Sony SA-CRW33 / SA-W33 / SS-CN33 / SS-F33H / SS-SR33 Service Manual ▷ View online
SA-CRW33/P33H/W33/SS-CN33/F33H/SR33
5
1-3. REAR COVER BLOCK (SA-W33)
Note:
This illustration sees the set from rear side.
1-4. CONTROL BOARD (SA-W33)
6 connector
(CNP902)
7 power cord connector
(CNP901)
4 connector
(CNP602)
1 twelve screws
(3.5
u 20)
2 two screws
(BVTP3
u 8)
8 rear cover block
5 connector
(CNP907)
3
2 two nuts
(supplied with RV101, RV102)
7 rear cover
1 two knobs (VOL)
8 cushion
qa CONTROL board
4 two screws (3.5)
9 knob power
3 screw (BVTP3 u 8)
Note: Tape etc. are wrapped and it pulls it
in the direction of the arrow at a dash.
– rear side –
0 fuse (TA1L/250V) (F901)
tape etc.
knob (VOL)
6 two washers
(supplied with RV101, RV102)
5
SA-CRW33/P33H/W33/SS-CN33/F33H/SR33
6
1-5. GRILLE FRAME ASSY (SS-CN33)
Note 1:
Please set as shown in fi gure and work.
1-6. GRILLE FRAME ASSY (SS-SR33)
Note 1:
Please set as shown in fi gure and work.
total seven bosses
2 Insert the jig (Part No. J-2501-238-A) into a space
and raise the grille frame assy gradually.
bottom side
1 Insert a flat-head screwdriver into
a recess in the bottom of the set
to raise the grille frame assy a little.
Note 2: When using a jig, please work so as not
to injure grille frame assy and speaker
cabinet
assy.
2 Insert the jig (Part No. J-2501-238-A)
into a space and raise the grille frame
assy
gradually.
Note 2: When using a jig, please work so
as not to injure grille frame assy
and speaker cabinet assy.
2 Insert the jig (Part No. J-2501-238-A)
into a space and raise the grille frame
assy
gradually.
Note 2: When using a jig, please work so
as not to injure grille frame assy
and speaker cabinet assy.
3 All bosses are removed while
moving jig in the direction of
the arrow, and grille frame assy
is
removed.
3 All bosses are removed while
moving jig in the direction of
the arrow, and grille frame assy
is
removed.
grille frame assy
total four bosses
2 Insert the jig (Part No. J-2501-238-A) into a space
and raise the grille frame assy gradually.
bottom side
1 Insert a flat-head screwdriver into
a recess in the bottom of the set
to raise the grille frame assy a little.
Note 2: When using a jig, please work so as not
to injure grille frame assy and speaker
cabinet
assy.
2 Insert the jig (Part No. J-2501-238-A) into a space
and raise the grille frame assy gradually.
Note 2: When using a jig, please work so as not
to injure grille frame assy and speaker
cabinet
assy.
3 All bosses are removed while
moving jig in the direction of
the arrow, and grille frame assy
is
removed.
3 All bosses are removed while
moving jig in the direction of
the arrow, and grille frame assy
is
removed.
grille frame assy
SA-CRW33/P33H/W33/SS-CN33/F33H/SR33
7
1-7. LOUDSPEAKER (10 cm) (SS-F33H)
1 two bosses
four bosses
This woofer ring can be removed as mutch on.
This loudspeaker (10 cm) (SP5)
can be removed as mutch on.
can be removed as mutch on.
1 two bosses
5 four screws
(3.5
u 16)
4 woofer ring
7 loudspeaker (10 cm) (SP4)
6 two terminals
Note: Please exchange woofer ring
at the same time when you
exchange
loudspeaker.
2 grille frame assy
3 Insert a flat-head screwdriver into a recess
in the direction of the woofer ring
to raise the speaker cabinet assy a little.
(The boss four places are removed to woofer
ring 1 piece)
woofer ring
SA-CRW33/P33H/W33/SS-CN33/F33H/SR33
8
MEMO
Click on the first or last page to see other SA-CRW33 / SA-W33 / SS-CN33 / SS-F33H / SS-SR33 service manuals if exist.