Sony SA-WCT500 / SS-CT500 Service Manual ▷ View online
SA-WCT500/SS-CT500
10
2-6. D-VIDEO BOARD
Note: Arrange it when assembling it so that
the harness should not come in contact
with the heatsink.
– Top view –
5 two screws
(BVTP3
u 8)
clamp
2 connector
(CN3506)
1 wire (flat type)
(23 core) (CN3000)
qa D-VIDEO board
3 connector
(CN3202)
4 seven screws (BVTT3 u 6)
6 three screws (BVTP3 u 8)
7 bracket (HDMI FR)
8 two HS holders
9 heatsink (S58F)
0 radiation sheet (F)
heatsink
harness
SA-WCT500/SS-CT500
11
2-7. MAIN BOARD
2-8. POWER BOARD
4 wire (flat type)
(25 core) (CN1014)
1 two screws (BVTP3 u 8)
3 wire (flat type)
(7 core) (CN1011)
5 connector
(CN521)
6 two connectors
(CN541, CN564)
7 two connectors
(CN566,
CN1006)
2 bracket (HDMI RR)
8 three screws (BVTP3 u 16)
9 heatsink (DDV)
0 six screws (BVTP3 u 8)
qa wire (flat type) (9 core) (CN1013)
(US, Canadian, Saudi Arabia models),
wire (flat type) (11 core) (CN1012)
(AEP, Russian, UK models)
qs wire (flat type)
(23 core) (CN1017)
qd wire (flat type)
(19 core) (CN1005)
qf MAIN board
8 bracket (power) block
3 twelve screws
(BVTP3
u 8)
1 connector
(CN1006)
qa POWER board
2 two screws
(BVTP3
u 8)
4 connector
(CN904)
5 power cord connector
(CN901)
6 nine screws
(BVTP3
u 8)
7 two PC board holders
9 fuse (F901)
(US, Canadian)
0 fuse rating label
Note: When MAIN board is replaced, spread the
compound referring to “NOTE OF RE-
PLACING THE IC340 AND IC400 ON THE
MAIN BOARD AND THE COMPLETE MAIN
BOARD” on servicing notes (page 4).
PLACING THE IC340 AND IC400 ON THE
MAIN BOARD AND THE COMPLETE MAIN
BOARD” on servicing notes (page 4).
SA-WCT500/SS-CT500
12
SECTION 3
TEST MODE
1. TEST MODES OTHER THAN THE TEST MENU
These are executable test mode even if not entering the test menu.
These are executable test mode even if not entering the test menu.
1-1. Cold Reset
Procedure:
1. Press the [
Procedure:
1. Press the [
?/1
] button to turn the power on.
2. Press the three buttons [INPUT SELECTOR], [VOLUME –]
and [
?/1
] simultaneously.
3. The message “COLD RESET” appears on the fl uorescent indi-
cator tube, then turn the power off.
1-2. AM Step Change (SA-WCT500: US and Canadian
models)
Procedure:
1. Press the [
1. Press the [
?/1
] button to turn the power on.
2. Press the [INPUT SELECTOR] button to select the “TUNER
AM”.
3. Press the [
?/1
] button to turn the power off.
4. While pressing the [INPUT SELECTOR] button, press the
[
?/1
] button.
5. It turns power on and display “AM 9k Step” or “AM 10k
Step”, and thus the tuning interval is changed over.
2. TEST MODES IN THE TEST MENU
These are the test modes done in the test menu.
Prepare the remote commander (RM-ANP037) of the attachment
for this set.
These are the test modes done in the test menu.
Prepare the remote commander (RM-ANP037) of the attachment
for this set.
Setting method of the test menu:
1. Press the [
1. Press the [
?/1
] button to turn the power on.
2. Press the button in order of the [RETURN]
→ [ENT] → [0]
→ [1] → [0] → [SOUND FIELD] on the remote commander
(Make the interval when each button is pressed within two sec-
onds).
onds).
3. The message “TEST MENU” appears on the fl uorescent indi-
cator tube and enter the test menu.
2-1. Panel test Mode
Procedure:
1. Enter the test menu.
2. Press the [V] and [v] buttons on the remote commander to
Procedure:
1. Enter the test menu.
2. Press the [V] and [v] buttons on the remote commander to
select the “PANEL”, and press the [ENT] button.
