Sony SA-PSD5 / SA-WPSD5 / SS-SPSD5 Service Manual ▷ View online
Ver 1.1 2004.02
With SUPPLEMENT-1
With SUPPLEMENT-1
SERVICE MANUAL
5.1ch DIGITAL AUDIO SYSTEM
9-873-178-02
2004B16-1
© 2004.02
SPECIFICATIONS
SA-PSD5/WPSD5/
SS-SPSD5
• The SA-PSD5 system consists of one unit
of SA-WPSD5 and five units of SS-SPSD5.
General
Power requirements
Power requirements
120V AC, 60Hz (US, Canadian)
AC, 50/60 Hz (AEP, UK, E)
Power consumption
90 W (US, Canadian)
95 W (AEP, UK, E)
95 W (AEP, UK, E)
AUDIO POWER SPECIFICATIONS
POWER OUTPUT AND TOTAL HARMONIC DISTORTION:
POWER OUTPUT AND TOTAL HARMONIC DISTORTION:
With 3 ohm loads, both channels
driven, from 120 – 10,000 Hz; rated 25
watts per channel minimum RMS
power, with no more than 10 % total
harmonic distortion from 250
milliwatts to rated output.
driven, from 120 – 10,000 Hz; rated 25
watts per channel minimum RMS
power, with no more than 10 % total
harmonic distortion from 250
milliwatts to rated output.
SA-WPSD5 (subwoofer)
Max. output
Subwoofer:
Max. output
Subwoofer:
80 W (4 ohms)
Front:
40 W + 40 W (6 ohms)
Center*:
40 W
Rear*:
40 W + 40 W
* Depending on the sound field settings and the source, there may be
no sound output.
Speaker system Bass reflex
Speaker unit
Speaker unit
200 mm (7
7
/
8
inches) dia. cone type
Rated impedance
4 ohms
Dimensions (approx.)
300
× 300 × 300 mm
(11
7
/
8
× 11
7
/
8
× 11
7
/
8
inches) (w/h/d,
not including the projecting parts)
Mass (approx.) 9.7 kg (21 lb 6 oz )
SS-SPSD5 (satellite speakers)
Speaker system Bass reflex
Speaker unit
Speaker system Bass reflex
Speaker unit
77 mm (3
1
/
8
inches ) dia. cone type
Rated impedance
6 ohms
Dimensions (approx.)
110
× 115 × 110 mm
(4
3
/
8
× 4
5
/
8
× 4
3
/
8
inches) (w/h/d)
Mass (approx.) 780 g (1 lb 12 oz)
220 – 240 V
3.5 W (standby mode)
Operating temperature
5˚C to 35˚C (41˚F to 95˚F)
Operating humidity
5 % to 90 %
Supplied accessories
Design and specifications are subject to change without
notice.
notice.
• Subwoofer (1)
• Satellite speakers (5)
• Speaker cords (5 m (17 ft) x 3, 15 m (50 ft) x 2)
• Optical digital cord (1)
• Remote commander (remote) RM-UP51 (1)
• R6 (size AA) batteries (2)
• Foot pads (20)
• Satellite speakers (5)
• Speaker cords (5 m (17 ft) x 3, 15 m (50 ft) x 2)
• Optical digital cord (1)
• Remote commander (remote) RM-UP51 (1)
• R6 (size AA) batteries (2)
• Foot pads (20)
This system incorporates Dolby
*
Digital and Pro Logic
Surround and the DTS** Digital Surround System.
*
Manufactured under license from Dolby Laboratories.
“Dolby,” “Pro Logic,” and the double-D symbol are trademarks of
Dolby Laboratories.
“Dolby,” “Pro Logic,” and the double-D symbol are trademarks of
Dolby Laboratories.
**
Manufactured under license from Digital Theater Systems, Inc. US
Pat. No. 5,451,942 and other worldwide patents issued and pending.
