Sony SA-WCT500 / SS-CT500 Service Manual ▷ View online
SA-WCT500/SS-CT500
6
SECTION 2
DISASSEMBLY
• This set can be disassembled in the order shown below.
• SA-WCT500 only is described in this section.
• SA-WCT500 only is described in this section.
2-1. DISASSEMBLY FLOW
Note: Follow the disassembly procedure in the numerical order given.
2-2. AMP BLOCK
2-2. AMP
BLOCK
(Page
6)
SET
2-3. FRONT PANEL BLOCK
(Page
(Page
7)
2-4. BRACKET
(TOP)
(Page
9)
2-5. S-AIR BOARD, TUNER (FM/AM)
(Page
(Page
9)
2-6. D-VIDEO
BOARD
(Page
10)
2-7. MAIN
BOARD
(Page
11)
2-8. POWER
BOARD
(Page
11)
1 five screws (BVTT4 u 20)
3 connector
(CN562)
5 wire (flat type)
(15 core) (CN1001)
4 cushion
(saranet-A)
2
6 AMP block
SA-WCT500/SS-CT500
7
2-3. FRONT PANEL BLOCK
Note: Work after laying the set sideways.
4
2 Insert the jig (J-2501-238-A) into a space
made by inserting the screwdriver,
and raise the front panel assy gradually.
2 Insert the jig (J-2501-238-A) into a space
made by inserting the screwdriver,
and raise the front panel block gradually.
3 Raise the front panel block a little by little
from bottom to top of the set.
eight bosses
bottom side
1 Insert a flat-head screwdriver into a recess
in the bottom of the set
to raise the front panel assy a little.
5 front panel block
SA-WCT500/SS-CT500
8
• NOTE WHEN FRONT PANEL BLOCK IS INSTALLED
2 Fix in the cushion (saranet-A) after
connecting the wire (flat type) (15 core).
1 Pass in bracket (holder) after pulling out the wire (flat type) (15 core)
from the hole where inside of front panel assy is seen.
bracket (holder)
– Rear side view –
3 Bend the wire (flat type) (15 core) and harness
from the loud speaker (13 cm) to the this side,
and insert the AMP block in the cabinet assy
with they put on AMP block.
4
hole
AMP block
wire (flat type)
(15 core)
(15 core)
inside of
front panel
front panel
cabinet assy
SA-WCT500/SS-CT500
9
2-4. BRACKET
(TOP)
2-5. S-AIR BOARD, TUNER (FM/AM)
2 eleven screws (BVTP3 u 8)
3 bracket (top)
1 screw (BVTP3 u 8)
2 screw (BVTP3 u 8)
(Except US, Canadian)
5 connector
(CN1303)
4 wire (flat type)
(19 core) (CN1301)
9 S-AIR board
1 two screws (BVTP3 u 8)
2 bracket (S-AIR)
3 fabric non woven (15T25)
6 two screws (BVTP3 u 8)
7 two screws (BVTP2.6)
8 holder (S-AIR)
0 fabric non woven (15T25)
qa wire (flat type) (9 core)
(US, Canadian, Saudi Arabia models),
wire (flat type) (11 core)
(AEP, Russian, UK models)
qd tuner (FM/AM)
qs two screws (BVTP3 u 8)
Click on the first or last page to see other SA-WCT500 / SS-CT500 service manuals if exist.