DOWNLOAD Sony SCD-XA777ES Service Manual ↓ Size: 12.67 MB | Pages: 127 in PDF or view online for FREE

16

Procedure:
1. Press the 

[POWER]

 button while shorting the BP (TEST

MODE) on the PANEL board, and turn on the power so that
the following operations will be executed automatically.

1

Grid of all segments lights up sequentially starting from 1G
to 16G.

2

 The vertical line (total 5 lines) of all grids lights up sequen-

tially in the range of 3G to 16 G starting from the left.

3

 The horizontal line of (total 7 lines) of all grids lights up

sequentially in the range of 3G to 16G starting from the top.

4

 Grids from 5G to 6G go off.

2. With the machine in the status that is set in step 1-4, press

any on the remote commander. The grids 1G and 2G go off
and then the machine enters the key check standby state. (When
the 

[OPEN/CLOSE]

 key or the 

[  ]

 key is pressed, the recep-

tion check is canceled.)

3. After the key check is completed, turn JOG clockwise to turn

on the calendar segments sequentially. When the segment “20”
is confirmed, turn JOG counter-clockwise that turns off the
calendar segment. When the segment “1” is confirmed, this is
the end of check.

4. After all the checks are completed, confirm to see that the dis-

play  “!%%TEST-END!!%” appears. The message indicates
that the check is ended normally.

5. Press the 

[POWER]

 button to turn off the main power and

disconnect the power plug from the wall outlet.

x

IC1002

IC1001

R1081

BP (TEST MODE)

17

To release the test mode, turn the 

[POWER]

 switch off.

To select and enter the “TEST MODE Menu”, operate as follows.
1. Rotate the 

[        AMS        ]

 dial to select the menu, and press

the 

[        AMS        ]

 dial to enter.

2. The test is switched on or off alternately each time the

[        AMS        ]

 dial is pressed.

3. To return to the previous step, rotate the 

[        AMS        ]

 dial

to select the desired item, and press the 

[        AMS        ]

 dial

to enter.

The contents of test mode are as follows.

Wrong operation in the test mode causes a trouble, thus requiring extreme care.

LINE command (1X): Use mainly for a manufacturing line.

No.

Name

Description

Remarks

05

DSP MON1

XUGF, XPCK, C2PO outputted from IC509 (CD DSP)

Not used for the servicing

06

DSP MON2

MNT0, MNT1, MNT2, MNT3 outputted from IC509 (CD DSP)

Not used for the servicing

07

DSP MON3

RFCK, XPCK, XROF, GTOP outputted from IC509 (CD DSP)

Electrical measurement,
CD CLV jitter measurement

STANDARD command (1X): Use when the servo is applied by manual operation.

No.

Name

Description

Remarks

12

LD ON/OFF

The laser diode is turned on or off

On or off are switched alternately

13

SPIN ON/OFF

The spindle motor is rotated with the regulated voltage

On or off are switched alternately

14

FSRV ON/OFF

The focus servo is turned on or off

On or off are switched alternately

15

TSRV ON/OFF

The tracking servo is turned on or off

On or off are switched alternately

16

CLV ON/OFF

The spindle SLV servo is turned on or off

On or off are switched alternately

Focus and tracking servos must be already turned on

17

SSRV ON/OFF

The sled servo is turned on or off

On or off are switched alternately

Focus, tracking and spindle servos must be already turned on

18

ALL SRV ON

All servos are turned on

19

ALL SRV OFF

All servos are turned off

Stop command in the test mode

This set automatically executes self-diagnosis and various checks
by entering the test mode.

 This set automatically makes various adjustments according to the

type of disc, thereby not requiring adjustment of the set when parts
were replaced. However, be sure to execute 4-1. IC AND FLUO-
RESCENT DISPLAY TUBE CHECK, 4-2. AUTO CHECK and 4-
7. WAVEFORMS CHECK.

Various checks of this set require the following discs.

Model

Type 

*

1

Category

Application

MODEL
SATD-S5

12 cm disc

Adjusted value check,

(J-2501-215-A) SL

Reference disc

Operation check,

SATD-S4

Optical waveform check

(J-2501-184-A)

Not specified

DL

12 cm disc

Operation check

PATD-012

Adjusted value check,

(4-225-203-01)

CD

12 cm disc

Operation check,

YEDS-18

Reference disc

Optical waveform check

(3-702-101-01)

Not specified

HYBRID 12 cm disc

Operation check

*1 SL: Single Layer

DL: Dual Layer

Turn the 

[POWER]

 switch on while pressing the 

[        AMS        ]

dial and the 

[TIME/TEXT]

 button. Release the 

[TIME/TEXT]

 button

and the 

[        AMS        ]

 dial in this order when “TEST MODE

Menu” is displayed on the fluorescent display tube. (If the

[        AMS         ]

 dial is released first, the test mode becomes active

but “TEST MODE Menu” is not displayed)

l

L

l

L

l

L

l

L

l

L

l

L

l

L

l

L

18

FOCUS command (2X): Focus related. (All servos must be already turned on (except command 21))

No.

Name

Description

Remarks

21

FSRCH ON/OFF

The continuous vertical motion of the optical pick-up lens is turned on or

Avoid a long-time use

off

22

F-BIAS UP

Increase focus bias

Focus bias value

23

F-BIAS DOWN

Decrease focus bias

Focus bias value

24

ADJ FCSBIAS

The focus bias is adjusted automatically
Both + and - directions are searched to search for best jitter point

25

FGAIN UP/DW

The focus servo gain is switched between normal and down

Normal or down are switched alternately

26

FJMP UP/DWN

Focus jump is executed

Valid only for DL

UP: layer 0t1, DOWN: layer 1t0

27

FOCUS AGC

The focus servo gain is adjusted automatically

28

DISP FBdata

The focus bias adjusted value is displayed

Hexadecimal display 9 bit data

On or off and up or down are switched alternately

OFFSET (PI, FE, TE) command (3X): Adjusts the offset of PI, FE and TE signals.