“DTS” and “DTS Digital Surround” are trademarks of Digital
Theater Systems, Inc. © 1996 Digital Theater Systems, Inc. All
rights reserved.
Pat. No. 5,451,942 and other worldwide patents issued and pending.
“DTS” and “DTS Digital Surround” are trademarks of Digital
Theater Systems, Inc. © 1996 Digital Theater Systems, Inc. All
rights reserved.
US Model
Canadian Model
AEP Model
UK Model
E Model
Photo: SA-WPSD5
Photo: SS-SPSD5
Sony Corporation
Home Audio Company
Published by Sony Engineering Corporation
2
TABLE OF CONTENTS
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK
0
OR DOTTED LINE WITH
MARK
0
ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS
LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE
COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS
APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS
PUBLISHED BY SONY.
COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS
APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS
PUBLISHED BY SONY.
ATTENTION AU COMPOSANT AYANT RAPPORT
À LA SÉCURITÉ!
LES COMPOSANTS IDENTIFÉS PAR UNE MARQUE
0
SUR LES
DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT
CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE
REMPLACER CES COMPOSANTS QUE PAR DES PIÈSES SONY
DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU
DANS LES SUPPÉMENTS PUBLIÉS PAR SONY.
CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE
REMPLACER CES COMPOSANTS QUE PAR DES PIÈSES SONY
DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU
DANS LES SUPPÉMENTS PUBLIÉS PAR SONY.
SA-PSD5/WPSD5/SS-SPSD5
Notes on chip component replacement
• Never reuse a disconnected chip component.
• Notice that the minus side of a tantalum capacitor may be
• Notice that the minus side of a tantalum capacitor may be
damaged by heat.
Flexible Circuit Board Repairing
• Keep the temperature of soldering iron around 270˚C
during repairing.
• Do not touch the soldering iron on the same conductor of the
circuit board (within 3 times).
• Be careful not to apply force on the conductor when soldering
or unsoldering.
After correcting the original service problem, perform the
following safety checks before releasing the set to the customer:
Check the antenna terminals, metal trim, “metallized” knobs, screws,
and all other exposed metal parts for AC leakage. Check leakage as
described below.
following safety checks before releasing the set to the customer:
Check the antenna terminals, metal trim, “metallized” knobs, screws,
and all other exposed metal parts for AC leakage. Check leakage as
described below.
LEAKAGE
The AC leakage from any exposed metal part to earth ground
and from all exposed metal parts to any exposed metal part having
a return to chassis, must not exceed 0.5 mA (500 microamperes).
Leakage current can be measured by any one of three methods.
and from all exposed metal parts to any exposed metal part having
a return to chassis, must not exceed 0.5 mA (500 microamperes).
Leakage current can be measured by any one of three methods.
1.
A commercial leakage tester, such as the Simpson 229 or RCA
WT-540A. Follow the manufacturers’ instructions to use these
instruments.
WT-540A. Follow the manufacturers’ instructions to use these
instruments.
2.
A battery-operated AC milliammeter. The Data Precision 245
digital multimeter is suitable for this job.
digital multimeter is suitable for this job.
3.
Measuring the voltage drop across a resistor by means of a
VOM or battery-operated AC voltmeter. The “limit” indication
is 0.75 V, so analog meters must have an accurate low-voltage
scale. The Simpson 250 and Sanwa SH-63Trd are examples of
a passive VOM that is suitable. Nearly all battery operated
digital multimeters that have a 2V AC range are suitable. (See
Fig. A)
VOM or battery-operated AC voltmeter. The “limit” indication
is 0.75 V, so analog meters must have an accurate low-voltage
scale. The Simpson 250 and Sanwa SH-63Trd are examples of
a passive VOM that is suitable. Nearly all battery operated
digital multimeters that have a 2V AC range are suitable. (See
Fig. A)
SAFETY CHECK-OUT
To Exposed Metal
Parts on Set
0.15
µ
F
1.5 k
Ω
AC
Voltmeter
(0.75 V)
Voltmeter
(0.75 V)
Earth Ground
Fig. A. Using an AC voltmeter to check AC leakage.
