Sony SA-TSS1 Service Manual ▷ View online
SA-TSS1
5
2-5. FRONT PANEL (L) ASSY (L-ch)
• JIG
When disassembling the unit, use the following jig (for speaker
When disassembling the unit, use the following jig (for speaker
removal).
Part
No.
Description
J-2501-238-A
JIG FOR SPEAKER REMOVAL
3 Remove the front panel (L) assy
in the direction of an arrow.
4 front panel (L) assy
– Bottom view –
total fourteen bosses
2 All bosses are removed while
moving jig in the direction of
the arrow, and front panel (L)
is
removed.
2 All bosses are removed while moving jig in the direction of
the arrow, and front panel (L) assy is removed.
1 Insert the jig into a space of bottom side
and raise front panel (L) assy.
Note: When using a jig, please work so
as not to injure grille assy and
cabinet.
1 Insert the jig into a space of bottom side
and raise front panel (L) assy.
Note: When using a jig, please work so as not
to injure grille assy and cabinet.
SA-TSS1
6
2-6. SPEAKER (8 cm) (SP1, SP2) (L-ch)
2-7. STAND (R) BLOCK (R-ch)
3
terminal (wide side)
[red]
3
terminal (narrow side)
[black]
1 two screws
(3.5
u 16)
1 two screws
(3.5
u 16)
2 Remove the speaker (8 cm)
(SP1) in the direction of an
arrow.
SP2
loudspeaker
(8 cm)
(8 cm)
top side
bottom side
speaker (8 cm)
[black]
(narrow side)
(narrow side)
[red]
(wide side)
(wide side)
:LUHVHWWLQJ
6SHDNHUFPVHWWLQJ
terminals position
–)URQWERWWRPYLHZ–
Note 2: When installing the speaker (8 cm),
make the position of terminals as
shown in the figure below.
4 speaker (8 cm) (SP1)
Note
1: Procedure of removal
of SP2 is the same as
the
SP1.
Note: Please spread a sheet under
a unit not to injure top panel.
2 stand (R) block
1 two tapping screws
(3.5
u 16)
– Rear bottom view –
1 two tapping screws
(3.5
u 16)
SA-TSS1
7
2-8. FRONT PANEL (R) ASSY (R-ch)
• JIG
When disassembling the unit, use the following jig (for speaker
When disassembling the unit, use the following jig (for speaker
removal).
Part
No.
Description
J-2501-238-A
JIG FOR SPEAKER REMOVAL
3 Remove the front panel (R) assy
in the direction of an arrow.
4 front panel (R) assy
– Bottom view –
total fourteen bosses
2 All bosses are removed while
moving jig in the direction of
the arrow, and front panel (R)
is
removed.
2 All bosses are removed while moving jig in the direction of
the arrow, and front panel (R) assy is removed.
1 Insert the jig into a space of bottom side
and raise front panel (R) assy.
Note: When using a jig, please work so
as not to injure grille assy and
cabinet.
1 Insert the jig into a space of bottom side
and raise front panel (R) assy.
Note: When using a jig, please work so as not
to injure grille assy and cabinet.
SA-TSS1
8
2-9. SPEAKER (8 cm) (SP3, SP4) (R-ch)
3
terminal (wide side)
[gray]
3
terminal (narrow side)
[black]
1 two screws
(3.5
u 16)
1 two screws
(3.5
u 16)
2 Remove the speaker (8 cm)
(SP3) in the direction of an
arrow.
SP4
loudspeaker
(8 cm)
(8 cm)
top side
bottom side
speaker (8 cm)
[black]
(narrow side)
(narrow side)
[gray]
(wide side)
(wide side)
:LUHVHWWLQJ
6SHDNHUFPVHWWLQJ
terminals position
–)URQWERWWRPYLHZ–
Note 2: When installing the speaker (8 cm),
make the position of terminals as
shown in the figure below.
4 speaker (8 cm) (SP3)
Note
1: Procedure of removal
of SP4 is the same as
the
SP3.
Click on the first or last page to see other SA-TSS1 service manuals if exist.