DOWNLOAD Sony SCD-XB780 Service Manual ↓ Size: 6.17 MB | Pages: 84 in PDF or view online for FREE

3

The laser diode in the optical pick-up block may suffer electro-
static break-down because of the potential difference generated
by the charged electrostatic load, etc. on clothing and the human
body.
During repair, pay attention to electrostatic break-down and also
use the procedure in the printed matter which is included in the
repair parts.
The flexible board is easily damaged and should be handled with
care.

The laser beam on this model is concentrated so as to be focused
on the disc reflective surface by the objective lens in the optical
pick-up block. Therefore, when checking the laser diode emis-
sion, observe from more than 30 cm away from the objective lens.

In cleaning the lens of optical pick-up, use the air blower.
Never use a cotton swab for cleaning the lens of optical pick-up,
which otherwise causes a trouble.

tray

tapering driver

cam (66)

1

Insert a tapering driver (3 mm in diameter) 
in the hole at the bottom of the unit,
turn the cam (66) fully in the direction of arrow 

A

.

A

4

In checking the DISPLAY board, prepare jig (extension cable J-2501-200-A : 1.00 mm Pitch, 11 cores, Length 300 mm.)

MAIN board

DISPLAY board

CN801

Connect jig (extension cable J-2501-200-A)
to the DISPLAY board (CN801) and 
MAIN board (CN706).

CN706

 Follow the assembly procedure in the numerical order given.

3

four screws
(PTTWH3

 

×

 

6)

2

power transformer
(T902)

4

3

four screws
(PTTWH3

 

×

 

6)

1

power transformer
(T901)

5

Solder  seventeen portions.

Note : Solder the TRANS board after installing power transformers (T901, T902)

to the chassis.
(To prevent the TRANS board from being cracked.)

5

If the power is turned on with a disc loaded in the set, a sequence of operation as shown below will be performed.
(The operation varies depending on the type of disc)    Condition: continue mode

(1) CD
 1.

Sled reverse move (sled in)

 2.

Disc detect

 3.

IC setting for CD

 4.

Servo error signal offset auto adjustment

 5.

Spindle kick for LD on

 6.

LD on

 7.

Focus search

 8.

Focus servo on

 9.

Spindle kick

 10. Spindle servo on
 11. E-F balance auto adjustment
 12. Tracking & sled servo on
 13. Focus bias auto adjustment
 14. Focus servo gain auto adjustment
 15. Tracking servo gain auto adjustment
 16. Jump to lead-in area
 17. Read TOC
 18. Stop

(2) SACD (single layer)
 1.

Sled reverse move (sled in)

 2.

Disc detect

 3.

IC setting for SACD

 4.

Servo error signal offset auto adjustment

 5.

Spindle kick for LD on

 6.

LD on

 7.

Focus search

 8.

Focus servo on

 9.

Spindle kick

 10. Spindle servo on
 11. E-F balance auto adjustment
 12. Tracking & sled servo on
 13. Focus bias auto adjustment
 14. Focus servo gain auto adjustment
 15. Tracking servo gain auto adjustment
 16. Jump to lead-in area
 17. Read TOC
 18. Stop

(3) SACD (dual layer)
 1.

Sled reverse move (sled in)

 2.

Disc detect

 3.

IC setting for SACD

 4.

Servo error signal offset auto adjustment

 5.

Spindle kick for LD on

 6.

LD on

 7.

Focus search

 8.

Focus servo on (layer 0)

 9.

Spindle kick

 10. Spindle servo on
 11. E-F balance auto adjustment (layer 0)
 12. Tracking & sled servo on (layer 0)
 13. Focus bias auto adjustment (layer 0)
 14. Focus servo gain auto adjustment (layer 0)
 15. Tracking servo gain auto adjustment (layer 0)
 16. Jump to lead-in area
 17. Read TOC
 18. Focus jump (layer 0

tlayer 1)

 19. E-F balance auto adjustment (layer 1)
 20. Tracking & sled servo on (layer 1)
 21. Focus bias auto adjustment (layer 1)
 22. Focus servo gain auto adjustment (layer 1)
 23. Tracking servo gain auto adjustment (layer 1)
 24. Focus Jump (layer 1

tlayer 0)

 25. Stop

6

ANALOG

L

L

R

R

2CH OUT

5.1CH OUT

OUT

FRONT

COAXIAL OPTICAL

SURR

CENTER

SUB

WOOFER

DIGITAL(CD)

1

Connect to an audio component (stereo/2 channel)
using the audio connecting cord.

2

Connect to an amplifier equipped with the 5.1CH
input jacks (Multi-channel amplifier, AV amplifier,
etc.) using the audio connecting cords.

3

Connect to an audio component using the coaxial
digital cable.

4

Connect to an audio component using an optical
digital cable.

Note
Only the audio signals of the CD can be output from the
DIGITAL (CD) OUT connectors shown in 3 and 4. Those of the
Super Audio CD cannot be output through DIGITAL (CD) OUT.

This section is extracted from
instruction manual.

1

Press to turn on the player.

2

Each time you press the button, the playing time of the
track, the total remaining time on the disc, or TEXT
information appears in the display.

3

Each time you press the button while playing back a
hybrid disc, the layer to be played back switches
between the HD (Super Audio CD) layer and the CD
layer.

4

Press 

A OPEN/CLOSE to open/close the disc tray.

5

Multi-channel indicator
Turns on when you turn on the player, or when the
Multi-channel Super Audio CD is loaded and select
the Multi-channel playback area by pressing MULTI/
2CH.

6

A OPEN/CLOSE button
Press to open the disc tray.

7

H button
Press to start play.

8

X button
Press to pause play.

9

x button
Press to stop play.

0

l AMS L dial (AMS: Automatic Music Sensor)

When you turn the 

l AMS L dial

counterclockwise by one click, you go back to the
preceding track; when you turn the 

l AMS L

dial clockwise by one click, you go to the succeeding
track.

qa

PHONES
Connect the headphones.
During playback of a Multi-channel Super Audio CD,
the same signal that is output from the ANALOG
5.1CH FRONT L/R jacks is output from the PHONES
jack.

qs

PHONE LEVEL
Adjust the headphones volume.

qd

Press to enter the menu.
Press to exit from the menu and return to the normal
display.

qf

Press to select the playback area when the 2 channel +
Multi-channel Super Audio CD is loaded.

qg

Shows various information.

qh

m/M buttons
Press to locate a portion you want to play within a
track.