
Speaker units
3.9 cm, cone type
Enclosure type
Bass reflex
Rated impedance
8
Ω
Power handling capacity
5 watts
Maximum input power
10 watts
Sensitivity level
80 dB (1 W, 1 m)
Dimensions (w/h/d)
72
× 179 × 108 mm
Mass
265 g (Lch), 220 g (Rch)
Cord length
2 m
Input impedance
4.7 k
Ω (at 1 kHz)
Input
LINE IN 1, 2
Output
PHONES
Subwoofer
Speaker system
Active subwoofer, magnetically shielded
Speaker unit
10 cm, cone type
Enclosure type
Bass reflex
Rated impedance
8
Ω
Sensitivity level
83 db (1 W, 1 m)
Dimensions (w/h/d)
214
× 254 × 290 mm
Mass
3,300 g
Amplifier section
Rated output:
Rated output:
Woofer section
20 W
Mid and high range section 5 W + 5 W
Total
Total
30 W 10 % T.H.D., 8
General
Power consumptions
30 W
Cord length
2 m (adaptor cable)
Supplied accessories
Audio connecting cord (1)
Design and specifications are subject to change without notice.
2
SRS-D313
SAFETY CHECK-OUT
After correcting the original service problem, perform the following
safety check before releasing the set to the customer:
Check the antenna terminals, metal trim, “metallized” knobs, screws,
and all other exposed metal parts for AC leakage.
Check leakage as described below.
safety check before releasing the set to the customer:
Check the antenna terminals, metal trim, “metallized” knobs, screws,
and all other exposed metal parts for AC leakage.
Check leakage as described below.
LEAKAGE TEST
The AC leakage from any exposed metal part to earth ground and
from all exposed metal parts to any exposed metal part having a
return to chassis, must not exceed 0.5 mA (500 microamperes.).
Leakage current can be measured by any one of three methods.
from all exposed metal parts to any exposed metal part having a
return to chassis, must not exceed 0.5 mA (500 microamperes.).
Leakage current can be measured by any one of three methods.
1. A commercial leakage tester, such as the Simpson 229 or RCA
WT-540A. Follow the manufacturers’ instructions to use these
instruments.
instruments.
2. A battery-operated AC milliammeter. The Data Precision 245
digital multimeter is suitable for this job.
3. Measuring the voltage drop across a resistor by means of a VOM
or battery-operated AC voltmeter. The “limit” indication is 0.75
V, so analog meters must have an accurate low-voltage scale.
The Simpson 250 and Sanwa SH-63Trd are examples of a
passive VOM that is suitable. Nearly all battery operated digital
multimeters that have a 2 V AC range are suitable. (See Fig. A)
V, so analog meters must have an accurate low-voltage scale.
The Simpson 250 and Sanwa SH-63Trd are examples of a
passive VOM that is suitable. Nearly all battery operated digital
multimeters that have a 2 V AC range are suitable. (See Fig. A)
To Exposed Metal
Parts on Set
0.15
µF
1.5 k
Ω
AC
Voltmeter
(0.75 V)
Voltmeter
(0.75 V)
Earth Ground
Fig. A. Using an AC voltmeter to check AC leakage.
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK
0
OR DOTTED LINE WITH
MARK
0
ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS
LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE
COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS
APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS
PUBLISHED BY SONY.
COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS
APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS
PUBLISHED BY SONY.
ATTENTION AU COMPOSANT AYANT RAPPORT
À LA SÉCURITÉ!
LES COMPOSANTS IDENTIFÉS PAR UNE MARQUE
0
SUR LES
DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT
CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE
REMPLACER CES COMPOSANTS QUE PAR DES PIÈSES SONY
DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU
DANS LES SUPPÉMENTS PUBLIÉS PAR SONY.
CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE
REMPLACER CES COMPOSANTS QUE PAR DES PIÈSES SONY
DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU
DANS LES SUPPÉMENTS PUBLIÉS PAR SONY.
Notes on chip component replacement
• Never reuse a disconnected chip component.
