Sony SA-WCT260H Service Manual ▷ View online
SA-WCT260H
3
SECTION 1
SERVICING NOTES
ADVANCE PREPARATION WHEN CONFIRMING OP-
ERATION
All of the units included in the HT-CT260H (SA-WCT260H/SA-
CT260H) are required to confi rming operation of SA-WCT260H.
Check in advance that you have all of the units.
ERATION
All of the units included in the HT-CT260H (SA-WCT260H/SA-
CT260H) are required to confi rming operation of SA-WCT260H.
Check in advance that you have all of the units.
ABOUT PART REPAIR OF EACH BOARD
When mounted parts on each board installed by this unit are defec-
tive, replace the complete mounted board.
However the U701 on the AMP board is exchangeable. Refer to
“ELECTRICAL PARTS LIST” (page 24) for U701.
When mounted parts on each board installed by this unit are defec-
tive, replace the complete mounted board.
However the U701 on the AMP board is exchangeable. Refer to
“ELECTRICAL PARTS LIST” (page 24) for U701.
You can link the Sound Bar (SA-CT260H)
and the subwoofer (SA-WCT260H) again
to enable wireless transmission between
them.
and the subwoofer (SA-WCT260H) again
to enable wireless transmission between
them.
1
Press LINK on the rear of the
subwoofer with the point of a
pen, etc.
subwoofer with the point of a
pen, etc.
The subwoofer keeps beeping for
a certain time. Perform steps 2 to 5
before the subwoofer stops
beeping.
a certain time. Perform steps 2 to 5
before the subwoofer stops
beeping.
2
Press AMP MENU.
3
Select “WS” with
(select),
then press
.
4
Select “LINK,” then press
.
AMP
MENU
MENU
5
“START” appears, then press
.
“SEARCH” appears, and the Sound
Bar searches for equipment that
can be used with Link. Proceed to
the next step within 1 minute.
To quit the Link function during a
search for equipment, press
Bar searches for equipment that
can be used with Link. Proceed to
the next step within 1 minute.
To quit the Link function during a
search for equipment, press
.
When subwoofer is linked with the
Sound Bar, the
Sound Bar, the
indicator on
the subwoofer lights up in green
and the subwoofer beeps once.
“OK” appears on the front panel
display.
If “FAILED” appears or the
subwoofer does not stop beeping,
perform the process again from
step 1.
and the subwoofer beeps once.
“OK” appears on the front panel
display.
If “FAILED” appears or the
subwoofer does not stop beeping,
perform the process again from
step 1.
6
Press AMP MENU.
The AMP menu turns off.
NOTE OF REPLACING THE WS R BOARD
When the WS R board is exchanged, you must perform linking
between SA-CT260H and SA-WCT260H.
When the WS R board is exchanged, you must perform linking
between SA-CT260H and SA-WCT260H.
Linking method:
This operation requires a remote commander.
This operation requires a remote commander.
Ver. 1.1
SA-WCT260H
4
MODEL IDENTIFICATION
Distinguish by model number label stuck on the rear side of a main unit.
Distinguish by model number label stuck on the rear side of a main unit.
MODEL NUMBER LABEL
– Rear view –
US and Canadian models
AEP model
UK model
Australian model
4-463-510-0
s
4-463-513-0
s
4-463-511-0
s
4-463-512-0
s
SA-WCT260H
5
SECTION 2
DISASSEMBLY
•
This set can be disassembled in the order shown below.
2-1. DISASSEMBLY FLOW
SET
2-6. POWER
BOARD
(Page
7)
2-7. AMP
BOARD
(Page
8)
2-8. POWER-SUPPLY CORD (AC1)
(Page
(Page
9)
2-2. BACK
COVER
ASSY
(Page
5)
2-5. AMP
BLOCK
(Page
7)
2-9. BOTTOM COVER BLOCK
(Page
(Page
10)
2-3. LED
BOARD,
TOP
COVER
ASSY
(Page
6)
2-4. TOP
PLATE
(Page
6)
Note: Follow the disassembly procedure in the numerical order given.
2-2. BACK COVER ASSY
1 two screws
(BV3)
1 two screws
(BV3)
3 Pull out the power-supply cord.
2 Remove the back cover assy in
the direction of an arrow.
4 back cover assy
back cover assy
1 two screws
(BV3)
A
A
A
1 two screws
(BV3)
2 Remove the back cover assy in
the direction of an arrow.
– Rear view –
(US, Canadian, AEP)
(UK, Australian)
SA-WCT260H
6
2-4. TOP PLATE
1 six screws
(BV3)
1 four screws
(BV3)
boss
boss
hole
hole
2 Remove the top plate
in the direction of an arrow.
3 top plate
Note: When installing the top plate,
make the position of two holes
match two bosses.
– Rear view –
1 two screws
(BV3)
2-3. LED BOARD, TOP COVER ASSY
5 screw
(BVTP2.6)
5 screw
(BVTP2.6)
4 connector
(XP11)
2 Remove the top cover assy
in the direction of an arrow.
8 top cover assy
3 two claws
3 two claws
6 Remove the LED board
in the direction of an arrow.
7 LED board
– Rear view –
1 screw
(BV3)
1 screw
(BV3)