Sony SA-WCT260 Service Manual ▷ View online
SA-WCT260
4
MODEL IDENTIFICATION
Distinguish by model number label stuck on the rear side of a main unit.
Distinguish by model number label stuck on the rear side of a main unit.
MODEL NUMBER LABEL
US and Canadian models
AEP model
UK model
SA-WCT260 UC2
4-434-526-0s
SA-WCT260 CEL
4-434-528-0s
SA-WCT260 CEK
4-438-046-0s
Singapore model
SA-WCT260 SP1
4-438-047-0s
Russian model
SA-WCT260 RU3
4-438-049-0s
Australian model
SA-WCT260 AU1
4-447-896-0s
Brazilian model
SA-WCT260 BR1
4-447-897-0s
– Rear side view –
Ver. 1.1
SA-WCT260
5
SECTION 2
DISASSEMBLY
• This set can be disassembled in the order shown below.
2-1. DISASSEMBLY FLOW
SET
2-6. POWER CORD (AC1)
(Page
(Page
8)
2-7. SUB
AMP
BLOCK
(Page
9)
2-2. REAR
PANEL
(Page
5)
2-5. POWER
BOARD
(Page
7)
2-8. SUB MAIN BOARD
(Page
(Page
9)
2-10. LOUDSPEAKER (13 cm)
(SP100)
(Page
(SP100)
(Page
11)
2-9. BOTTOM PANEL BLOCK
(Page
(Page
10)
2-3. FRONT LED BOARD, TOP PANEL ASSY
(Page
(Page
6)
2-4. TOP PLATE BLOCK,
FUSE
FUSE
(F900)
(Page
7)
Note: Follow the disassembly procedure in the numerical order given.
2-2. REAR PANEL
1 two screws
(BVTP3
u 8)
1 two screws
(BVTP3
u 8)
3 Pull out the power code.
2 Remove the rear panel in
the direction of an arrow.
4 rear panel
– Rear side view –
SA-WCT260
6
2-3. FRONT LED BOARD, TOP PANEL ASSY
1 screw
(BVTP3
u 8)
1 screw
(BVTP3
u 8)
total four bosses
clamp (L35)
:LUHVHWWLQJ
sub AMP block
SW cabinet
Wire to FRONT LED board.
Wire from SUB MAIN board.
7 screw
(BVTP2.6)
6 LED cover
7 screw
(BVTP2.6)
5 connector
(CN901)
3 Remove the top panel block
in the direction of an arrow.
0 top panel assy
8 Remove the FRONT LED board
in the direction of an arrow.
9 FRONT LED board
4 Remove the wire from the clamp (L35).
–5HDUVLGHYLHZ–
3 All bosses are removed while
moving jig in the direction of
the arrow, and top panel assy
is
removed.
3 All bosses are removed while
moving jig in the direction of
the arrow, and top panel assy
is
removed.
2 Insert the jig into a space and raise
top panel assy.
Note 2: When using a jig, please work so
as not to injure top panel assy.
2 Insert the jig into a space and raise
top panel assy.
Note
2: When using a jig, please work so
as not to injure top panel assy.
• JIG
When disassembling the set, use the following jig (for speaker
When disassembling the set, use the following jig (for speaker
removal).
Part
No.
Description
J-2501-238-A
JIG FOR SPEAKER REMOVAL
SA-WCT260
7
2 power cord connector
(CN
900
)
power cord
5 clamp (L35)
clamp (L35)
4 screw
(BV3)
4 screw (BV3)
8 POWER board
POWER board
7 label fuse (T.H)
(EXCEPT US, Canadian)
3 connector
(CN
901
)
4 two screws
(BV3)
1 Remove the power cord
from the clamp (L35).
– Rear side view –
6 Remove the POWER
board in the direction
of an arrow.
PRwer FRrd seWWinJ
clamp (L35)
less than 5 mm
over 5 mm
OK
NG
single insulation wire
clamp (L35)
single insulation wire
2-4. TOP PLATE BLOCK, FUSE (F900)
1 seven screws
(BVTP3
u 8)
1 six screws
(BVTP3
u 8)
6 fuse (F900)
1 screw (BVTP3 u 8)
2 clamp (L35)
1 two screws
(BVTP3
u 8)
– Rear side view –
4 Pull out the wire.
boss
boss
hole
hole
3 Remove the top plate block
in the direction of an arrow.
5 top plate block
Note: When installing the top plate block,
make the position of two holes match
two
bosses.
2-5. POWER BOARD
Ver. 1.1
