Sony SRF-H11 (serv.man2) Service Manual ▷ View online
FM STEREO / AM HEADPHONE RADIO
French Model
SRF-H11
Ver 1.0 2003.04
9-877-300-01
Sony Corporation
2003D0200-1
Personal Audio Company
C
2003.04
Published by Sony Engineering Corporation
SPECIFICATIONS
Frequency range
FM:87.5 – 108 MHz
AM:530 – 1 710 kHz
AM:530 – 1 710 kHz
Power output
6 mW + 6 mW (at 10% harmonic distortion)
Headphone type
Dynamic
Power requirements
1.5 V DC, one R03 (size AAA) battery
Mass Approx. 115 g (4 oz) incl. a battery
Design and specifications are subject to change without notice.
SERVICE MANUAL
SRF-H11
2
TABLE OF CONTENTS
Specifications ............................................................................ 1
1.
SERVICING NOTE
................................................... 3
2.
GENERAL
Location and Function of Controls ................................. 4
3.
DISASSEMBLY
3-1. Belt Removal ........................................................... 5
3-2. Driver (Headphone) (R) Removal ........................... 5
3-3. Driver (Headphone) (L) Removal ........................... 5
3-4. Main Board Removal .............................................. 6
3-5. Audio Board Removal ............................................. 6
3-2. Driver (Headphone) (R) Removal ........................... 5
3-3. Driver (Headphone) (L) Removal ........................... 5
3-4. Main Board Removal .............................................. 6
3-5. Audio Board Removal ............................................. 6
4.
GEAR (TUNING CAPACITOR)
INSTALLATION
INSTALLATION
........................................................ 7
5.
ELECTRICAL ADJUSTMENTS
.......................... 8
6.
DIAGRAMS
6-1. Printed Wiring Boards ............................................. 11
6-2. Schematic Diagram ................................................. 12
6-2. Schematic Diagram ................................................. 12
7.
EXPLODED VIEW
.................................................... 14
8.
ELECTRICAL PARTS LIST
.................................. 15
Notes on chip component replacement
• Never reuse a disconnected chip component.
• Notice that the minus side of a tantalum capacitor may be dam-
• Never reuse a disconnected chip component.
• Notice that the minus side of a tantalum capacitor may be dam-
aged by heat.
• UNLEADED SOLDER
Boards requiring use of unleaded solder are printed with the
lead-free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed
with the lead free mark due to their particular size.)
: LEAD FREE MARK
Unleaded solder has the following characteristics.
• Unleaded solder melts at a temperature about 40
• Unleaded solder melts at a temperature about 40
°C higher
than ordinary solder.
Ordinary soldering irons can be used but the iron tip has to
be applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set
to about 350
be applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set
to about 350
°C.
Caution: The printed pattern (copper foil) may peel away if
the heated tip is applied for too long, so be careful!
the heated tip is applied for too long, so be careful!
• Strong viscosity
Unleaded solder is more viscous (sticky, less prone to flow)
than ordinary solder so use caution not to let solder bridges
occur such as on IC pins, etc.
than ordinary solder so use caution not to let solder bridges
occur such as on IC pins, etc.
• Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder
may also be added to ordinary solder.
may also be added to ordinary solder.
3
SRF-H11
SECTION 1
SERVICING NOTE
TSE392-W
TSE392-W
Poly-slider washer
Lever
Knob (band)
Knob
(tune)
(tune)
Knob (power)
Knob
(volume)
(volume)
TSE392-W
TSE392-W
Cabinet (rear) R
Cabinet (rear) L
Cabinet (rear) R
Cabinet (rear) R
Cabinet (rear) L
Cabinet (rear) L
Lever
DRIP-PROOF TREATMENT
Be sure to execute the following, when the cabinet is removed
during service.
Apply the SONY coating sealant TSE392-W (7-432-950-03) to
the hatched portion shown in figure using an applicator, etc.
Be sure to execute the following, when the cabinet is removed
during service.
Apply the SONY coating sealant TSE392-W (7-432-950-03) to
the hatched portion shown in figure using an applicator, etc.
4
SRF-H11
SECTION 2
GENERAL
This section is extracted from
instruction manual.
instruction manual.
P
O
W
ER
OF
F
ON
VOL
FM
DX
AM
B
A
N
D
LO
CA
L
L
R
Driver units
Neck band/Bandeau/
Battery compartment
BAND
FM DX/LOCAL•AM
FM DX/LOCAL•AM
TUNE
R03 (size AAA) x 1
L
A
POWER OFF•ON•
MEGA BASS
MEGA BASS
VOL
*
Left ear/Oreille gauche/ Linkes
Neck band
C
Light reflector (R, L)
This reflector reflects car
lights at night for your safety.
lights at night for your safety.
B
L
f
f
Location and function of controls