Sony NW-E8P Service Manual ▷ View online
5
NW-E8P
12
Play status
During playback:
or
is
displayed alternately.
In stop mode:
is displayed.
While locating tracks: > or
.
is displayed.
While searching a point in a track:
M
or m is displayed.
When you play back songs for
more than 15 seconds, a wave
pattern is displayed.
more than 15 seconds, a wave
pattern is displayed.
Track
number
number
4
3
2
1
5
Changing the display mode
Press the DISPLAY button while the wave is
displayed during playback and the track
number is displayed.
displayed during playback and the track
number is displayed.
About the backlight
If you perform the following operation, the
backlight lights up for a few seconds.
If you perform the following operation, the
backlight lights up for a few seconds.
• Press the buttons (VOLUME+/--, DISPLAY,
P.MODE, MEGABASS/AVLS)
• Operate the Jog lever
Note
In a bright place, the backlight may not be
apparent.
In a bright place, the backlight may not be
apparent.
m
DISPLAY
button
button
Track
number
number
Volume
indication
indication
(Displayed
numerically.
Max. volume is
31)
numerically.
Max. volume is
31)
Play status
Play status
Listening to music with Network Walkman (continued)
On the display
1 AVLS indication (page 13)
The indication lights up while the AVLS
function is activated.
function is activated.
2 MEGA BASS indication (page 13)
The indication lights up while the MEGA
BASS function is activated.
BASS function is activated.
3 Battery remain indication (page 7)
The remaining battery power is
displayed.
displayed.
4 Play mode indication (page 14)
The selected play mode is displayed.
5
Play status/Track number display
The following information is displayed
according to the display mode.
The following information is displayed
according to the display mode.
15
Advanced Operations
Attaching the attachments
If your ears are small and you cannot attach the player correctly, use the supplied attachments.
Example for left ear
L
R
2
Lift its edge and turn it in the
direction of the arrow to remove it.
direction of the arrow to remove it.
1
Pull the edge of the attachment in
the direction of the arrow.
the direction of the arrow.
To remove the attachment
3
Press the point shown by the arrow to
secure it.
2
Turn the attachment to click into place.
Engage the pin in the slot as shown, and
insert the attachment.
insert the attachment.
1
pin
For left ear
For right ear
6
NW-E8P
SECTION 3
DISASSEMBLY
Note :
Follow the disassembly procedure in the numerical order given.
<R-CH section>
3-1. DRIVER ASSY (SP2), ARM LID (R), HOLDER LID (R)
3-1. DRIVER ASSY (SP2), ARM LID (R), HOLDER LID (R)
<R-CH section>
3-2. MAIN BOARD, POWER BOARD, LCD UNIT
3-2. MAIN BOARD, POWER BOARD, LCD UNIT
z
The equipment can be removed using the following procedure.
Driver ASSY (SP2), Arm lid (R), Holder lid (R)
<R-CH section>
<L-CH section>
Main board, Power board, LCD unit
Set
Driver ASSY (SP1), Arm lid (L), Holder lid (L)
8
6
3
1
LCD unit
Holder (R) ASSY
Arm lid (R)
4
Remove solder
(2 places)
2
Turn to clockwise
to release lock.
Red
Black
Black
7
Screw B1.7x5
5
Screws
B1.7x5
7
Screw
B1.7x5
Front plate
Red
Ear pad
Driver ASSY (SP2)
Driver ASSY
Marking (red)
Red
Glue
Black
• Connection of driver ASSY
Arm lid (R) (rear side)
• Installation of holder lid (R)
and arm lid (R)
Claw
Holder lid (R) (rear side)
Holder lid (R)
5
3
1
Holder (R) ASSY
2
LCD flexible board
(Power board: CN705)
Power board
LCD unit
Knob (HOLD)
Cord (4 core)
4
Remove solder
(4 places)
Red
Red/clear (rear side)
Green/clear
Green
CN704
CN702
Main board
HOLD switch
(S704)
(S704)
z
Caution during assembly
Align HOLD switch (S704) with
the position of knob (HOLD).
the position of knob (HOLD).
