DOWNLOAD Sony SCD-XB770 Service Manual ↓ Size: 6.98 MB | Pages: 86 in PDF or view online for FREE

10

 Follow the disassembly procedure in the numerical order given.

1

two screws

3

cover

2

two flat head screws (TP)

2

two flat head screws (TP)

4

two washers
(DIA. 3.2)

5

two washers (P)

4

two washers (DIA. 3.2)

2

two flat head screws (TP)

2

loading panel assy

1

Pull out the tray.
(Refer to page 3, HOW TO 
OPEN THE TRAY WHEN 
POWER SWITCH TURNS 
OFF.)

6

two claws

4

connector 
(CN992)

7

front panel section

4

two connector
(CN305, 905)

3

wire (flat type) 
(12 core)
(CN706)

6

two claws

5

seven screws
(BV/RING)

11

3

five screws
(BVT/RING)

2

four connectors
(CN301, 304, 305, 306)

        

1

two wires 
(flat type) (19 core)
(CN302, 303)

7

AUDIO board

4

screw
(BVTT3

 

×

 

6)

5

two washers (DIA. 3.6)

0

three screws
(BVTT3

 

×

 

6)

6

PC board holder

8

wire (flat type)
(12 core) (CN706)

9

connector
(CN703)

0

screw
(BVTT3

 

×

 

6)

qs

MAIN board

qa

wiring stopper

9

two connectors
(CN704, 707)

8

wire (flat type)
(30 core) (CN708)

6

three screws
(BVTT3

 

×

 

8)

4

wire (flat type) (30 core)
(CN708)

7

mechanism deck
(CDM66B-DVBU6)

2

loading panel assy

5

connector (CN151)

1

Pull out the tray.
(Refer to page 3, HOW TO OPEN THE TRAY 
WHEN POWER SWITCH TURNS OFF.)

3

Push 
the tray.

12

1

screw (DIA. 12), floating

2

– BOTTOM VIEW –

3

base unit (DVBU-6)

base unit (DVBU-6)

cam (66)

13

The contents of test mode are as follows.

Wrong operation in the test mode causes a trouble, thus requiring extreme care.

LINE command (1X): Use mainly for a manufacturing line.

No.

Name

Description

Remarks

05

DSP MON1

XUGF, XPCK, C2PO outputted from IC509 (CD DSP)

Not used for the servicing

06

DSP MON2

MNT0, MNT1, MNT2, MNT3 outputted from IC509 (CD DSP)

Not used for the servicing

07

DSP MON3

RFCK, XPCK, XROF, GTOP outputted from IC509 (CD DSP)

Electrical measurement,
CD CLV jitter measurement

STANDARD command (1X): Use when the servo is applied by manual operation.

No.

Name

Description

Remarks

12

LD ON/OFF

The laser diode is turned on or off

On or off are switched alternately

13

SPIN ON/OFF

The spindle motor is rotated with the regulated voltage

On or off are switched alternately

14

FSRV ON/OFF

The focus servo is turned on or off

On or off are switched alternately

15

TSRV ON/OFF

The tracking servo is turned on or off

On or off are switched alternately

16

CLV ON/OFF

The spindle SLV servo is turned on or off

On or off are switched alternately

Focus and tracking servos must be already turned on

17

SSRV ON/OFF

The sled servo is turned on or off

On or off are switched alternately

Focus, tracking and spindle servos must be already turned on

18

ALL SRV ON

All servos are turned on

19

ALL SRV OFF

All servos are turned off

Stop command in the test mode

This set automatically executes self-diagnosis and various checks
by entering the test mode.

 This set automatically makes various adjustments according to the

type of disc, thereby not requiring adjustment of the set when parts
were replaced. However, be sure to execute 4-1. IC AND FLUO-
RESCENT DISPLAY TUBE CHECK, 4-2. AUTO CHECK and 4-
7. WAVEFORMS CHECK.

Various checks of this set require the following discs.

Model

Type 

*

1

Category

Application

MODEL
SATD-S5

12 cm disc

Adjusted value check,

(J-2501-215-A) SL

Reference disc

Operation check,

SATD-S4

Optical waveform check

(J-2501-184-A)

Not specified

DL

12 cm disc

Operation check

PATD-012

Adjusted value check,

(4-225-203-01)

CD

12 cm disc

Operation check,

YEDS-18

Reference disc

Optical waveform check

(3-702-101-01)

Not specified

HYBRID 12 cm disc

Operation check

*1 SL: Single Layer

DL: Dual Layer

Turn the 

[POWER]

 switch on while pressing the 

[        AMS        ]

dial and the 

[MENU]

 button. Release the 

[MENU]

 button and the

[        AMS        ]

 dial in this order when “Test Mode Menu” is

displayed on the fluorescent indicator tube. (If the 

[        AMS         ]

dial is released first, the test mode becomes active but “Test Mode
Menu” is not displayed)

To release the test mode, turn the 

[POWER]

 switch off.

To select and enter the “Test Mode Menu”, operate as follows.
1. Rotate the 

[        AMS        ]

 dial to select the menu, and press

the 

[        AMS        ]

 dial to enter.

2. The test is switched on or off alternately each time the

[        AMS        ]

 dial is pressed.

3. To return to the previous step, rotate the 

[        AMS        ]

 dial

to select the desired item, and press the 

[        AMS        ]

 dial

to enter.

l

L

l

L

l

L

l

L

l

L

l

L

l

L

l

L