Sony NW-HD5 (serv.man2) Service Manual ▷ View online
Copying is strictly prohibited
6
1-2. Generated Voltages List
Table.1-6 and Table.1-7 show the generated voltages lists of the unit.
Table.1-5 shows the differences of the generated voltages between NW-HD1 and NW-HD5.
Table.1-5 Differences between NW-HD1 and NW-HD5
Voltage Name
NW-HD1
NW-HD5
Remark
VG
6.0[V]
5.6[V]
-
REG_01
2.0[V]
1.9[V]
-
REG_03
Generated based on 1.8V
Generated based on REG_01.
1.8V
1.8V REGULATOR IC9003 is
mounted
mounted
1.8V REGULATOR IC is not
mounted. Instead of 1.8V, REG_01
is used.
mounted. Instead of 1.8V, REG_01
is used.
Not requiring 1.8V REGULATOR IC9003,
the design of NW-HD5 has the merits of parts
reduction and lower power consumption.
the design of NW-HD5 has the merits of parts
reduction and lower power consumption.
Table.1-6 Generated Voltages List - 1
Voltage Name
IC which generates the voltage
ICs which use the respective voltage
Test Point
BATT+
Rechargeable Lithium Ion Battery
CHARGE CONTROL IC9002
TP9010
DCIN6V (6[V])
AC power adapter
CHARGE CONTROL IC9002
-
VBUS
PC
-
USB CONTROLLER IC2001
-
CHARGE CONTROL IC9002
TP9018
VB
CHARGE CONTROL IC9002
-
POWER CONTROL IC9003
-
RTC IC9503
-
3.3V DC-DC CONVERTER IC9004
TP9003
VREF (1.275[V])
POWER CONTROL IC9003
POWER CONTROL IC9003
-
VG (5.6[V])
POWER CONTROL IC9003
POWER CONTROL IC9003
-
VSTB (VCO1: Wake-up mode)
POWER CONTROL IC9003
-
KEY SELECT SWITCH IC1001
-
KEY SELECT SWITCH IC1002
TP9014
VCO1 (2.4[V])
POWER CONTROL IC9003
-
MAIN SYSTEM CONTROLLER IC1003
-
Remote Controller
TP9015/TP4308
VC2 (1.2[V])
POWER CONTROL IC9003
-
MAIN SYSTEM CONTROLLER IC1003
-
MULTI INTERFACE IC7001
-
HP AMP. IC4301
TP9004
REG_01 (1.9[V])
POWER CONTROL IC9003
-
MAIN SYSTEM CONTROLLER IC1003
-
SUB SYSTEM CONTROLLER IC3001
-
MULTI INTERFACE IC7001
-
FLASH MEMORY IC1101
-
SD-RAM IC7002
-
BUFFER IC9502
-
RTC IC9503
TP9007
REG_03 (1.5[V])
POWER CONTROL IC9003
SUB SYSTEM CONTROLLER IC3001
TP9005
Copying is strictly prohibited
7
Table.1-7 Generated Voltages List - 2
Voltage Name
IC which generates the voltage
ICs which use the respective voltage
Test Point
3.3V
3.3V DC-DC CONVERTER IC9004
-
MAIN SYSTEM CONTROLLER IC1003
-
MULTI INTERFACE IC7001
-
SUB SYSTEM CONTROLLER IC3001
-
USB CONTROLLER IC2001
-
B+ SWITCH IC8001
-
G-SENSOR IC8000
-
BACKLIGHT DRIVER IC5001
-
LCD MODULE
-
3.3V_A
-
HP AMP. IC4301
-
2.4V REGULATOR IC4302
-
3.3V_HDD
-
Q2001 (Power Switch)
-
HDD DRIVE
TP9001/TP2001
2.4V_AD
2.4V REGULATOR IC4302
MAIN SYSTEM CONTROLLER IC1003
-
2.4V_DAC
MAIN SYSTEM CONTROLLER IC1003
SP1005
Copying is strictly prohibited
8
1-3. 3.3V/2.4V Generator Circuit
Fig.1-2 shows the 3.3V/2.4V generator circuit.
= 3.3V voltage =
The capacitor C9011 which is connected to Pin-33 of Power Control IC9003 is mounted for adjusting the output timing of Pin-34 of IC9003. This signal line becomes “H” in the
wake-up mode and “L” in the sleep mode. In this unit, this signal controls ON and OFF of 3.3V DC-DC CONVERTER IC9004.
When IC9003 is in the wake-up mode, CRST2 signal line becomes “H”. By this “H” signal, Q9009 turns “OFF” and “L” signal is input to Pin-1 [SHDN] of 3.3V DC-DC
CONVERTER IC9004. Then, IC9004 starts-up. When IC9004 starts up, IC9004 outputs the switching waveform from Pin-4 [SW]. Then, 3.3[V] is generated by the DC-DC
converter circuit composed of IC9004, L9003 and C9005. Then, the created voltage is supplied as the following 3 kinds of voltage.
3.3V voltage
3.3V_A voltage
3.3V_HDD voltage
= Mode Control of 3.3V DC-DC CONVERTER IC9004 =
3.3V DC-DC CONVERTER IC9004 has the lower power consumption mode and this mode is controlled by the signal output from pin-157[XHDD_PWR_CTL] of MULTI
INTERFACE IC7001. IC7001 outputs “H” signal when it recognizes that the following condition is satisfied.
= Condition that IC9004 enters the lower power consumption mode =
HDD drive is “OFF”
Table.1-8 Mode control of 3.3V DC-DC CONVERTER IC9004
IC7001 Pin-157 [XHDD_PWR_CTL]
Lower Power Consumption Mode
L
OFF
H
ON
= 2.4V voltage =
When 3.3V_A voltage is supplied, it is input to pin-4[VDD] and pin-1[CE] of +2.4V REGULATOR IC4302. Then IC4302 starts up. IC4302 generates +2.4[V] and outputs it from
pin-3[VOUT] as 2.4V_AD voltage and 2.4V_DAC voltage for the unit.
Copying is strictly prohibited
9
Fig.1-2 3.3V/2.4V Generator Circuit
Click on the first or last page to see other NW-HD5 (serv.man2) service manuals if exist.