Sony SA-WCT380 / SA-WCT381 Service Manual ▷ View online
SA-WCT380/WCT381
5
ADVANCE PREPARATION WHEN CONFIRMING OP-
ERATION
All of the units included in the HT-CT380/CT381 (SA-WCT380/
WCT381, SA-CT380/CT381, Remote control) are required to con-
fi rming operation of SA-WCT380/WCT381. Check in advance
that you have all of the units.
ERATION
All of the units included in the HT-CT380/CT381 (SA-WCT380/
WCT381, SA-CT380/CT381, Remote control) are required to con-
fi rming operation of SA-WCT380/WCT381. Check in advance
that you have all of the units.
NOTE OF REPLACING THE SUB KEY BOARD
When the SUB KEY board is defective, replace the complete
mounted board.
When the SUB KEY board is defective, replace the complete
mounted board.
NOTE OF REPLACING THE IC7400 ON THE SUB MAIN
BOARD
IC7400 on the SUB MAIN board cannot replace with single. When
this part is damaged, replace the complete mounted board.
BOARD
IC7400 on the SUB MAIN board cannot replace with single. When
this part is damaged, replace the complete mounted board.
NOTE OF REPLACING THE IC7203 ON THE SUB MAIN
BOARD AND THE COMPLETE SUB MAIN BOARD
When IC7203 on the SUB MAIN board and the complete SUB
MAIN board are replaced, it is necessary to spread the compound
between the SUB MAIN board and the heat sink.
Spread the compound referring to the fi gure below.
BOARD AND THE COMPLETE SUB MAIN BOARD
When IC7203 on the SUB MAIN board and the complete SUB
MAIN board are replaced, it is necessary to spread the compound
between the SUB MAIN board and the heat sink.
Spread the compound referring to the fi gure below.
– SUB MAIN Board (Component Side) –
IC7203
compound
NOTES ON THE WIRELESS CONNECTION (LINK) AFTER
REPAIRS ARE COMPLETE
When the parts below is replaced, the wireless connection (LINK)
of the Bar speaker and Subwoofer will be disconnected.
Before returning repaired products to the customer, follow the pro-
cedure below to LINK the Bar speaker and Subwoofer.
Also, if only the Bar speaker or Subwoofer is brought in for repair
and the parts below are replaced, be sure to inform the customer
when returning the repaired products that the customer must LINK
the Bar speaker and Subwoofer.
(Indicate that the LINK procedure is described in the operating
instructions)
REPAIRS ARE COMPLETE
When the parts below is replaced, the wireless connection (LINK)
of the Bar speaker and Subwoofer will be disconnected.
Before returning repaired products to the customer, follow the pro-
cedure below to LINK the Bar speaker and Subwoofer.
Also, if only the Bar speaker or Subwoofer is brought in for repair
and the parts below are replaced, be sure to inform the customer
when returning the repaired products that the customer must LINK
the Bar speaker and Subwoofer.
(Indicate that the LINK procedure is described in the operating
instructions)
Parts in which the LINK will be disconnected due to re-
placement:
• Complete SUB MAIN board
• RF modulator (SWA12-4V RX) (Ref. No. RF1)
placement:
• Complete SUB MAIN board
• RF modulator (SWA12-4V RX) (Ref. No. RF1)
Linking the system (Link to the Subwoofer)
Set up the wireless subwoofer
connection again.
connection again.
1
Press MENU.
2
Select [WS] with j (select), then
press ENTER.
press ENTER.
3
Select [LINK] with j (select), then
press ENTER.
press ENTER.
4
When [START] appears on the
display, press ENTER.
[SEARCH] appears, and the Bar
Speaker searches for a device that
can be used with Link. Proceed to
the next step within 1 minute.
To quit the Link function while
searching for a device, press BACK.
display, press ENTER.
[SEARCH] appears, and the Bar
Speaker searches for a device that
can be used with Link. Proceed to
the next step within 1 minute.
To quit the Link function while
searching for a device, press BACK.
5
Press LINK on the subwoofer.
The on/standby indicator on the
subwoofer lights up in green. [OK]
appears on the display of the Bar
Speaker.
If [FAILED] appears, check to ensure
the subwoofer is turned on and
perform the process again from
step 1.
The on/standby indicator on the
subwoofer lights up in green. [OK]
appears on the display of the Bar
Speaker.
If [FAILED] appears, check to ensure
the subwoofer is turned on and
perform the process again from
step 1.
6
Press MENU.
The menu turns off.
The menu turns off.
THE ON/STANDBY INDICATOR FLASHES IN RED
– Press the Ò/Æ (on/standby)
button of the subwoofer to turn
off the power and check
whether the ventilation opening
of the subwoofer is blocked or
not.
off the power and check
whether the ventilation opening
of the subwoofer is blocked or
not.
Ç
SA-WCT380/WCT381
6
BOND FIXATION OF ELECTRIC PARTS
When the following parts are replaced, fi x the parts by using the bond (SC608Z2) (Refer to the fi gure below).
When the following parts are replaced, fi x the parts by using the bond (SC608Z2) (Refer to the fi gure below).
