DOWNLOAD Sony NWZ-S754 / NWZ-S755 Service Manual ↓ Size: 1.15 MB | Pages: 34 in PDF or view online for FREE

1-1. Outline
The unit has Digital Noise Cancelling function. Therefore, NC pa-
rameter data for each channel should be installed into NAND IC 
when replacing the MOTHER board.

Note 1: The EMMC Board is supplied as EMMC Board + MOTHER 

Board, because nobody knows the NC parameter data when the 
EMMC board is defective.

Note 2:  When the EMMC and MOTHER boards are replaced at the same 

time, NC parameter setting need not be executed.

The label having the NC parameter data for each channel is at-
tached on CPU (EM1) IC of complete MOTHER board (for SER-
VICE).

L= 13
R= 12

Note 1: Please use this Tool in Windows XP or later.
Note 2: Please install Windows Media Player 11 or later to make the unit 

recognize as MTP.

Note 3: Confi rm the method of obtaining the NC parameter setting tool to 

the service headquarters.

Procedure:
1.  Unzip the NC parameter setting tool to get “NWZS75X_NC-

Setting” folder.

2.  Copy the folder in step 1 under C Drive on PC.

Remark: Above folder in step 2 can be saved any drive as long as the 

folder path is with English (one byte character).
Described with the example that “the folder was saved under C 
Drive” on this service manual.

Note 1: Please use this tool after closing other application software.

Procedure:
1.  Turn on power of the WALKMAN, and connect it to PC con-

fi rm the drive letter information of WALKMAN (Example: F 
Drive).

2.  Start the command prompt application software, and change 

the folder pass to your desired folder (Example: c:\NW-
ZS75X_NCSetting).

 

3.  Input “updating-mtp” and press the Enter key on PC. If the fol-

lowing message is displayed, input “y” and press the Enter key 
on PC.

 

4.  If the following message is displayed, input the NC parameter 

data for L-ch confi rmed in “1-1. Outline” and press the Enter 
key on PC (Example: 13).

 

5.  If the following message is displayed, input the NC parameter 

data for R-ch confi rmed in “1-1. Outline” and press the Enter 
key on PC (Example: 12).

 

6.  If the following message is displayed, input the “yes” and  and 

press the Enter key on PC.

 

7.  The WALKMAN reboots automatically after the destination 

data is updated. After rebooting, check that connecting USB 
(MTP) is displayed on the liquid crystal display of the WALK-
MAN.

8.  Input “EXIT” to close the command prompt application soft-

ware.

9.  Disconnect the WALKMAN from PC.

Note 2:  Then, re-connect the main unit to PC again to delete the following 

two fi les inside NAND IC on the unit.

 

 NCGainValue.dat

 

 NW_WM_FW.UPG

 

After that, disconnect the main unit from PC.

NWZ-S754

Canadian

z

–

–

–

–

AEP, UK

z

z

z

z

–

East European

z

–

–

z

z

E, Australian

z

z

z

z

–

Mexican

z

–

–

–

–

Chinese

z

z

–

–

z

NWZ-S755

AEP, UK

z

z

z

z

–

East European

z

–

–

–

–

E, Australian

z

–

–

–

–

10. Enter the test mode referring to “1. SETTING THE TEST 

MODE” (page 17). Then, execute “4-10-1. Microphone gain 
(L-ch) adjustment” and “4-10-2. Microphone gain (R-ch) ad-
justment” (page 27), and check if the data is updated properly.

MATAPP (X.XX.XX)

POWER

AUDIO

VIDEO

VIDEO OUT

OTHER

CLESTE

DAC

DIREC

FM
NC

SHUTDOWN

EXITTEST

GAIN-L
GAIN-R
NCHPCHK

NC GAIN-Lcn

13

MODE

-1

NC GAIN-Rcn

12

MODE

-1

•  This set can be disassembled in the order shown below.

Note: Follow the disassembly procedure in the numerical order given.

4

1 

u 5.5)

3 

5 

6 

2 

2 

Note: When installing panel (rear) assy 
 

block, the position of switch and 

 

support (hold) is set and installed.