Sony SA-WFS3 / SS-FS3 Service Manual ▷ View online
SA-WFS3/SS-FS3
2
1.
SERVICING NOTES
............................................. 3
2. DISASSEMBLY
2-1. Disassembly
Flow
........................................................... 4
2-2. AMP
Block
..................................................................... 4
2-3. Front Panel Block ........................................................... 5
2-4. Bracket
2-4. Bracket
(TOP)
................................................................. 7
2-5. S-AIR Board, Tuner (FM/AM) ....................................... 7
2-6. HDMI
2-6. HDMI
Board
................................................................... 8
2-7. MAIN
Board
................................................................... 9
2-8. POWER
Board
................................................................ 9
3.
TEST MODE
............................................................ 10
4. DIAGRAMS
4-1. Block Diagram - HDMI Section - ................................... 12
4-2. Block Diagram - INPUT Section - .................................. 13
4-3. Block Diagram - DSP Section - ...................................... 14
4-4. Block Diagram - AMP, PANEL Section - ....................... 15
4-5. Block Diagram - POWER SUPPLY Section - ................ 16
4-6. Schematic Diagram - HDMI Board (1/2) - ..................... 18
4-7. Schematic Diagram - HDMI Board (2/2) - ..................... 19
4-8. Printed Wiring Board - HDMI Board - ........................... 20
4-9. Printed Wiring Board - IO Section - ............................... 21
4-10. Schematic Diagram - IO-DIGITAL Board - ................... 22
4-11. Schematic Diagram - S-AIR Board - .............................. 23
4-12. Printed Wiring Board
4-2. Block Diagram - INPUT Section - .................................. 13
4-3. Block Diagram - DSP Section - ...................................... 14
4-4. Block Diagram - AMP, PANEL Section - ....................... 15
4-5. Block Diagram - POWER SUPPLY Section - ................ 16
4-6. Schematic Diagram - HDMI Board (1/2) - ..................... 18
4-7. Schematic Diagram - HDMI Board (2/2) - ..................... 19
4-8. Printed Wiring Board - HDMI Board - ........................... 20
4-9. Printed Wiring Board - IO Section - ............................... 21
4-10. Schematic Diagram - IO-DIGITAL Board - ................... 22
4-11. Schematic Diagram - S-AIR Board - .............................. 23
4-12. Printed Wiring Board
- ANALOG-POMODORO Board - ................................ 24
4-13. Schematic Diagram
- ANALOG-POMODORO Board - ................................ 25
4-14. Printed Wiring Board
- MAIN Board (Component Side) - ................................ 26
4-15. Printed Wiring Board
- MAIN Board (Conductor Side) - .................................. 27
4-16. Schematic Diagram - MAIN Board (1/6) - ..................... 28
4-17. Schematic Diagram - MAIN Board (2/6) - ..................... 29
4-18. Schematic Diagram - MAIN Board (3/6) - ..................... 30
4-19. Schematic Diagram - MAIN Board (4/6) - ..................... 31
4-20. Schematic Diagram - MAIN Board (5/6) - ..................... 32
4-21. Schematic Diagram - MAIN Board (6/6) - ..................... 33
4-22. Printed Wiring Boards - KEY, SPEAKER Section - ...... 34
4-23. Schematic Diagram - KEY, SPEAKER Section - ........... 35
4-24. Printed Wiring Board - DISPLAY Board - ..................... 36
4-25. Schematic Diagram - DISPLAY Board - ........................ 37
4-26. Printed Wiring Board - POWER Board - ........................ 38
4-27. Schematic Diagram - POWER Board - .......................... 39
4-17. Schematic Diagram - MAIN Board (2/6) - ..................... 29
4-18. Schematic Diagram - MAIN Board (3/6) - ..................... 30
4-19. Schematic Diagram - MAIN Board (4/6) - ..................... 31
4-20. Schematic Diagram - MAIN Board (5/6) - ..................... 32
4-21. Schematic Diagram - MAIN Board (6/6) - ..................... 33
4-22. Printed Wiring Boards - KEY, SPEAKER Section - ...... 34
4-23. Schematic Diagram - KEY, SPEAKER Section - ........... 35
4-24. Printed Wiring Board - DISPLAY Board - ..................... 36
4-25. Schematic Diagram - DISPLAY Board - ........................ 37
4-26. Printed Wiring Board - POWER Board - ........................ 38
4-27. Schematic Diagram - POWER Board - .......................... 39
5.
EXPLODED VIEWS
5-1. Cabinet Section (SA-WFS3) ........................................... 56
5-2. Front Panel Section (SA-WFS3) ..................................... 57
5-3. AMP Section (SA-WFS3) ............................................... 58
5-4. Main Section (SA-WFS3) ............................................... 59
5-5. Chassis Section (SA-WFS3) ........................................... 60
5-6. SS-FS3
5-2. Front Panel Section (SA-WFS3) ..................................... 57
5-3. AMP Section (SA-WFS3) ............................................... 58
5-4. Main Section (SA-WFS3) ............................................... 59
5-5. Chassis Section (SA-WFS3) ........................................... 60
5-6. SS-FS3
............................................................................ 61
6.
ELECTRICAL PARTS LIST
.............................. 62
Accessories are given in the last of the electrical parts list.
TABLE OF CONTENTS
NOTES ON CHIP COMPONENT REPLACEMENT
•
•
Never reuse a disconnected chip component.
•
Notice that the minus side of a tantalum capacitor may be dam-
aged by heat.
aged by heat.
SAFETY-RELATED COMPONENT WARNING!
