Sony SCD-XE670 Service Manual ▷ View online
4
SCD-XE670
(1) CD
1.
Sled reverse move (sled in)
2.
Disc detect
3.
IC setting for CD
4.
Servo error signal offset auto adjustment
5.
Spindle kick for LD on
6.
LD on
7.
Focus search
8.
Focus servo on
9.
Spindle kick
10. Spindle servo on
11. E-F balance auto adjustment
12. Tracking & sled servo on
13. Focus bias auto adjustment
14. Focus servo gain auto adjustment
15. Tracking servo gain auto adjustment
16. Jump to lead-in area
17. Read TOC
18. Stop
11. E-F balance auto adjustment
12. Tracking & sled servo on
13. Focus bias auto adjustment
14. Focus servo gain auto adjustment
15. Tracking servo gain auto adjustment
16. Jump to lead-in area
17. Read TOC
18. Stop
(2) SACD (single layer)
1.
Sled reverse move (sled in)
2.
Disc detect
3.
IC setting for SACD
4.
Servo error signal offset auto adjustment
5.
Spindle kick for LD on
6.
LD on
7.
Focus search
8.
Focus servo on
9.
Spindle kick
10. Spindle servo on
11. E-F balance auto adjustment
12. Tracking & sled servo on
13. Focus bias auto adjustment
14. Focus servo gain auto adjustment
15. Tracking servo gain auto adjustment
16. Jump to lead-in area
17. Read TOC
18. Stop
11. E-F balance auto adjustment
12. Tracking & sled servo on
13. Focus bias auto adjustment
14. Focus servo gain auto adjustment
15. Tracking servo gain auto adjustment
16. Jump to lead-in area
17. Read TOC
18. Stop
(3) SACD (dual layer)
1.
Sled reverse move (sled in)
2.
Disc detect
3.
IC setting for SACD
4.
Servo error signal offset auto adjustment
5.
Spindle kick for LD on
6.
LD on
7.
Focus search
8.
Focus servo on (layer 0)
9.
Spindle kick
10. Spindle servo on
11. E-F balance auto adjustment (layer 0)
12. Tracking & sled servo on (layer 0)
13. Focus bias auto adjustment (layer 0)
14. Focus servo gain auto adjustment (layer 0)
15. Tracking servo gain auto adjustment (layer 0)
16. Jump to lead-in area
17. Read TOC
18. Focus jump (layer 0
11. E-F balance auto adjustment (layer 0)
12. Tracking & sled servo on (layer 0)
13. Focus bias auto adjustment (layer 0)
14. Focus servo gain auto adjustment (layer 0)
15. Tracking servo gain auto adjustment (layer 0)
16. Jump to lead-in area
17. Read TOC
18. Focus jump (layer 0
tlayer 1)
19. E-F balance auto adjustment (layer 1)
20. Tracking & sled servo on (layer 1)
21. Focus bias auto adjustment (layer 1)
22. Focus servo gain auto adjustment (layer 1)
23. Tracking servo gain auto adjustment (layer 1)
24. Focus Jump (layer 1
20. Tracking & sled servo on (layer 1)
21. Focus bias auto adjustment (layer 1)
22. Focus servo gain auto adjustment (layer 1)
23. Tracking servo gain auto adjustment (layer 1)
24. Focus Jump (layer 1
tlayer 0)
25. Stop
SECTION 1
SERVICING NOTES
The laser diode in the optical pick-up block may suffer electro-
static break-down because of the potential difference generated
by the charged electrostatic load, etc. on clothing and the human
body.
During repair, pay attention to electrostatic break-down and also
use the procedure in the printed matter which is included in the
repair parts.
The flexible board is easily damaged and should be handled with
care.
static break-down because of the potential difference generated
by the charged electrostatic load, etc. on clothing and the human
body.
During repair, pay attention to electrostatic break-down and also
use the procedure in the printed matter which is included in the
repair parts.
The flexible board is easily damaged and should be handled with
care.
NOTES ON LASER DIODE EMISSION CHECK
The laser beam on this model is concentrated so as to be focused
on the disc reflective surface by the objective lens in the optical
pick-up block. Therefore, when checking the laser diode emis-
sion, observe from more than 30 cm away from the objective lens.
on the disc reflective surface by the objective lens in the optical
pick-up block. Therefore, when checking the laser diode emis-
sion, observe from more than 30 cm away from the objective lens.
CLEANING OF OPTICAL PICK-UP LENS
In cleaning the lens of optical pick-up, use the air blower.
Never use a cotton swab for cleaning the lens of optical pick-up,
which otherwise causes a trouble.