7
NW-E8P
<L-CH section>
3-3. DRIVER ASSY (SP1), ARM LID (L), HOLDER LID (L)
3-3. DRIVER ASSY (SP1), ARM LID (L), HOLDER LID (L)
9
6
3
1
Driver ASSY
Ear pad
Marking
(red)
(red)
Red
Glue
Black
• Connection of driver ASSY
Red
Black
Black
Green
Red
Red
Red/clear
Green/clear
Cord (4 core)
• Wiring of cord (4 core)
Arm lid (L)
Front plate
2
Turn to clockwise
to release lock.
5
Screws
B1.7x5
8
Screw
B1.7x5
8
Screws B1.7x5
7
Open the battery lid.
Driver ASSY (SP1)
Holder lid (L)
Holder (L) ASSY
MDD flexible board
4
Remove solder
(2 places)
Note:
When soldering,
paying attention as
holder (L) doesn’t
transform it by a heat.
When soldering,
paying attention as
holder (L) doesn’t
transform it by a heat.
• Installation of holder lid (L)
and arm lid (L)
Claw
Holder lid (L)
Lid (L), arm
(rear side)
(rear side)
8
NW-E8P
SECTION 4
TEST MODE
Setting the Test Mode
To enter the test mode, two methods are available :
1. Entering method with key input.
1. Entering method with key input.
Turn the HOLD switch to ON. While holding down the Bx key, press the following keys in the following order :
VOLUME +
VOLUME +
t VOLUME – t VOLUME – t VOLUME + t VOLUME – t MEGA BASS t MEGA BASS t DISPLAY
Note :
Push each key for less than 3 seconds.
2. Entering method by shorting the test point.
Solder brige the test point SL701 (TEST) on the main board and turn on the power.
Releasing the TEST mode
1. When test mode was entered with key input, turn off the power supply.
2. When test mode was entered by shorting the test point, turn off the power supply and open the solder brige of SL701 (TEST) on the main
2. When test mode was entered by shorting the test point, turn off the power supply and open the solder brige of SL701 (TEST) on the main
board.
Test mode
Short : Test mode
Open : Normal mode
Short : Test mode
Open : Normal mode
(
)
1
4
regulated
DC power supply
Connecting cable
supplied with the set
supplied with the set
USB Connector
(1-784-009-11 or 1-779-676-11)
Set
Battery terminal
CN701
(USB Connector)
regulated
DC power supply
LCD
Check
Ver. /
destination
display
All display
lit
(+)
(–)
All display
off
Flash memory
bad block
check
Bx
Bx
(+)
(–)
(+)
(–)
Destination
setting
Contrast
adjustment
(–)
Low voltage
check
(–)
Bx
Bx
(–)
High DC
detection
detection
check
Low DC
detection
check
(+)
Supply 0.9V DC to battery
terminal and press (–) key.
terminal and press (–) key.
Supply 1.24V DC to battery
terminal and 7V DC to USB
connector and press (+) key.
terminal and 7V DC to USB
connector and press (+) key.
Supply 1.24V DC to battery
terminal and 4V DC to USB
connector and press (+) key.
terminal and 4V DC to USB
connector and press (+) key.
Configuration of Test Mode
The test mode has the configuration given below.
Bx
: Play/stop key
(+)
: VOLUME + key
(–)
: VOLUME – key
Connection
C
C703
C704
R764
R769
R7
7
R705
R703
R767
R783
R7
7
R7
7
JC722
X701
TP702
TP3 TP701
TP703
(TEST)
IC820
CN701
USB
CONNECTOR
4
4
1
1
1
2
2
3
3
5
5
5
13
(13)
1-681-242-
P701
D781
MAIN BOARD (SIDE B)
Click on the first or last page to see other NW-E8P service manuals if exist.