Sony PMC-DR45 Service Manual ▷ View online
– 13 –
4
BTP 2.8x8
5
BTP 2.8x8
3
panel assy, top
6
TOP board
1
BVTP 3x10
2
BVTP 3x10
3-12. TOP BOARD
1
P 2.6x8
2
plate assy, chuck
4
claw
5
claw
7
tray
6
3
3-13. “PLATE ASSY, CHUCK”, TRAY
– 14 –
5
B 2x3
6
claw
7
claw
8
LOADING board
1
belt
2
claw
3
pulley
4
CN651
2
P 2x5
3
CNP701
4
CD board
1
Removal the
four solders.
3-14. LOADING BOARD
3-15. CD BOARD
– 15 –
qa
CD mechanism block
CD mechanism block
0
arm
1
PWH 2.6x10
4
PWH 2.6x10
8
PWH 2.6x10
5
7
6
9
2
gear, drive
3
gear
arm
chassis
chassis
1
scews +B tapping
2
scews +B tapping
3
cabinet (rear), speaker
4
bracket, cover
qa
BVTP 3x10
qs
BVTP 3x10
qd
B 4x6
9
BTP 2.6x8
0
speaker board
qf
power board
5
CNP903
6
CNP911
7
CNP901
8
CNP902
3-16. CD MECHANISM BLOCK
3-17. POWER BOARD
– 16 –
Tape Speed Adjustment
Procedure:
Mode: playback
Mode: playback
32
Ω
test tape
WS-48B
(3 kHz, 0 dB)
WS-48B
(3 kHz, 0 dB)
set
i
(headphones) jack (J301)
digital frequency
counter
counter
Mode
Tension Meter
Meter Reading
FWD
CQ-403A
more than 100 g
REV
CQ-403R
(more than 3.52 oz)
Mode
Torque Meter
Meter Reading
3.53 – 5.98 mN•m
FWD
(36 – 61 g•cm)
CQ-102C
(0.50 – 0.89 oz•inch)
FWD
0.20 – 0.58 mN•m
Back tension
(2.0 – 6.0 g•cm)
(0.028 – 0.076 oz•inch)
3.53 – 5.98 mN•m
REV
(36 – 61 g•cm)
CQ-102RC
(0.50 – 0.89 oz•inch)
REV
0.20 – 0.58 mN•m
Back tension
(2.0 – 6.0 g•cm)
(0.028 – 0.076 oz•inch)
5.99 – 14.02 mN•m
FF, REW
CQ-201B
(61 – 143 g•cm)
(0.89 – 2.00 oz•inch)
Adjust so that the frequency at the beginning and that at the end of
tape winding are between 2,955 and 3,045 Hz.
tape winding are between 2,955 and 3,045 Hz.
Adjustment Location:
SECTION 5
ELECTRICAL ADJUSTMENTS
SECTION 4
MECHANICAL ADJUSTMENTS
PRECAUTION
1. Clean the following parts with a denatured-alcohol-moistened
swab:
record/playback/erase head
pinch roller
rubber belts
capstan
idlers
2. Demagnetize the record/playback/erase head with a head de-
magnetizer. (Do not bring the head demagnetizer close to the
erase head portion.)
erase head portion.)
3. Do not use a magnetized screwdriver for the adjustments.
4. After the adjustments, apply suitable locking compound to the
4. After the adjustments, apply suitable locking compound to the
parts adjusted.
5. The adjustments should be performed with the rated power sup-
ply voltage unless otherwise noted.
Torque Measurement
Tape Tension Measurement
Standard Output Level
Test Tape
5-1. TAPE SECTION 0 dB = 0.775 V
1. The adjustments should be performed in the order given in the
service manual. (As a general rule. Playback circuit adjustment
should be completed before performing recording circuit ad-
justment.)
should be completed before performing recording circuit ad-
justment.)
2. The adjustments should be performed for both L-ch and R-ch
unless otherwise indicated.
SP OUT
PHONES
Load impedance
4
Ω
32
Ω
Output level
0.775 V (0 dB)
0.25 V (–10 dB)
Type
Signal
Used for
WS-48B
3 kHz, 0 dB
Tape speed adjustment
P-4-A100
10 kHz, –10 dB
Head azimuth adjustment
Digital frequency counter
2,970 to 3,030 Hz
Adjust so that the value on the frequency counter is 3,000 Hz.
Specification Values:
TC board
M691
TAPE SPEED
Adjustment
Adjustment
Click on the first or last page to see other PMC-DR45 service manuals if exist.