Sony SAVA-500 / SS-CN16 / SS-SR16 Service Manual ▷ View online
4
SECTION 2
GENERAL
• LOCATION OF CONTROLS
Main Unit (L-ch)
– Front View –
– Front View –
1 INPUT button
2 SURROUND button
3 CENTER MODE button
4 S. WOOFER button
5 MASTER VOL +/– buttons
6 STANDBY, ON, READY indicators
7 U button
2 SURROUND button
3 CENTER MODE button
4 S. WOOFER button
5 MASTER VOL +/– buttons
6 STANDBY, ON, READY indicators
7 U button
1 TV IN jack
2 VIDEO IN jack
3 AUX IN jack
4 5.1CH INPUT (FRONT, REAR, WOOFER, CENTER) jack
5 CONTROL S, TV IN jack (US, Canadian models)
6 WIRELESS REAR SPEAKER jack
7 CENTER SPEAKER terminal
8 REAR SPEAKERS terminal
9 R-ch SPEAKER OUTPUT connector
2 VIDEO IN jack
3 AUX IN jack
4 5.1CH INPUT (FRONT, REAR, WOOFER, CENTER) jack
5 CONTROL S, TV IN jack (US, Canadian models)
6 WIRELESS REAR SPEAKER jack
7 CENTER SPEAKER terminal
8 REAR SPEAKERS terminal
9 R-ch SPEAKER OUTPUT connector
– Rear View –
2 3 4
1
5
6
7
1
2
3
2
3
4
5
6
7
8
9
9
5
AMPLIFIER SECTION
Note:
Follow the disassembly procedure in the numerical order given.
SECTION 3
DISASSEMBLY
2
grille frame (A)
ass’y
ass’y
3
screw
(BVTT4
(BVTT4
×
25)
6
screw
(BVTT4
(BVTT4
×
25)
4
washer
(BF)
(BF)
5
washer
(S)
(S)
L-ch speaker section
7
flat wire
(CN503)
(CN503)
8
connector
(CN907)
(CN907)
1
grille frame (B) ass’y
!º
five screws
(BVTP3
(BVTP3
×
8)
!™
connector
!£
Remove the amplifier
section in arrow
section in arrow
B
direction.
!¡
Remove the panel (L/B)
in arrow
in arrow
A
direction.
9
eleven screws
(4
(4
×
20)
B
A
6
SERVICE POSITION
2
two screws
(transistor)
(transistor)
!¡
eleven screws
(BVTP3
(BVTP3
×
8)
5
heatsink and
AMP board
AMP board
7
bracket
6
two screws
(BVTP3
(BVTP3
×
8)
8
connector
(CN371)
(CN371)
6
screw
(BVTP3
(BVTP3
×
8)
4
two connectors
(CN601, 603)
(CN601, 603)
!º
connector
!™
back panel (L/A)
1
Remove the amplifier section. (Refer to page 5)
3
two screws
(BVTP3
(BVTP3
×
8)
9
cord bushing
!£
two screws
(BVTP3
(BVTP3
×
8)
A
!¢
Erect the MAIN boad
in arrow
in arrow
A
direction.
!£
two screws
(BVTP3
(BVTP3
×
8)
!£
four screws
(BVTP3
(BVTP3
×
8)
7
!ª
Connect the power SW
lead wire to STANDBY
board connector (CN907).
lead wire to STANDBY
board connector (CN907).
@º
Connect the flat wire to
DISPLAY board connector (CN503).
DISPLAY board connector (CN503).
@™
Push the power SW.
@¡
Connect the MAIN board
and chassis with
two clip wires.
and chassis with
two clip wires.
bracket
MAIN board
!∞
Insert an insulation sheet
between chassis and
MAIN board.
between chassis and
MAIN board.
!•
Connect the fan motor lead wire
to MAIN board connector (CN371).
to MAIN board connector (CN371).
heatsink
!¶
Insert two connectors
(CN601, 603) into
the connectors
(CN301, 911) on
the MAIN board.
(CN601, 603) into
the connectors
(CN301, 911) on
the MAIN board.
!§
Attach the bracket
to the heatsink
with two screws.
to the heatsink
with two screws.
chassis