Sony NW-E503 / NW-E505 / NW-E507 Service Manual ▷ View online
9
NW-E503/E505/E507
2
connector
1
sheet (connector)
3
five claws
4
connector
8
spacer
(VOL)
9
sheet
(shield)
6
spacer
(PWB)
0
MAIN board
5
organic EL indicator
module connector
2-6. MAIN BOARD
10
NW-E503/E505/E507
2
Remove the SW board
in the direction of the arrow.
3
SW board
1
two claws
6
organic EL indicator
module
4
adhesive sheet (panel)
5
two
buttons (top),
chassis
2-7. ORGANIC EL INDICATOR MODULE
11
NW-E503/E505/E507
SECTION 3
TEST MODE
STANDING PROCEDURE
Procedure 1: In HOLD state, while pushing Nx button, push
[REST].
When the test mode is set, the LCD display appears
as shown below.
When the test mode is set, the LCD display appears
as shown below.
Procedure 2: After starting up test mode, the following contents
can be checked.
TEST MODE
• Nx button
The KEY test mode is activated. All key inputs are completed,
then Nx button is pressed, restart. (Be aware that the
initialization is included on all key input.)
• [MENU] button
Change tuner (Fmax/Fmin).
• [DISP] button
Tuner off
• + > knob
Change charge mode (100 mA/500 mA).
• . – knob
Charge on/off.
• [GROUP] on state
LCD checked pattern.
• [GROUP] off state
“GROUP KEY OFF” appears.
• [GROUP ] knob
All LCD lights on.
• [GROUP ] knob
All LCD lights off.
• [VOL +] button
BEEP turns on.
• [VOL --] button
BEEP turns off.
• [ REPEAT SOUND] button
Initialized. (Turns to the factory preset state, time, volume setting
and so on.)
The music data, files and so on in the memory are not changed.
The KEY test mode is activated. All key inputs are completed,
then Nx button is pressed, restart. (Be aware that the
initialization is included on all key input.)
• [MENU] button
Change tuner (Fmax/Fmin).
• [DISP] button
Tuner off
• + > knob
Change charge mode (100 mA/500 mA).
• . – knob
Charge on/off.
• [GROUP] on state
LCD checked pattern.
• [GROUP] off state
“GROUP KEY OFF” appears.
• [GROUP ] knob
All LCD lights on.
• [GROUP ] knob
All LCD lights off.
• [VOL +] button
BEEP turns on.
• [VOL --] button
BEEP turns off.
• [ REPEAT SOUND] button
Initialized. (Turns to the factory preset state, time, volume setting
and so on.)
The music data, files and so on in the memory are not changed.
•
256M 1.00.04 G10
<
,
12
NW-E503/E505/E507
SECTION 4
DIAGRAMS
Note on Schematic Diagram:
• All capacitors are in
• All capacitors are in
µ
F unless otherwise noted. (p: pF) 50 WV
or less are not indicated except for electrolytics and tantalums.
• All resistors are in
Ω
and
1
/
4
W or less unless otherwise speci-
fied.
•
%
: indicates tolerance.
•
C
: panel designation.
•
: B+ Line.
• Voltages and waveforms are dc with respect to ground under
no-signal (detuned) conditions.
no mark : PLAY
no mark : PLAY
*
: Impossible to measure
• Voltages are taken with a VOM (Input impedance 10 M
Ω
).
Voltage variations may be noted due to normal production toler-
ances.
ances.
• Waveforms are taken with a oscilloscope.
Voltage variations may be noted due to normal production toler-
ances.
ances.
• Circled numbers refer to waveforms.
• Signal path.
E
: PLAY BACK
a
: DIGITAL OUT
k
: DIGITAL IN
d
: TUNER
F
: AUDIO
Note on Printed Wiring Board
•
•
X
: parts extracted from the component side.
•
Y
: parts extracted from the conductor side.
•
: Pattern from the side which enables seeing.
Caution:
Pattern face side: Parts on the pattern face side seen from
(Side A)
Pattern face side: Parts on the pattern face side seen from
(Side A)
the pattern face are indicated.
Parts face side:
Parts on the parts face side seen from
(Side B)
the parts face are indicated.
• MAIN board is multi-layer printed board.
However, the patterns of intermediate-layer have not been in-
cluded in the diagram.
cluded in the diagram.
*
Replacement of IC400 on MAIN board requires a special
tool.
tool.
• Lead Layouts
surface
CSP (Chip Size Package)
Lead layout of conventional IC
•
Waveforms
1
IC400
<zcm
(XTAL)
44.3 ns
2.2 Vp-p
500 mV/DIV, 20 ns/DIV
2
IC400
<zvz
(TX)
62.5
n
s
1 V/DIV, 20 ns/DIV
3.4 Vp-p
3
IC401
8
(OSCOUT)
16.3
µ
s
500 mV/DIV, 20
µ
s/DIV
1.5 Vp-p
Ver. 1.5
Click on the first or last page to see other NW-E503 / NW-E505 / NW-E507 service manuals if exist.