3. All segments in the fl uorescent indicator tube are lighted up.
And half segments in the fl uorescent indicator tube are lighted
up, others half segments in the fl uorescent indicator tube are
lighted up, then all segments in the fl uorescent indicator tube
are lighted up. These operation is repeated.
up, others half segments in the fl uorescent indicator tube are
lighted up, then all segments in the fl uorescent indicator tube
are lighted up. These operation is repeated.
4. When all segments in the fl uorescent indicator tube are lighted
up in the state of step 3, press the [VOLUME +] button on the
remote commander and model information is displayed on the
fl uorescent indicator tube.
remote commander and model information is displayed on the
fl uorescent indicator tube.
Each time the [VOLUME +] button on the remote commander
is pressed, the display changes from destination information,
MC version, SYS version, UI version, ST version, TA version,
DSP version, TM version, CLA version, CEC version, SAIR
version in this order, and returns to the model information dis-
play.
is pressed, the display changes from destination information,
MC version, SYS version, UI version, ST version, TA version,
DSP version, TM version, CLA version, CEC version, SAIR
version in this order, and returns to the model information dis-
play.
5. In the state of step 3, press the [VOLUME –] button on the
remote commander and “K 0” is displayed on the fl uorescent
indicator tube.
indicator tube.
“K 0” value increases whenever a button on the set is pressed.
However, once a button has been pressed, it is no longer taken
into account.
However, once a button has been pressed, it is no longer taken
into account.
All buttons on the set is pressed, “OK” and “K 4” are alter-
nately displayed on the fl uorescent indicator tube.
nately displayed on the fl uorescent indicator tube.
6. To release from this mode, press the [
?/1
] button.
2-2. AMP Test Mode
Not used for the servicing.
Press the [
Not used for the servicing.
Press the [
?/1
] button if having entered this mode.
2-3. Tuner Factory Preset Change
Not used for the servicing.
Press the [
Not used for the servicing.
Press the [
?/1
] button if having entered this mode.
2-4. Tone Test Check
Procedure:
1. Enter the test menu.
2. Press the [V] and [v] buttons on the remote commander to
Procedure:
1. Enter the test menu.
2. Press the [V] and [v] buttons on the remote commander to
select the “TONE TEST”, and press the [ENT] button on the
remote commander.
remote commander.
3. The output speaker is displayed on the fl uorescent indicator
tube. At this time, the audio output check from each speaker is
possible.
possible.
4. To release from this mode, press the [
?/1
] button.
2-5. VACS Level Display On/off Change
Not used for the servicing.
Press the [
Not used for the servicing.
Press the [
?/1
] button if having entered this mode.
2-6. VACS On/off Change
Not used for the servicing.
Press the [
Not used for the servicing.
Press the [
?/1
] button if having entered this mode.
2-7. DSP Halt Mode
Not used for the servicing.
Press the [
Not used for the servicing.
Press the [
?/1
] button if having entered this mode.
2-8. DSP Status Display Mode
Not used for the servicing.
Press the [
Not used for the servicing.
Press the [
?/1
] button if having entered this mode.
2-9. DSP RAM Read/write Mode
Not used for the servicing.
Press the [
Not used for the servicing.
Press the [
?/1
] button if having entered this mode.
2-10. Video
μ-com Version Display
Procedure:
1. Enter the test menu.
2. Press the [V] and [v] buttons on the remote commander to
1. Enter the test menu.
2. Press the [V] and [v] buttons on the remote commander to
select the “VUCOM XXXX” (XXXX: video
μ-com version).
2-11. Faroudja Version Display
Procedure:
1. Enter the test menu.
2. Press the [V] and [v] buttons on the remote commander to
Procedure:
1. Enter the test menu.
2. Press the [V] and [v] buttons on the remote commander to
select the “FARO XXXX” (XXXX: faroudja version).
2-12. Faroudja Halt Mode
Not used for the servicing.
Press the [
Not used for the servicing.
Press the [
?/1
] button if having entered this mode.
2-13. Video
μ-com Halt Mode
Not used for the servicing.
Press the [
Press the [
?/1
] button if having entered this mode.
2-14. Video Calibration Setting
The brightness adjustment and the level adjustment of analog vid-
eo are adjusted by the automatic operation.
When the D-VIDEO board is exchanged, it is necessary to execute
this mode.
Refer to “VIDEO CALIBRATION ADJUSTMENT” in “4. ELEC-
TRICAL ADJUSTMENTS” for details.
The brightness adjustment and the level adjustment of analog vid-
eo are adjusted by the automatic operation.
When the D-VIDEO board is exchanged, it is necessary to execute
this mode.
Refer to “VIDEO CALIBRATION ADJUSTMENT” in “4. ELEC-
TRICAL ADJUSTMENTS” for details.