• Notice that the minus side of a tantalum capacitor may be
• Notice that the minus side of a tantalum capacitor may be
damaged by heat.
Ver 1.2 2001.12
3
SRS-D313
SECTION 1
GENERAL
This section is extracted from
instruction manual.
instruction manual.
C
B
Front (Right)/Avant (droite)
Vorne (rechts)/Parte frontal (derecha)
Vorne (rechts)/Parte frontal (derecha)
Subwoofer
Caisson de grave
Tiefsttonlautsprecher
Potenciación de graves
Caisson de grave
Tiefsttonlautsprecher
Potenciación de graves
Front (Right)/Avant (droite)
Vorne (rechts)/Parte frontal (derecha)
Vorne (rechts)/Parte frontal (derecha)
Front (Left)/Avant (gauche)
Vorne (links)/Parte frontal (izquierda)
Vorne (links)/Parte frontal (izquierda)
A
POWER
(OPERATE for European model)
(OPERATE pour le modèle européen)
(OPERATE beim Modell für Europa)
(OPERATE para el modelo europeo)
(OPERATE for European model)
(OPERATE pour le modèle européen)
(OPERATE beim Modell für Europa)
(OPERATE para el modelo europeo)
BASS
VOLUME
INPUT
Note PC
PC Note
Notebook-PC
Portátil
PC Note
Notebook-PC
Portátil
Attach the reflectors (no distinction between right and left) to the speakers as shown
Fixez les réflecteurs (pas de distinction entre le réflecteur gauche et le droit) sur les enceintes comme indiqué ci-dessous.
Bringen Sie die Reflektoren (kein Unterschied zwischen rechts und links) wie abgebildet an den Lautsprechern an.
Conecte los reflectores (no hay distinción entre derecho e izquierdo) a los altavoces, tal como se muestra .
Fixez les réflecteurs (pas de distinction entre le réflecteur gauche et le droit) sur les enceintes comme indiqué ci-dessous.
Bringen Sie die Reflektoren (kein Unterschied zwischen rechts und links) wie abgebildet an den Lautsprechern an.
Conecte los reflectores (no hay distinción entre derecho e izquierdo) a los altavoces, tal como se muestra .
PHONES
Front (Left)/Avant (gauche)
Vorne (links)/Parte frontal (izquierda)
Vorne (links)/Parte frontal (izquierda)
PC/Ordinateur
PC/PC
PC/PC
CD Walkman
Walkman CD
CD-Walkman
CD Walkman
Walkman CD
CD-Walkman
CD Walkman
to 8 pin Din jack
vers la prise Din à 8 broches
an 8 polige DIN-Buchse
a conector DIN de 8 patillas
vers la prise Din à 8 broches
an 8 polige DIN-Buchse
a conector DIN de 8 patillas
to Mono Mini Jack
vers la mini prise mono
an Mono-Ministecker
a minienchufe mono
vers la mini prise mono
an Mono-Ministecker
a minienchufe mono
to wall outlet
vers la prise murale
an eine Netzsteckdose
a la toma de corriente
vers la prise murale
an eine Netzsteckdose
a la toma de corriente
POWER
ON
OFF
MIN
MAX
MIN
MAX
1
2
VOLUME
BASS
INPUT
PHONES
L
*
* This switch is only for
European models.
Cet interrupteur ne concerne
que les modèles européens.
Dieser Schalter ist nur für
Modelle für Europa.
Este interruptor sólo está
destinado a los modelos
europeos.
Cet interrupteur ne concerne
que les modèles européens.
Dieser Schalter ist nur für
Modelle für Europa.
Este interruptor sólo está
destinado a los modelos
europeos.
D
Subwoofer
Caisson de grave
Tiefsttonlautsprecher
Potenciación de graves
Caisson de grave
Tiefsttonlautsprecher
Potenciación de graves
Hooking up the system
1
Attach the reflector to the speakers.
(See fig. A.)
2
(See fig. B for steps 2 through 4.)
