Sony SCD-C555ES Service Manual ▷ View online
8
SCD-C555ES
3-6. CD MECHANISM DECK (CDM59-DVBU5)
3
four screws
(BVTP3
(BVTP3
×
8)
5
seven screws
(BVTP3
(BVTP3
×
8)
6
two screws
(BVTP3
(BVTP3
×
8)
4
D-POWER board
7
I/O board
1
Connector
(CN401)
2
Connector
(CN400)
2
five screws
(BVTP3
(BVTP3
×
8)
3
sub chassis
1
five screws
(BVTP3
(BVTP3
×
8)
4
three screws
(BVTP3
(BVTP3
×
8)
6
screw
(BVTP3
(BVTP3
×
8)
5
Slide the tray until the screw
that fixes the table assy can be
seen through around hole
in the table assy.
that fixes the table assy can be
seen through around hole
in the table assy.
a
7
screw(BVTP3
×
8)
8
CD mechanism deck
(CDM59-DVBU5)
(CDM59-DVBU5)
a
3-5. D-POWER, I/O BOARD
9
SCD-C555ES
3-7. OPTICAL PICK-UP BLOCK (KHM-230AAA/J1NP)
3
two screws
(PTPWH M2.6)
(PTPWH M2.6)
3
two screws
(PTPWH M2.6)
(PTPWH M2.6)
4
optical pick-up block
(KHM-230AAA/J1NP)
5
four compression springs
2
1
two screws
(PTPWH M2.6)
(PTPWH M2.6)
BU section
Note: When installing the BU
on the chassis, set the
lever (lifter) in free
position, the gear (U/D)
in UP position, and insert
the shaft into the
groove of gear (U/D).
lever (lifter) in free
position, the gear (U/D)
in UP position, and insert
the shaft into the
groove of gear (U/D).
gear (U/D)
b
b
6
connector
(CN002)
(CN002)
7
three screws
(BVTP2.6
(BVTP2.6
×
8)
8
RF board
3-8. TABLE ASSY
Note: When installing the table assy
on the chassis assy, engage
the gear (loading C) with the groove
by looking into the gear through
a hole in the table assy.
the gear (loading C) with the groove
by looking into the gear through
a hole in the table assy.
qa
table assy
9
three screws
(BTTP M2.6)
(BTTP M2.6)
e
c
c
d
d
e
0
bracket (guide)
gear
(loading C)
(loading C)
7
two screws
(BTTP M2.6)
(BTTP M2.6)
5
three screws
(BTTP M2.6)
(BTTP M2.6)
6
bracket (guide)
2
two screws
(BVTP 3
(BVTP 3
×
8)
1
Slide the tray until the screw
that fixes the bracket (guide)
can be seen through a round
hole , in the table assy.
that fixes the bracket (guide)
can be seen through a round
hole , in the table assy.
3
8
bracket (guide 2)
4
wire (flat type)
(6 core) (CN15)
(6 core) (CN15)
10
SCD-C555ES
3
two screws
(BTTP M2.6)
(BTTP M2.6)
4
LOADING MOTOR board
1
belt (loading)
2
connector
(CN13)
(CN13)
3-10. LOADING MOTOR BOARD
3-9. TRAY, SENSOR BOARD
1
screw
(PTPWH M2.6)
(PTPWH M2.6)
3
belt (rotary)
4
two screws
(BTTP M2.6)
(BTTP M2.6)
4
two screws
(BTTP M2.6)
(BTTP M2.6)
5
SENSOR board
2
tray
11
SCD-C555ES
3-11. ADJUSTING PHASE OF SWING GEAR AND GEAR (U/D)
6
screw
(PTPWH M2.6)
(PTPWH M2.6)
5
stopper washer (FR)
4
Push fully the shaft of gear (shaft) and
align the hole shape of gear (loading B).
align the hole shape of gear (loading B).
3
Let the swing gear through under the
chassis and engage its dowel
with the groove of rotary encoder.
chassis and engage its dowel
with the groove of rotary encoder.
2
Install the rotary encoder so that
its groove comes to the position
shown in the figure.
its groove comes to the position
shown in the figure.
1
Insert the gear (shaft) up to the
position where its shaft comes
out by 5 mm.
position where its shaft comes
out by 5 mm.
g
g
h
h
f
f
f
7
gear (U/D)
8
screw
(PTPWH M2.6)
(PTPWH M2.6)
q;
screw
(PTPWH M2.6)
(PTPWH M2.6)
circle mark
circle mark
swing gear
gear (RV)
Fig. A
9
gear (RV)
Note: Align swing gear, a circle mark
Note: Align swing gear, a circle mark
on the gear (U/D), and the teeth
of gear (RV) to the position
showing in the Fig. A.
of gear (RV) to the position
showing in the Fig. A.
Click on the first or last page to see other SCD-C555ES service manuals if exist.