Ver. 1.1
SA-WCT500/SS-CT500
SA-WCT500/SS-CT500
13
13
2-15. Digital Media Port Test Mode
Not used for the servicing.
Press the [
Not used for the servicing.
Press the [
?/1
] button if having entered this mode.
2-16. Digital Media Device Port Test Mode
Note: Execute this mode after connecting the digital media port device
with this set.
Procedure:
1. Enter the test menu.
2. Press the [V] and [v] buttons on the remote commander to se-
1. Enter the test menu.
2. Press the [V] and [v] buttons on the remote commander to se-
lect the “DMPORT DEV”, and press the [ENT] button on the
remote commander.
remote commander.
3. The digital media port adaptor enter to the test mode. The op-
eration of the test mode is different according to each adaptor.
4. To release from this mode, press the [
?/1
] button.
2-17. S-AIR Test Mode
Procedure:
1. Enter the test menu.
2. Press the [V] and [v] buttons on the remote commander to
Procedure:
1. Enter the test menu.
2. Press the [V] and [v] buttons on the remote commander to
select the “S-AIR TEST”, and press the [ENT] button on the
remote commander.
remote commander.
3. The message “I2C” appears on the fl uorescent indicator tube
and enter the S-AIR test mode.
4. Press the [V] and [v] buttons on the remote commander to
select the “I2C”, and press the [ENT] button on the remote
commander.
commander.
The message “OK” or “NG” appears on the fl uorescent indica-
tor tube and the connection of the I2C line between DARR and
m-com can be confi rmed.
tor tube and the connection of the I2C line between DARR and
m-com can be confi rmed.
“OK” : Connection OK.
“NG” : Connection NG.
Press the [ENT] button on the remote commander, return to
item selection screen.
item selection screen.
5. Press the [V] and [v] buttons on the remote commander to
select the “QUALITY”, and press the [ENT] button on the re-
mote commander.
mote commander.
The quality of the communication is displayed on the fl uores-
cent indicator tube.
cent indicator tube.
Press the [ENT] button on the remote commander, return to
item selection screen.
item selection screen.
6. Press the [V] and [v] buttons on the remote commander to se-
lect the “POWER”, and press the [ENT] button on the remote
commander.
commander.
The output power is displayed on the fl uorescent indicator tube.
In this state, whenever the [V] and [v] buttons on the remote
In this state, whenever the [V] and [v] buttons on the remote
commander are pressed, the output power can be changed.
Press the [ENT] button on the remote commander, return to
item selection screen.
item selection screen.
7. Press the [V] and [v] buttons on the remote commander to
select the “CHK RFCH”, and press the [ENT] button on the
remote commander.
remote commander.
The RF CH used is displayed on the fl uorescent indicator tube.
Press the [ENT] button on the remote commander, return to
item selection screen.
item selection screen.
8. Press the [V] and [v] buttons on the remote commander to
select the “ENC KEY”, and press the [ENT] button on the re-
mote commander.
mote commander.
The message “ON” or “OFF” appears on the fl uorescent in-
dicator tube. In this state, whenever the [V] and [v] buttons
dicator tube. In this state, whenever the [V] and [v] buttons
on the remote commander are pressed, on/off can be changed
(When EVK is connected, this mode is used).
(When EVK is connected, this mode is used).
Press the [ENT] button on the remote commander, return to
item selection screen.
item selection screen.
9. Press the [V] and [v] buttons on the remote commander to
select the “VER.CHECK”, and press the [ENT] button on the
remote commander.
remote commander.
The microcomputer version last updated date of the S-AIR
device connected with this set is displayed on the fl uorescent
indicator tube.
device connected with this set is displayed on the fl uorescent
indicator tube.
Press the [ENT] button on the remote commander, return to
item selection screen.
item selection screen.
10. Press the [V] and [v] buttons on the remote commander to
select the “DARR”, and press the [ENT] button on the remote
commander.
commander.
The setting of DARR are displayed on the fl uorescent indi-
cator tube. Whenever the [V] and [v] buttons on the remote
cator tube. Whenever the [V] and [v] buttons on the remote
commander are pressed, the displayed setting of DARR can be
changed.
changed.
“CO XXXX” : Connect code display.
“NAMG XXX” : NAMG display.
“MUADR XXX”
: Address display.
“MUCO XXXX”
: MU code display.
“MUCNT XXX”
: Number of connected device.
Press the [ENT] button on the remote commander, return to
item selection screen.
item selection screen.
