Sony SCD-XA333ES Service Manual ▷ View online
SCD-XA333ES
10
5
loading panel assy
4
bracket (loading panel)
3
two screws
(BVTP3
(BVTP3
×
10)
1
Insert a tapering driver in the hole
at the bottom of the unit,
turn the cover (CAM) fully in the
direction of arrow
at the bottom of the unit,
turn the cover (CAM) fully in the
direction of arrow
A
.
tapering driver
cover (CAM)
A
2
4
six screws
(BV3
(BV3
×
8)
7
front panel section
1
connector
(CN494)
(CN494)
1
connector
(CN480)
(CN480)
5
screw (BVTT3
×
8)
5
screw
(BVTT3
(BVTT3
×
8)
6
bracket (F)
3
connector
(CN400)
(CN400)
2
connector
(CN903)
(CN903)
6
bracket (F)
3-3.
LOADING PANEL ASSY
3-4.
FRONT PANEL SECTION
SCD-XA333ES
11
3-5.
MAIN BOARD
3-6.
MECHANISM DECK (CDM19IB-DVBU4B, CDM19IN-DVBU4B), RF BOARD
6
bracket (main)
5
two screws
(BVTT3
(BVTT3
×
8)
4
MAIN board
2
connector
(CN903)
(CN903)
2
connector
(CN701)
(CN701)
2
connector (CN907)
1
wire (flat type) (35 core)
(CN503)
(CN503)
1
wire (flat type) (19 core)
(CN902)
(CN902)
1
wire (flat type) (19 core)
(CN901)
(CN901)
5
two screws
(BVTT3
(BVTT3
×
8)
3
four screws (BVTT3
×
8)
A
2
two screws
(BVTT3
(BVTT3
×
8)
2
two screws
(BVTT3
(BVTT3
×
8)
8
mechanism deck
(CDM19IB-DVBU4B,
CDM19IN-DVBU4B)
(CDM19IB-DVBU4B,
CDM19IN-DVBU4B)
4
wire (flat type) (25 core)
(CN003)
(CN003)
5
connector
(CN002)
(CN002)
7
RF board
3
6
three screws
(BVTP2.6
(BVTP2.6
×
8)
1
Push the disc table in the
direction of arrow
direction of arrow
A
.
SCD-XA333ES
12
3-7.
DISC TABLE, BELT, LOADING MOTOR (M1)
3-8.
OPTICAL DEVICE (KHM-230AAA)
1
two screws
(BVTT M3 S)
(BVTT M3 S)
2
holder (A. P.) assy
9
disc table
8
guide bar (main)
6
bracket (disc table)
5
tapping screw
0
gear (P)
qf
four claws
qg
loading motor (M1)
3
Insert a tapering driver in the
hole of the cover (CAM) and
turn fully in the direction of
arrow
hole of the cover (CAM) and
turn fully in the direction of
arrow
A
.
cover (CAM)
taper driver
A
qa
gear (C)
qs
belt
qd
two screws
(P3
(P3
×
3)
4
7
2
holder (A. P.) assy
7
stopper
4
Draw out the disc table fully
in the arrow
in the arrow
B
direction.
7
stopper
7
stopper
7
stopper
0
optical device (KHM-230AAA)
6
screw
(BVTP2.6
(BVTP2.6
×
8)
6
screw
(BVTP2.6
(BVTP2.6
×
8)
6
screw
(BVTP2.6
(BVTP2.6
×
8)
6
screw
(BVTP2.6
(BVTP2.6
×
8)
9
insulator
9
insulator
9
insulator
9
insulator
5
wire (flat type) (25 core)
(CN003)
(CN003)
8
qa
two cone type coil spring (230)
qa
two cone type coil spring (230)
3
Insert a tapering driver in the
hole of the cover (CAM) and
turn fully in the direction of
arrow
hole of the cover (CAM) and
turn fully in the direction of
arrow
A
.
cover (CAM)
taper driver
A
B
1
two screws
(BVTT M3 S)
(BVTT M3 S)
SCD-XA333ES
13
3-9.
BASE UNIT (DVBU4B)
1
two claws
1
two claws
S002
S001
cover (CAM)
2
Up the SWITCH board in the
direction of arrow
direction of arrow
A
.
Note: Take care not to break the shaft of
the switch (S001, S002) when raising
the SWITCH board.
the SWITCH board.
A
C
B
4
limiter (L)
3
screw
(BVTT3
(BVTT3
×
6)
5
screw
(BVTT3
(BVTT3
×
6)
6
limiter (R)
7
Insert a taper driver into the cover (CAM),
and rotate in the arrow
and rotate in the arrow
B
direction to raise
the base unit (DVBU4B) in the arrow
C
direction.
(Chuck release state)
8
yoke bracket
0
roller (L)
9
base unit (DVBU4B)
chassis (outseat)
Click on the first or last page to see other SCD-XA333ES service manuals if exist.