Sony SA-NS310 Service Manual ▷ View online
SA-NS310
5
SECTION 2
DISASSEMBLY
•
This set can be disassembled in the order shown below.
2-1. DISASSEMBLY FLOW
SET
2-2. BOTTOM PANEL BLOCK
(Page
(Page
6)
2-3. MAIN BOARD BLOCK
(Page
(Page
7)
2-4. WIRELESS
LAN
MODULE
(12SA-NS310)
(MOD1),
MAIN BOARD
(Page
8)
2-6. ANT BOARD,
LEAD WIRE WITH CONNECTOR (LW1)
(Page
9)
2-5. BRACKET (ANTENNA) BLOCK
(Page
(Page
8)
2-7. PANEL BLOCK
(Page
(Page
10)
2-8. LOUDSPEAKER (5 cm) (SP1)
(Page
(Page
10)
SA-NS310
6
Note: Follow the disassembly procedure in the numerical order given.
2-2. BOTTOM PANEL BLOCK
1 four screws
(BVTP3
(BVTP3
u 12)
2 Remove the bottom panel block
in the direction of an arrow.
3 bottom panel block
– Rear bottom view –
Jacks has fitted in correctly.
The bottom panel has run
aground to the jack.
aground to the jack.
Note 2: When installing the bottom
panel block, check that each
jack has fitted in certainly.
OK
NG
knob (standby)
switch (S105)
MAIN board
Slide to “STANDBY” side.
Note 1: When installing the bottom panel block,
match the position of the knobs (standby)
and the switch (S105).
SA-NS310
7
2-3. MAIN BOARD BLOCK
4
shield (down) cushion (B)
shield (down) cushion (B)
5
lead wire with connector
lead wire with connector
1 speaker connector
(CN107)
(CN107)
IC111
MAIN board
hole of button (party)
boss
boss
2 Remove the MAIN board block
in the direction of an arrow.
6 MAIN board block
3 Remove the MAIN board block
in the direction of an arrow.
– Front bottom view –
Note 1: When installing the MAIN board block,
check that IC111 has not bent.
Note 2: Check that IC111 is correctly contained
in a hole.
Note 3: When installing the MAIN board block,
match the position of two bosses.
Note 4: Make width of both sides
the
the
same.
Note 6: When you install the connector, please install them correctly.
There is a possibility that this machine damages when not
correctly installing it.
speaker wire
:ire VettinJ
6KieOG Gown FXVKion % VettinJ
– %ottom view –
front side
Insert is shallow
Insert is straight
to the interior.
to the interior.
connector
Insert is incline
connector
connector
connector
connector
connector
NG
OK
NG
MAIN board
wireless LAN module
(12SA-NS310) (MOD1)
(12SA-NS310) (MOD1)
Note 5: There are two terminals for lead wire
with connector in a module.
When connecting the lead wire with
connector, connect with the right
terminal.
OK
NG
Note 7: Check the thing to which the wire is not slanting,
which have not floated and from which it has not
disconnected.
connector
connector
lead wire with connector
lead wire with connector
OK
NG
SA-NS310
8
2-5. BRACKET (ANTENNA) BLOCK
2-4. WIRELESS LAN MODULE (12SA-NS310) (MOD1), MAIN BOARD
Note: When replacing the wireless LAN module (12SA-NS310)
(Ref. No. MOD1), refer to “NOTE OF REPLACING
THE WIRELESS LAN MODULE (12SA-NS310)” and
“PROCESSING OF REPLACING THE WIRELESS
LAN MODULE (12SA-NS310)” (page 3).
THE WIRELESS LAN MODULE (12SA-NS310)” and
“PROCESSING OF REPLACING THE WIRELESS
LAN MODULE (12SA-NS310)” (page 3).
1 two screws
(BVTP2.6
(BVTP2.6
u 8)
4 two screws
(BVTP3
(BVTP3
u 10)
1 screw
(BVTP2.6
(BVTP2.6
u 8)
1 screw
(BVTP2.6
(BVTP2.6
u 8)
3 shield (up) block
2 shield (down) block
6 wireless LAN module (12SA-NS310)
(MOD1)
(MOD1)
7 BCO cushion
8 cushion (LED) (black)
8 cushion (LED)
(black)
(black)
9 cushion (LED) (blue)
9 cushion (LED) (blue)
0 cushion (link-LED)
qa MAIN board
5 connector
(CN102)
(CN102)
3 four tapping screws
(3.5
(3.5
u 14)
1 floating screw
(PTPWH M2.6)
(PTPWH M2.6)
2 ferrite core block
4 bracket (antenna) block
– Front bottom view –
:ire VettinJ
– Bottom view –
front side
ferrite core block
lead wire with connector
Click on the first or last page to see other SA-NS310 service manuals if exist.