11. Press the [V] and [v] buttons on the remote commander to se-
lect the “CH1 PIPE”, and press the [ENT] button on the remote
commander.
commander.
The connection of DARR CH is displayed on the fl uorescent
indicator tube. Whenever the [V] and [v] buttons on the re-
indicator tube. Whenever the [V] and [v] buttons on the re-
mote commander are pressed, the connection of DARR CH
can be changed.
can be changed.
Press the [ENT] button on the remote commander, return to
item selection screen.
item selection screen.
12. Press the [V] and [v] buttons on the remote commander to se-
lect the “CH2 PIPE”, and press the [ENT] button on the remote
commander.
commander.
The connection of DARR CH is displayed on the fl uorescent
indicator tube. Whenever the [V] and [v] buttons on the re-
indicator tube. Whenever the [V] and [v] buttons on the re-
mote commander are pressed, the connection of DARR CH
can be changed.
can be changed.
Press the [ENT] button on the remote commander, return to
item selection screen.
item selection screen.
13. Press the [V] and [v] buttons on the remote commander to se-
lect the “CH3 PIPE”, and press the [ENT] button on the remote
commander.
commander.
The connection of DARR CH is displayed on the fl uorescent
indicator tube. Whenever the [V] and [v] buttons on the re-
indicator tube. Whenever the [V] and [v] buttons on the re-
mote commander are pressed, the connection of DARR CH
can be changed.
can be changed.
Press the [ENT] button on the remote commander, return to
item selection screen.
item selection screen.
14. Press the [V] and [v] buttons on the remote commander to se-
lect the “CH4 PIPE”, and press the [ENT] button on the remote
commander.
commander.
The connection of DARR CH is displayed on the fl uorescent
indicator tube. Whenever the [V] and [v] buttons on the re-
indicator tube. Whenever the [V] and [v] buttons on the re-
mote commander are pressed, the connection of DARR CH
can be changed.
can be changed.
Press the [ENT] button on the remote commander, return to
item selection screen.
item selection screen.
15. Press the [V] and [v] buttons on the remote commander to
select the “NAMG”, and press the [ENT] button on the remote
commander.
commander.
The setting value of NAMG is displayed on the fl uorescent in-
dicator tube. Whenever the [V] and [v] buttons on the remote
dicator tube. Whenever the [V] and [v] buttons on the remote
commander are pressed, the setting value of NAMG can be
changed.
changed.
Press the [ENT] button on the remote commander, return to
item selection screen.
item selection screen.
16. Press the [V] and [v] buttons on the remote commander to se-
lect the “ANT SET”, and press the [ENT] button on the remote
commander.
commander.
The setting of antenna transceiving is displayed on the fl uores-
cent indicator tube. Whenever the [V] and [v] buttons on the
cent indicator tube. Whenever the [V] and [v] buttons on the
remote commander are pressed, the setting of antenna trans-
ceiving can be changed.
ceiving can be changed.
Press the [ENT] button on the remote commander, return to
item selection screen.
item selection screen.
17. Press the [V] and [v] buttons on the remote commander to
select the “DEMO”, and press the [ENT] button on the remote
commander.
commander.
The message “ON” or “OFF” appears on the fl uorescent in-
dicator tube. Whenever the [V] and [v] buttons on the remote
dicator tube. Whenever the [V] and [v] buttons on the remote
commander are pressed, the on/off can be changed.
“ON” : Demo mode (Mode for demonstration at shops).
“OFF” : Normal mode.
Press the [ENT] button on the remote commander, return to
item selection screen.
item selection screen.
18. To release from this mode, press the [
?/1
] button. The setting
is maintained until turning off power.
2-18. S-AIR Radio Test Mode
Not used for the servicing.
Press the [
Not used for the servicing.
Press the [
?/1
] button if having entered this mode.
2-19. UART Flash Update
Not used for the servicing.
Press the [
Not used for the servicing.
Press the [
?/1
] button if having entered this mode.
2-20. Cold
Reset
Note: Execute this mode before returning the customer this set.
Procedure:
1. Enter the test menu.
2. Press the [V] and [v] buttons on the remote commander to
1. Enter the test menu.
2. Press the [V] and [v] buttons on the remote commander to
select the “COLD RESET”, and press the [ENT] button on the
remote commander.
remote commander.
3. The message “COLD RESET.” appears on the fl uorescent in-
dicator tube, then turn the power off.
Click on the first or last page to see other SA-WCT500 / SS-CT500 service manuals if exist.