No.

Name

Description

Remarks

31

PI/FE OFSET

Adjusts the offset of PI, FE and TE signals

TE offset adjustment is executed for the CD

This adjustment must be executed after 61 DISC DETECT

only

TRACKING command (4X): Tracking servo related.

No.

Name

Description

Remarks

41

TGAIN NM/UP

The tracking servo gain is switched between normal and up

Normal or up are switched alternately

44

ADJ TRK DSP

The traverse AGC and E-F balance adjustment is performed

45

TRACKING AGC

The tracking servo gain is adjusted automatically

SEARCH command (5X): Track search related. (Nos. 51 through 53 are not used for the servicing.)

No.

Name

Description

Remarks

51

1-TRCK JUMP

One-track jump is performed

52

M-TRCK MOVE

M-track movement is performed

53

FINE SEARCH

Fine search is performed

DISC DETECT command (6X): Disc type check related.

No.

Name

Description

Remarks

61

DISC DETECT

Disc type check is executed

Refer to how to apply servo by manual

Display after judgment

operation (19 page)

DSKMOD CD: Judged as CD
DSKMOD SL: Judged as SACD (SL)
DSKMOD DL: Judged as SACD (DL)
DSKMOD HLHD: Judged as HYBRID HD
DSKMOD CDRW: Judged as CD-RW

62

SET DISC CD

Enter disc type    CD setting

CD forced setting

63

SET DISC SL

Enter disc type    SL setting

SL forced setting

64

SET DISC DD

Enter disc type    DD setting

DD forced setting

65

SET DISC HH

Enter disc type    HYBRID HD setting

HD forced setting

66

SET DISC HC

Enter disc type    HYBRID CD setting

CD forced setting

19

TOOLS command (8X): Performs aging, reads adjusting parameters, etc.

No.

Name

Description

Remarks

81

VERSION

Firmware version is displayed

Example: Ver 1.00

83

TRAY AGING

Tray open-close aging is performed

Number of times and eccentricity

Not used for the servicing

measurement   Not used in this set.

84

JITTER

Jitter measurement

Not used for the servicing

85

ERROR RATE

Error rate measurement

Error rate

CD: C1, C2

Not used for the servicing

SACD: PO, PI1, PI2

86

ALL SRV ON

Apply all servos

Use when applying the servo by

Full automatic measurement including PI, FE and TE offset adjustment is

manual operation

performed

Refer to STANDARD command (17 page)

87

DISP ADJ DT

Automatic adjusting parameters are displayed

Refer to auto check items  (22 page)

The offset adjusted values are scroll-displayed in order of RF, VC, FE and
TE

Refer to auto check items  (22 page)

8d

Set Up Init

Set to factory shipping mode

Set when repair completed

PLAY, REPEAT, DIGIFIL, etc. are initialized

Refer to 4-6. SHIPPING MODE (26 page)

8F

49 TRCK JIT

Used for jitter measurement of 49th music on SACD-S4

For manufacturing line
Not used for the servicing

QA command (9X)

No.

Name

Description

Remarks

92

SET CHECK

The set is checked

Refer to 4-2. AUTO CHECK (22 page)

94

SET AGING

The set aging is performed

Refer to 4-5. AGING MODE (26 page)

Repeat by the specified number of times or until an error occurred

95

DISPLAY ERROR

The content of error recorded to the set is read and displayed
(Error recording) Only one item is recorded

96

D-OUT OnOff

Digital out of CD is turned on or off

Not used in this set.

98

APDO JITTER

Not used for the servicing

9C

BU DENCHO

The content of error recorded to the set is read, and then the S curve

Refer to 4-7.WAVEFORMS CHECK

waveform, traverse waveform, and RF waveform can be checked

(28 page)

successively

9D

P-ON HOUR

Approximate cumulative power supplying time is displayed

In unit of 1 hour

(Initialized by 8d command)

9E

RFD OUT

RFD output is turned on or off

Not used for the servicing

SACD jitter measuring mode

In analyzing failures of the set, the servo may be applied by manual operation. To apply servo in the test mode, use the following method.
1. After setting the test mode, rotate the 

[        AMS        ]

 dial to select a command, and press the 

[        AMS        ]

 dial to enter.

2. “61 DISC DETECT” (Disc type check)t“86 ALL SRV ON”  (All servos on + auto adjustment)
3. If applying servo while checking the condition one by one, “61 DISC DETECT” (Disc type check)t“31 PI/FE OFSET” (Offset

automatic adjustment)t“14 FSRV ON/OFF” (Focus servo on)t“16 CLV ON/OFF” (CLV servo on)t“44 ADJ TRK DSP ” (E-F
balance adjustment)t“15 TSRV ON/OFF” (Tracking servo on)t“17 SSRV ON/OFF” (Sled servo on)t“24 ADJ FCSBIAS” (Fo-
cus bias adjustment)t“27 FOCUS AGC” (Focus auto gain adjustment)t“45 TRACKING AGC” (Tracking auto gain adjustment).

1. On and off are alternately switched in the same command.
2. For a stop, select “19 ALL SRV OFF” and press the 

[        AMS        ]

 dial.

l

L

l

L

l

L