SAFETY CHECK-OUT
················································· 2
1.
GENERAL
········································································· 3
2.
DIAGRAMS
······································································· 4
2-1. Circuit Boards Location ························································ 4
2-2. Block Diagrams ···································································· 5
2-3. Printed Wiring Board
2-2. Block Diagrams ···································································· 5
2-3. Printed Wiring Board
– Digital Section (Side A) – ·················································· 6
2-4. Printed Wiring Board
– Digital Section (Side B) – ················································· 7
2-5. Schematic Diagram – Digital Section (1/2) – ······················· 8
2-6. Schematic Diagram – Digital Section (2/2) – ······················· 9
2-7. Schematic Diagram – LCD Section – ··································· 10
2-8. Printed Wiring Board – LCD Section – ································ 11
2-9. Schematic Diagram – Key Section – ···································· 12
2-10. Printed Wiring Board – Key Section – ·································· 13
2-11. Schematic Diagram – IN/OUT Section – ····························· 14
2-12. Printed Wiring Board – IN/OUT Section – ··························· 15
2-13. Schematic Diagram – Pre Amp Section – ····························· 16
2-14. Printed Wiring Board – Pre Amp Section – ·························· 17
2-15. Schematic Diagram – Power Section (1/2) – ························ 18
2-16. Schematic Diagram – Power Section (2/2) – ························ 19
2-17. Printed Wiring Board – Power Section – ······························ 20
2-18. IC Block Diagrams ······························································· 21
2-19. IC Pin Function Description ················································· 23
2-6. Schematic Diagram – Digital Section (2/2) – ······················· 9
2-7. Schematic Diagram – LCD Section – ··································· 10
2-8. Printed Wiring Board – LCD Section – ································ 11
2-9. Schematic Diagram – Key Section – ···································· 12
2-10. Printed Wiring Board – Key Section – ·································· 13
2-11. Schematic Diagram – IN/OUT Section – ····························· 14
2-12. Printed Wiring Board – IN/OUT Section – ··························· 15
2-13. Schematic Diagram – Pre Amp Section – ····························· 16
2-14. Printed Wiring Board – Pre Amp Section – ·························· 17
2-15. Schematic Diagram – Power Section (1/2) – ························ 18
2-16. Schematic Diagram – Power Section (2/2) – ························ 19
2-17. Printed Wiring Board – Power Section – ······························ 20
2-18. IC Block Diagrams ······························································· 21
2-19. IC Pin Function Description ················································· 23
3.
EXPRODED VIEWS
······················································· 25
3-1. SA-WPSD5 (FRONT SECTION) ········································· 25
3-2. SA-WPSD5 (AMP SECTION) ············································· 26
3-3. SS-SPSD5 ············································································· 27
3-2. SA-WPSD5 (AMP SECTION) ············································· 26
3-3. SS-SPSD5 ············································································· 27
4.
ELECTRICAL PARTS LIST
········································ 28
3
SA-PSD5/WPSD5/SS-SPSD5
SECTION 1
GENERAL
18
GB
Index to Parts and Controls
Top panel/Front panel
1
SOUND FIELD button (11)
Selects the sound field.
Selects the sound field.
2
FUNCTION button (9)
Selects the input signal.
Selects the input signal.
3
?
/1 (POWER) switch and indicator (9)
Turns on and off the power of the system.
4
Display window (7, 9, 11, 14)
Indicates the speaker setting, input signal, sound field
mode, etc.
Indicates the speaker setting, input signal, sound field
mode, etc.
5
MASTER VOL (volume) +/– buttons (9)
Adjust the volume.
Adjust the volume.
6
MUTING button (9)
Mutes the sound.
Mutes the sound.
7
remote sensor (4)
Accepts the remote control signals.
Accepts the remote control signals.
