Sony SA-WCT260H Service Manual ▷ View online
SA-WCT260H
4
MODEL IDENTIFICATION
Distinguish by model number label stuck on the rear side of a main unit.
Distinguish by model number label stuck on the rear side of a main unit.
MODEL NUMBER LABEL
– Rear view –
US and Canadian models
AEP model
UK model
Australian model
4-463-510-0
s
4-463-513-0
s
4-463-511-0
s
4-463-512-0
s
SA-WCT260H
5
SECTION 2
DISASSEMBLY
•
This set can be disassembled in the order shown below.
2-1. DISASSEMBLY FLOW
SET
2-6. POWER
BOARD
(Page
7)
2-7. AMP
BOARD
(Page
8)
2-8. POWER-SUPPLY CORD (AC1)
(Page
(Page
9)
2-2. BACK
COVER
ASSY
(Page
5)
2-5. AMP
BLOCK
(Page
7)
2-9. BOTTOM COVER BLOCK
(Page
(Page
10)
2-3. LED
BOARD,
TOP
COVER
ASSY
(Page
6)
2-4. TOP
PLATE
(Page
6)
Note: Follow the disassembly procedure in the numerical order given.
2-2. BACK COVER ASSY
1 two screws
(BV3)
1 two screws
(BV3)
3 Pull out the power-supply cord.
2 Remove the back cover assy in
the direction of an arrow.
4 back cover assy
back cover assy
1 two screws
(BV3)
A
A
A
1 two screws
(BV3)
2 Remove the back cover assy in
the direction of an arrow.
– Rear view –
(US, Canadian, AEP)
(UK, Australian)
SA-WCT260H
6
2-4. TOP PLATE
1 six screws
(BV3)
1 four screws
(BV3)
boss
boss
hole
hole
2 Remove the top plate
in the direction of an arrow.
3 top plate
Note: When installing the top plate,
make the position of two holes
match two bosses.
– Rear view –
1 two screws
(BV3)
2-3. LED BOARD, TOP COVER ASSY
5 screw
(BVTP2.6)
5 screw
(BVTP2.6)
4 connector
(XP11)
2 Remove the top cover assy
in the direction of an arrow.
8 top cover assy
3 two claws
3 two claws
6 Remove the LED board
in the direction of an arrow.
7 LED board
– Rear view –
1 screw
(BV3)
1 screw
(BV3)
SA-WCT260H
7
2 two tapping screws
(P3.5
u 12)
2 tapping screw
(P3.5
u 12)
2 tapping screw
(P3.5
u 12)
1 speaker connector
(XP6)
4 AMP block
3 Remove the AMP block
in the direction of an arrow.
– Rear view –
1 power-supply cord connector
(CN
501
)
5 POWER board
4 Remove the POWER
board in the direction
of an arrow.
– Rear view –
– Top view –
power-supply cord
POWER board
:ire VeWWiQJ
2 connector
(XP12)
Insert is shallow
Insert is straight
to the interior.
to the interior.
connector
Insert is incline
connector
connector
connector
connector
connector
NG
OK
NG
Note: When you install the connector, please
install them correctly.
There is a possibility that this machine
damages when not correctly installing it.
3 two screws
(BV3)
3 two screws
(BV3)
2-5. AMP BLOCK
2-6. POWER BOARD