Sony NW-MS11 Service Manual ▷ View online
NW-MS11
8
3-6.
CONSOLE UNIT, SUB BOARD AND MAIN BOARD
3-7.
CONSOLE ASSY
4
console unit
1
connector (CN200)
6
main board
3
console flexible board
(CN300)
(CN300)
5
sub board
2
3
Remove the console board
in the direction of arrow
in the direction of arrow
A
.
Note: Make it sure to use the new adhesive sheet (LCD 1)
when the console assy is installed.
1
Raise up three claws
in the direction of arrow.
in the direction of arrow.
2
three claws
4
chassis (LCD)
adhesive sheet (LCD 1)
5
console assy
A
NW-MS11
9
3-8.
CONSOLE BOARD
1
window (LCD)
2
button (play)
3
console board
10
NW-MS11
SECTION 4
TEST MODE
[Preparation]
Checking consumed electric current is one of the items to check. Connect an ammeter before setting the test mode.
(Refer to the following figure)
(Refer to the following figure)
[Setting the Test Mode]
There are following two methods of entering the test mode.
Method 1:
Short the short lands (SL0120) on the MAIN board with a solder bridge, then turn on the power.
Method 2:
Turn on the power with the
Method 1:
Short the short lands (SL0120) on the MAIN board with a solder bridge, then turn on the power.
Method 2:
Turn on the power with the
[HOLD]
switch OFF. If the set is left as it is, the LCD display becomes on, and after for a while, it changes into
the sleep status (LCD off). Before the status of the display changes into the sleep status, turn ON the
[HOLD]
switch and press
Hs
t
[MEGA BASS]
t
Hs
t
[VOLUME--]
t
Hs
t
[VOLUME+]
keys in this order.
[Releasing the Test Mode]
There are following two methods of releasing the test mode.
In case of enter the test mode with the method 1:
Turn off the power and open the solder bridge on the short lands (SL0120) on the MAIN board.
In case of enter the test mode with the method 2:
Turn off the power.
In case of enter the test mode with the method 1:
Turn off the power and open the solder bridge on the short lands (SL0120) on the MAIN board.
In case of enter the test mode with the method 2:
Turn off the power.
R6901
R6902
C8004
C8509
R6903
R5001
R5003
C8008
R6018
R6027
R6028
R6035
R6037
C8016
C8014
C
R5002
R9015
C9007
R8103
R9019
R8102
R8607
R8104
R8608
R8105
R8110
C8006
1
L9007
IC8000
IC5000
X8000
56
43
SL0120
120 119 117 113 109 108 105 102 99
96 93
1
118 116 114 110 107 104 101 98
95 92
3
2 115 112 111 116 103 100 97
94 91
5
6
4
82
9
8
7
79
12
11 10
76
15
14 13
73
18
17 16
70
20
21 19
67
24
23 22
66
25
26 27
34
37
40 43 46
49
52 61
24
28 32
35
38
41 45 47
50
53 55
30
31 33
36
39
42 44 48
51
54 56
17
25
33
41
18
26
34
42
19
27
35
43
20
28
36
44
21
29
37
45
22
30
38
46
23
31
39
47
24
32
40
48
– MAIN BOARD (Conductor Side) –
battery terminal (+)
battery terminal
(–)
SL0120
+
–
ammeter
1.23Vdc
+
–
regulated dc
power supply
11
NW-MS11
[Flow Chart of Operations in the Test Mode]
[Items to Check in the Test Mode]
1. ROM/RAM Self-check
After entering the test mode, ROM/RAM self-check is performed automatically in the first place. By entering the test mode with key input,
however, no RAM check is performed.
1
however, no RAM check is performed.
1
Result of the ROM/RAM check is OK:
The LCD back light turns on, and version and destination is displayed automatically.
The LCD back light turns on, and version and destination is displayed automatically.
2
Result of the ROM check is NG:
“BAD ROM” is displayed on the LCD, and the LCD back light keeps blinking.
“BAD ROM” is displayed on the LCD, and the LCD back light keeps blinking.
3
Result of the RAM check is NG:
Nothing is displayed on the LCD, and the LCD back light keeps blinking
Nothing is displayed on the LCD, and the LCD back light keeps blinking
2. Display of Version and Destination
Version and destination are displayed as follows.
Every time the
[DISPLAY]
key is pressed, the display changes as “version and destination
t LCD all lit t LCD all off t version and
destination...”.
Also, pressing the
[VOLUME+]
key changes the mode to writing destination, and if pressing the
[VOLUME--]
key, the unit goes into the
sleep mode.
Enter the test mode
1. ROM/RAM Self-check
2. Display of version
and destination
3. Writing destination
(Checking voltage and
consumed electric current)
4. Checking the rated
voltage
5. Checking the LOW BATT
voltage
6. USB self-check
7. RTC self-check
8. Sleep mode
(Checking consumed electric current)
Waking up with the normal mode
(Waking up with the test mode, if
the short lands (SL0120) have
been short)
(Waking up with the test mode, if
the short lands (SL0120) have
been short)
[DISPLAY]
key
[DISPLAY]
key
[DISPLAY]
key
[MENU]
key
[MENU]
key
[MENU]
key
[MENU]
key
[MENU]
key
[VOLUME+]
key
[VOLUME--]
key
LCD all off
LCD all lit
any key
v0.09.05JP
display example
Click on the first or last page to see other NW-MS11 service manuals if exist.