Rear panel
8
SPEAKER jacks (5)
Connect to the supplied satellite speakers.
Connect to the supplied satellite speakers.
9
AUDIO IN 1/2 jacks (6)
Connect to the audio output of a TV, VCR, PSone, etc.
Connect to the audio output of a TV, VCR, PSone, etc.
0
DIGITAL IN OPTICAL 1/2 jacks (5, 6)
Connect to the DIGITAL OUT (OPTICAL) jack of the
“PlayStation 2,” DVD player, etc.
Connect to the DIGITAL OUT (OPTICAL) jack of the
“PlayStation 2,” DVD player, etc.
qa
BASS CONTROL knobs (10)
Make fine adjustment of the bass sound.
Make fine adjustment of the bass sound.
Refer to the pages indicated in parentheses for details.
Subwoofer
1
2
3
4
5
6
7
8
9
q;
qa
ONLY FOR
SS-SPSD5
SS-SPSD5
FRONT R
CENTER
SPEAKER
FRONT L
REAR R
REAR L
2
OPTICAL
2
MID
LOW
HIGH
MIN
MAX
LEVEL
FREQUENCY
1
1
L
R
BASS CONTROL
AUDIO IN
DIGITAL IN
19
GB
Remote
1
TV button (15)
Turns the TV on and off.
Turns the TV on and off.
2
SHIFT button (7, 10, 14, 15)
Switches the function of the buttons on the remote.
Switches the function of the buttons on the remote.
3
TV CH +/– (TV/VIDEO) buttons (15)
Changes the TV channel.
To change the TV input, press – while pressing SHIFT.
Changes the TV channel.
To change the TV input, press – while pressing SHIFT.
4
REAR +/– buttons (10)
Adjust the rear speakers volume.
Adjust the rear speakers volume.
5
CENTER +/– buttons (10)
Adjust the center speaker volume.
Adjust the center speaker volume.
6
X
PAUSE button (13)
Pauses playing a disc.
7
N
PLAY button (13)
Plays a disc.
8
.
/>PREV/NEXT buttons (13)
Press to go to the next chapter or track, or to go back
to the previous chapter or track.
to the previous chapter or track.
9
TITLE button (13)
Displays the title menu on the TV screen.
Displays the title menu on the TV screen.
0 <
/M/m/,/ENTER button
Selects and executes the items or settings.
qa
DISPLAY button (14)
Displays the setup display of the “PlayStation 2” or
DVD player.
Displays the setup display of the “PlayStation 2” or
DVD player.
qs
DVD 1/DVD 2 button (13)
Turns on and off the power of the DVD player.
Turns on and off the power of the DVD player.
qd
?
/1 (POWER) switch (7, 9)
Turns on and off the system.
qf
FUNCTION button (9)
Selects the input signal.
Selects the input signal.
qg
SOUND FIELD (SPEAKER SETUP) button (7, 11, 14)
Selects the sound field mode.
Pressing this button while pressing SHIFT will select
the speaker setup parameters.
Selects the sound field mode.
Pressing this button while pressing SHIFT will select
the speaker setup parameters.
qh
WOOFER +/– buttons (10)
Adjust the subwoofer volume.
Adjust the subwoofer volume.
qj
VOLUME +/– buttons (7, 9, 14)
Make the speaker settings or adjust the volume of the
system.
Pressing this button while pressing SHIFT will set the
speaker setup parameters.
Make the speaker settings or adjust the volume of the
system.
Pressing this button while pressing SHIFT will set the
speaker setup parameters.
qk
x
STOP button (13)
Stops playing a disc.
ql
MUTING (TEST TONE) button (9, 10)
Mutes the sound.
Pressing this button while pressing SHIFT will sound
the test tone.
Mutes the sound.
Pressing this button while pressing SHIFT will sound
the test tone.
w;
m
/M (SCAN) buttons (13)
Locate a point while monitoring the picture.
wa
DVD MENU button (13)
Displays the DVD menu on the TV screen.