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE
WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN
THE PARTS LIST ARE CRITICAL TO SAFE OPERATION.
REPLACE THESE COMPONENTS WITH SONY PARTS
WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN
THE PARTS LIST ARE CRITICAL TO SAFE OPERATION.
REPLACE THESE COMPONENTS WITH SONY PARTS
WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS
MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.
MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.
Note: Refer to page 61 for information of SS-FS3.
SA-WFS3/SS-FS3
3
SECTION 1
SERVICING NOTES
UNLEADED SOLDER
Boards requiring use of unleaded solder are printed with the lead-
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
Boards requiring use of unleaded solder are printed with the lead-
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size)
: LEAD FREE MARK
Unleaded solder has the following characteristics.
• Unleaded solder melts at a temperature about 40 °C higher
• Unleaded solder melts at a temperature about 40 °C higher
than ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350 °C.
Caution: The printed pattern (copper foil) may peel away if
about 350 °C.
Caution: The printed pattern (copper foil) may peel away if
the heated tip is applied for too long, so be careful!
• Strong
viscosity
Unleaded solder is more viscous (sticky, less prone to fl ow)
than ordinary solder so use caution not to let solder bridges
occur such as on IC pins, etc.
than ordinary solder so use caution not to let solder bridges
occur such as on IC pins, etc.
• Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.
also be added to ordinary solder.
• JIG
When disassembling the set, use the following jig (for speaker
When disassembling the set, use the following jig (for speaker
removal).
Part No. J-2501-238-A JIG FOR SPEAKER REMOVAL
NOTE OF CONFIRMING THE BOARDS (SA-WFS3)
Protecting is generated when energizing with the heat sink de-
tached. Fix the heat sink to the MAIN board by using the screw
and the nut without fail when you confi rm the board.
Protecting is generated when energizing with the heat sink de-
tached. Fix the heat sink to the MAIN board by using the screw
and the nut without fail when you confi rm the board.
CONFIRMING THE POWER BOARD (SA-WFS3)
The POWER board can be confi rmed by removing the bottom
plate of the active subwoofer.
The POWER board can be confi rmed by removing the bottom
plate of the active subwoofer.
NOTE THE IC3511 AND IC3513 ON THE HDMI BOARD
REPLACING (SA-WFS3)
IC3511 and IC3513 on the HDMI board cannot exchange with sin-
gle. When these parts are damaged, exchange the entire mounted
board.
REPLACING (SA-WFS3)
IC3511 and IC3513 on the HDMI board cannot exchange with sin-
gle. When these parts are damaged, exchange the entire mounted
board.
NOTE OF REPLACING THE IC340 AND IC400 ON
THE MAIN BOARD AND THE COMPLETE MAIN
BOARD (SA-WFS3)
When IC340 and IC400 on the MAIN board and the complete
MAIN board are replaced, it is necessary to spread the compound
(OIL COMPOUND G777) (Part No. J-2501-335-A ) between the
main board and the heat sink.
Spread the compound referring to the fi gure below.
THE MAIN BOARD AND THE COMPLETE MAIN
BOARD (SA-WFS3)
When IC340 and IC400 on the MAIN board and the complete
MAIN board are replaced, it is necessary to spread the compound
(OIL COMPOUND G777) (Part No. J-2501-335-A ) between the
main board and the heat sink.
Spread the compound referring to the fi gure below.
oil compound G777
(J-2501-335-A)
(J-2501-335-A)
IC340
IC400
– MAIN Board (Component Side) –
CAPACITOR ELECTORICAL DISCHARGE
PROCESSING (SA-WFS3)
When checking the board, for the electric shock prevention, con-
nect the resistors to both ends of respective capacitor (C903) to
discharge the capacitor (C903).
PROCESSING (SA-WFS3)
When checking the board, for the electric shock prevention, con-
nect the resistors to both ends of respective capacitor (C903) to
discharge the capacitor (C903).
C903
800
:/2 W
– POWER Board (Conductor Side) –
SA-WFS3/SS-FS3
4
SECTION 2
DISASSEMBLY
• This set can be disassembled in the order shown below.
• SA-WFS3 only is described in this section.
• SA-WFS3 only is described in this section.
2-1. DISASSEMBLY FLOW
Note: Follow the disassembly procedure in the numerical order given.
2-2. AMP BLOCK
2-2. AMP
BLOCK
(Page
4)
SET
2-3. FRONT PANEL BLOCK
(Page
(Page
5)
2-4. BRACKET
(TOP)
(Page
7)
2-5. S-AIR BOARD, TUNER (FM/AM)
(Page
(Page
7)
2-6. HDMI
BOARD
(Page
8)
2-7. MAIN
BOARD
(Page
9)
2-8. POWER
BOARD
(Page
9)
1 five screws (BVTT4 u 20)
3 connector
(CN562)
5 wire (flat type)
(15 core) (CN1001)
4 cushion
(saranet-A)
2
6 AMP block
SA-WFS3/SS-FS3
5
2-3. FRONT PANEL BLOCK
Note:
Work after laying the set sideways.
4
2 Insert the jig (J-2501-238-A) into a space
made by inserting the screwdriver,
and raise the front panel assy gradually.
2 Insert the jig (J-2501-238-A) into a space
made by inserting the screwdriver,
and raise the front panel block gradually.
3 Raise the front panel block a little by little
from bottom to top of the set.
eight bosses
bottom side
1 Insert a flat-head screwdriver into a recess
in the bottom of the set
to raise the front panel assy a little.
5 front panel block