Connect the left speaker cord 8 pin plug to the rear
panel jack with their respective arrows aligned.
panel jack with their respective arrows aligned.
3
Connect the subwoofer to the wall outlet.
4
Connect the CD walkman, PC, etc., to the INPUT
jack on the left speaker.
jack on the left speaker.
5
Position the speakers.
(See fig. C.)
Listening to the sound
(see fig. D)
First, turn down the volume on the left speaker. The volume
should be set to minimum before you begin playing the
programme source.
should be set to minimum before you begin playing the
programme source.
1
Press POWER on the left speaker.
The POWER indicator lights up green.
For the European models
Press POWER on the subwoofer to turn it on, and then
press OPERATE on the left speaker.
The OPERATE indicator lights up green.
The main power source of the system is provided by the
subwoofer. When the power of the subwoofer is turned off,
the system does not operate, even if OPERATE is pressed.
For the European models
Press POWER on the subwoofer to turn it on, and then
press OPERATE on the left speaker.
The OPERATE indicator lights up green.
The main power source of the system is provided by the
subwoofer. When the power of the subwoofer is turned off,
the system does not operate, even if OPERATE is pressed.
2
Rotate INPUT to select 1/2.
You can enjoy the mixed sound from INPUT 1 and 2.
3
Play the programme source.
To adjust the volume
Rotate VOLUME.
To adjust the subwoofer
Rotate BASS to adjust the bass volume.
Set the volume level to best suit your preference according to the
programme source.
Set the volume level to best suit your preference according to the
programme source.
Using the headphones/earphones
Connect the headphones/earphones to the PHONES jack.
Notes
• To enjoy high-quality sound, do not turn the BASS
Notes
• To enjoy high-quality sound, do not turn the BASS
volume too high.
• When using the headphones, you cannot adjust the bass
volume.
Troubleshooting
Should you encounter a problem with your speaker system, check
the following list and take the indicated measures. If the problem
persists, consult your nearest Sony dealer.
the following list and take the indicated measures. If the problem
persists, consult your nearest Sony dealer.
There is no sound from the speaker system.
• Make sure all the connections have been correctly made.
• Make sure the volume on the left speaker and the connected
component have been turned up properly.
• Check if headphones are connected. If they are, disconnect them.
There is distortion in the subwoofer sound output.
• Turn down the volume level on the connected component. Or,
if the connected component has the bass boost function, set it to
off.
• Rotate BASS on this unit to reduce the bass volume.
There is hum or noise in the speaker output.
• Make sure all the connections have been correctly made.
• Make sure none of the audio components are positioned too
close to the TV set.
The sound has suddenly stopped.
Make sure all the connections have been correctly made.
4
SRS-D313
SECTION 2
DIAGRAMS
Note on Schematic Diagram:
• All capacitors are in
• All capacitors are in
µ
F unless otherwise noted. pF:
µµ
F
50 WV or less are not indicated except for electrolytics
and tantalums.
and tantalums.
• All resistors are in
Ω
and
1
/
4
W or less unless otherwise
specified.
•
C
: panel designation.
•
A
: B+ Line.
•
B
: B– Line.
•
H
: adjustment for repair.
• Power voltage is dc 9V and fed with regulated dc power
supply from battery terminal.
• Voltages is dc with respect to ground under no-signal
(detuned) conditions.
• Voltages are taken with a VOM (Input impedance 10 M
Ω
).
Voltage variations may be noted due to normal produc-
tion tolerances.
tion tolerances.
• Signal path.
E
: AUDIO signal
Note on Printed Wiring Boards:
•
•
X
: parts extracted from the component side.
•
b
: Pattern from the side which enables seeing.
Ver 1.2 2001.12
The components identified by
mark
mark
0
or dotted line with mark
0
are critical for safety.
Replace only with part number
specified.
specified.
Les composants identifiés par
une marque
une marque
0
sont critiques
pour la sécurité.
Ne les remplacer que par une
pièce portant le numéro spécifié.
Ne les remplacer que par une
pièce portant le numéro spécifié.