Target parts:
< SUB MAIN board >
C7233, C7234, L7202
< SUB POWER board >
C902 or C906, C903 or C908, C904 or C905, C907 or C988, C914 or C915, C935 or C938, C939, C967, C970, C976 to C978, C980, D901,
L966, LF901, R944, TH901, VDR901
< SUB MAIN board >
C7233, C7234, L7202
< SUB POWER board >
C902 or C906, C903 or C908, C904 or C905, C907 or C988, C914 or C915, C935 or C938, C939, C967, C970, C976 to C978, C980, D901,
L966, LF901, R944, TH901, VDR901
– SUB MAIN Board (Component Side) –
C7233
L7202
C7234
– SUB POWER Board (Component Side) –
C914/915
C902/906
C903/908
D901
C907/988
TH901
LF901
C904/905
VDR901
C935/938
C939
R944
C970
C967
C978
C980
– Side view –
C967
C977
C976
L966
SA-WCT380/WCT381
7
SECTION 2
DISASSEMBLY
• This set can be disassembled in the order shown below.
2-1. DISASSEMBLY FLOW
Note: Follow the disassembly procedure in the numerical order given.
2-2. SUB AMP BLOCK
SET
2-4. POWER CORD (AC1)
(Page
(Page
9)
2-5. SUB POWER BOARD
(Page
(Page
10)
2-6. RF MODULATOR (SWA12-4V RX) (RF1)
(Page
(Page
11)
2-7. SUB KEY BOARD, BUTTON (POWER-CZ2)
(Page
(Page
11)
2-2. SUB
AMP
BLOCK
(Page
7)
2-3. SUB MAIN BOARD
(Page
(Page
8)
2-9. LOUDSPEAKER (13 cm) (SP1)
(Page
(Page
13)
2-8. SUB LED BOARD, PANEL ASSY
(Page
(Page
12)
JIG
When disassembling the unit, use the following
jig for speaker removal.
jig for speaker removal.
Part No.
Description
J-2501-238-A JIG FOR SPEAKER REMOVAL
5 SUB LED board cable connector
(CN
7405
)
4 speaker cable connector
(CN
7202
)
3 Remove two cables from
the wiring stopper.
:LUHVHWWLQJ
SUB MAIN board
CN7405
CN7202
wiring stopper
2 Remove the sub MAIN block
in the direction of the arrow.
1 seven tapping screws
(3.5
u 16)
6 sub AMP block
1 seven tapping screws
(3.5
u 16)
–5HDUYLHZ–
Insert only part way.
Insert straight into
the interior.
the interior.
connector
Insert at a slant.
connector
connector
connector
connector
connector
OK
NG
NG
+RZWRLQVWDOOWKHFRQQHFWRU
Insert the connector straight into the interior.
There is a possibility that using this unit without
the connector correctly installed will damage it.
Insert the connector straight into the interior.
There is a possibility that using this unit without
the connector correctly installed will damage it.
SA-WCT380/WCT381
8
2-3. SUB MAIN BOARD
Note 1: When the complete SUB MAIN board is replaced, refer to
“NOTE OF REPLACING THE IC7203 ON THE SUB MAIN
BOARD AND THE COMPLETE SUB MAIN BOARD” and
“NOTES ON THE WIRELESS CONNECTION (LINK) AF-
TER REPAIRS ARE COMPLETE” on page 5.
BOARD AND THE COMPLETE SUB MAIN BOARD” and
“NOTES ON THE WIRELESS CONNECTION (LINK) AF-
TER REPAIRS ARE COMPLETE” on page 5.
+RZWRLQVWDOOWKHIOH[LEOHIODWFDEOH3
3 Remove the wire
from the wiring stopper.
IC7203
2 connector (CN7010)
1 flexible flat cable (24P)
(FFC1)
(CN7406)
7 two screws
(BVTP3
u 8)
5 two screws
(BVTP3
u 8)
9 SUB MAIN board
5 screw
(BVTP3
u 8)
6 wiring stopper
5 screw
(BVTP3
u 8)
8 heat sink
Note
3: When installing the heat sink, spread
the compound referring to “NOTE OF
REPLACING THE IC7203 ON THE
SUB
MAIN BOARD AND THE
COMPLETE SUB MAIN BOARD”
on servicing notes (page 5).
flexible flat cable (24P)
(FFC1)
(FFC1)
terminal face
CN7406
4 connector (CN7201)
Note
2: Before connect this connector,
refer to “CAPACITOR
ELECTRICAL
DISCHARGE
PROCESSING” on page 3.
Insert only part way.
Insert straight into
the interior.
the interior.
connector
Insert at a slant.
connector
connector
connector
connector
connector
OK
NG
NG
+RZWRLQVWDOOWKHFRQQHFWRU
Insert the connector straight into the interior.
There is a possibility that using this unit without
the connector correctly installed will damage it.
Insert the connector straight into the interior.
There is a possibility that using this unit without
the connector correctly installed will damage it.
colored line
Insert straight into the interior.
flexible flat
cable
cable
connector
OK
colored line
Insert at a slant.
flexible flat
cable
cable
connector
NG
+RZWRLQVWDOOWKHIOH[LEOHIODWFDEOH
When installing the flexible flat cable, ensure that
the colored line is parallel to the connector after insertion.
When installing the flexible flat cable, ensure that
the colored line is parallel to the connector after insertion.
Click on the first or last page to see other SA-WCT380 / SA-WCT381 service manuals if exist.