Never use a cotton swab for cleaning the lens of optical pick-up,
which otherwise causes a trouble.
MODEL IDENTIFICATION
– Rear Panel –
RESETTING OPERATION AT POWER ON
If the power is turned on with a disc loaded in the set, a sequence
of operation as shown below will be performed.
(The operation varies depending on the type of disc)
Condition: continue mode
of operation as shown below will be performed.
(The operation varies depending on the type of disc)
Condition: continue mode
NOTES ON HANDLING THE OPTICAL PICK-UP
BLOCK OR BASE UNIT
BLOCK OR BASE UNIT
PART No.
MODEL
PART No.
AEP and UK models
4-234-033-0
[]
US model
4-234-033-2
[]
Canadian model
4-234-033-4
[]
5
SCD-XE670
HOW TO OPEN THE TRAY WHEN POWER SWITCH TURNS OFF
DISPLAY BOARD SERVICE POSITION
In checking the DISPLAY board, prepare jig (extension cable J-8000-024-A : 1.00 mm Pitch, 12 cores, Length 300 mm.)
tray
tapering driver
cam (66)
1
Insert a tapering driver (3 mm in diameter)
in the hole at the bottom of the unit,
turn the cam (66) fully in the direction of arrow A.
in the hole at the bottom of the unit,
turn the cam (66) fully in the direction of arrow A.
A
MAIN board
(CN706)
(CN706)
DISPLAY board
(CN801)
(CN801)
Connect jig (extension cable J-8000-024-A)
to the DISPLAY board (CN801) and
MAIN board (CN706).
to the DISPLAY board (CN801) and
MAIN board (CN706).
6
SCD-XE670
SECTION 2
GENERAL
This section is extracted from
instruction manual.
instruction manual.
CHECK qg (18)
CLEAR qh (18)
Disc tray 6 (10)
Display w; (11)
MENU qj (10, 20)
MULTI/2CH qk (9, 11)
Multi-Channel indicator 7
PHONE LEVEL qf (25)
CLEAR qh (18)
Disc tray 6 (10)
Display w; (11)
MENU qj (10, 20)
MULTI/2CH qk (9, 11)
Multi-Channel indicator 7
PHONE LEVEL qf (25)
PHONES jack qd
PLAY MODE 2 (17, 18)
POWER 1 (10)
Remote sensor ql (6)
REPEAT 3 (16)
SACD/CD 5 (9, 11)
TIME/TEXT 4 (11)
PLAY MODE 2 (17, 18)
POWER 1 (10)
Remote sensor ql (6)
REPEAT 3 (16)
SACD/CD 5 (9, 11)
TIME/TEXT 4 (11)
Front Panel
Rear Panel
ANALOG 2CH OUT L/R jacks 1 (8)
ANALOG 5.1CH OUT jacks 2 (6)
DIGITAL (CD) OUT OPTICAL jack 3 (8)
Mains lead 4 (8)
DIGITAL (CD) OUT OPTICAL jack 3 (8)
Mains lead 4 (8)
BUTTON DESCRIPTIONS
lAMSL dial qs (10, 11, 14,
15, 19, 20)
A OPEN/CLOSE 8 (10, 18)
H 9 (10, 15, 16, 17, 18)
X 0 (11)
x qa (11, 16, 19)
m/M wa (15)
7
SCD-XE670
Remote Control
A
yB 8 (16)
AMS
./> qa (14, 15, 17,
22)
CHECK 9 (18)
CLEAR qk (18)
CONTINUE 2 (17, 18)
DISPLAY MODE 3 (12)
ENTER qj (22)
INDEX
CLEAR qk (18)
CONTINUE 2 (17, 18)
DISPLAY MODE 3 (12)
ENTER qj (22)
INDEX
>/. qd (15)
LEVEL ADJ ql (22)
MULTI/2CH qh (9, 11)
Number buttons 5 (14, 18)
PROGRAM qf (18)
REPEAT 7 (16)
SACD/CD qg (9, 11)
SHUFFLE 1 (17)
TIME/TEXT 4 (11)
MULTI/2CH qh (9, 11)
Number buttons 5 (14, 18)
PROGRAM qf (18)
REPEAT 7 (16)
SACD/CD qg (9, 11)
SHUFFLE 1 (17)
TIME/TEXT 4 (11)
BUTTON DESCRIPTIONS
>10 6 (14, 18)
H w; (10, 15, 16, 17, 18)
H w; (10, 15, 16, 17, 18)
X 0 (11)
x wa (11, 16, 19)
m/M qs (15)