Displays the DVD menu on the TV screen.
ws
RETURN button (14)
Returns to the previously selected screen.
Returns to the previously selected screen.
1
2
3
4
5
6
7
8
9
q;
qa
qs
qd
qf
qg
qh
qj
qk
ql
w;
wa
ws
SHIFT
TV CH
CENTER
FUNCTION
PLAY PAUSE
PREV
NEXT
SCAN
STOP MUTING
LEVEL
TV/VIDEO
SPEAKER SET UP
FIELD
SOUND
TV
DVD1
DVD2
REAR
WOOFER
TEST TONE
ENTER
DVD CONTROL
DVD MENU
TITLE
RETURN
DISPLAY
VOLUME
This section is e
xtr
acted
acted
from instr
uction man
ual.
4
SA-PSD5/WPSD5/SS-SPSD5
SECTION 2
DIAGRAMS
THIS NOTE IS COMMON FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS.
(In addition to this, the necessary note is printed in each block.)
(In addition to this, the necessary note is printed in each block.)
2-1. Circuit Boards Location
KEY-L board
POWER board
ADJ board
INPUT board
KEY-R board
PRE AMP board
DIGITAL board
SP board
SIRCS board
LCD board
Note on Schematic Diagram:
• All capacitors are in
• All capacitors are in
µ
F unless otherwise noted. p: pF.
50 WV or less are not indicated except for electrolytics
and tantalums.
and tantalums.
• All resistors are in
Ω
and
1
/
4
W or less unless otherwise
specified.
•
f
: internal component.
•
C
: panel designation.
Note on Printed Wiring Board:
• X
: parts extracted from the component side.
• Y
: parts extracted from the conductor side.
•
x
: parts mounted on the conductor side.
•
a
: Through hole.
•
: Pattern from the side which enables seeing.
(The other layers' patterns are not indicated.)
• Indication of transistor
Caution:
Pattern face side:
Pattern face side:
Parts on the pattern face side seen from
(SIDE A)
the pattern face are indicated.
Parts face side:
Parts on the parts face side seen from
(SIDE B)
the parts face are indicated.
Note:
The components identi-
fied by mark
The components identi-
fied by mark
0
or dotted
line with mark
0
are criti-
cal for safety.
Replace only with part
number specified.
Replace only with part
number specified.
Note:
Les composants identifiés par
une marque
Les composants identifiés par
une marque
0
sont critiques
pour la sécurité.
Ne les remplacer que par une
piéce por tant le numéro
spécifié.
Ne les remplacer que par une
piéce por tant le numéro
spécifié.
Q
C
These are omitted
E
B
•
A
: B+ Line.
•
B
: B– Line.
• Voltages and waveforms are dc with respect to ground
under no-signal (detuned) conditions.
• Voltages are taken with a VOM (Input impedance 10 M
Ω
).
Voltage variations may be noted due to normal produc-
tion tolerances.
tion tolerances.
• Waveforms are taken with a oscilloscope.
Voltage variations may be noted due to normal produc-
tion tolerances.
tion tolerances.
• Circled numbers refer to waveforms.
• Signal path.
F
: AUDIO (ANALOG)
J
: AUDIO (DIGITAL)
• Abbreviation
CND : Canadian model.
SP
SP
: Singapore model.
C
These are omitted
E
B
1
IC815
wz
XOUT
6.5
Vp-p
Vp-p
2
IC815
w;
XMCK
81.4 ns
3
IC815
qg
LRCK
6
IC701
qd
XOUT
4
IC815
qf
BCK
5
IC815
qd
CKOUT
6.1
Vp-p
Vp-p
5.6
Vp-p
Vp-p
5.0
Vp-p
Vp-p
5.6
Vp-p
Vp-p
4.7
Vp-p
Vp-p
81.4 ns
325 ns
81.4 ns
20.8
µ
s
62.5 ns
• WAVEFORMS
