Sony NAS-E35HD / SS-CE35HD Service Manual ▷ View online
NAS-E35HD/SS-CE35HD
17
SECTION 4
TEST MODE
COLD RESET
The cold reset clears all data including preset data stored in the
memory to initial conditions. Execute this mode when returning
the set to the customer.
Procedure:
1. In the standby status, press the [
memory to initial conditions. Execute this mode when returning
the set to the customer.
Procedure:
1. In the standby status, press the [
?/1
] button to turn the power
on.
2. Press three buttons of [
x
], [ENTER] and at last [
?/1
] simulta-
neously.
3. The set enters standby status.
PANEL TEST MODE
Enter The Panel Test Mode
Procedure:
1. In the standby status, press the [
Procedure:
1. In the standby status, press the [
?/1
] button to turn the power
on.
2. Press three buttons of [BACK], [
x
], and [
Z
] simultaneously.
3. When the panel test mode is activated, LEDs and segments of
the fulorescent indicator tube are all turned on.
Version Check
Procedure:
1. In the panel test mode (all LEDs and segments of the fulores-
Procedure:
1. In the panel test mode (all LEDs and segments of the fulores-
cent indicator tube are turned on), press the [BACK] button.
2. On the fulorescent indicator tube, model name, destination,
MC version and its last updated date are displayed.
3. Each time [BACK] button is pressed, the display changes start-
ing from MC, GC, GENE, GNS, HDD, USB, CD, CDMA,
CDMB, ST, TA, TM and CLA version this order, and returns to
the MC version display.
CDMB, ST, TA, TM and CLA version this order, and returns to
the MC version display.
4. To release from this mode, press three buttons of [BACK],
[
x
], and [
Z
] simultaneously.
Key Test Mode
Procedure:
1. In the panel test mode (all LEDs and segments of the fulores-
Procedure:
1. In the panel test mode (all LEDs and segments of the fulores-
cent indicator tube are turned on), press the [ENTER] button.
2. The message “KEY0 VOL0” displayed. Whenever any but-
tons are pressed and the [VOLUME] dial is turned, the value is
changed.
changed.
3. To release from this mode, press three buttons of [BACK],
[
x
], and [
Z
] simultaneously.
CD SHIP MODE
This mode can run the CD sled motor optionally. Use this mode,
for instance, when cleaning the optical pick-up.
Procedure:
1. Press the [
for instance, when cleaning the optical pick-up.
Procedure:
1. Press the [
?/1
] button to turn the power on.
2. Confi rm there is no disc in all trays.
3. Press the [FUNCTION] button to select CD function.
4. Press two buttons of [OPTIONS] and [
3. Press the [FUNCTION] button to select CD function.
4. Press two buttons of [OPTIONS] and [
?/1
] simultaneously.
5. Set to the CD ship mode. (chucking on)
6. After blink “STANDBY”, “LOCK” is displayed, disconnect
6. After blink “STANDBY”, “LOCK” is displayed, disconnect
the AC plug.
CD TRAY LOCK
This mode is for the antitheft of CD disc in shop. (not for trans-
port)
Procedure:
1. Press the [
port)
Procedure:
1. Press the [
?/1
] button to turn the power on.
2. Press the [FUNCTION] button to select CD function.
3. Insert a disc.
4. While pressing the [
3. Insert a disc.
4. While pressing the [
x
] button, press the [
Z
] button for more 5
seconds.
5. The message “LOCKED” is displayed and the disc tray is
locked. (Even if exiting from this mode, the disc tray is still
locked)
locked)
6. If press the [
Z
] button to eject the disc, the message “LOCKED”
is displayed and can not eject the disc.
7. To release this lock, while pressing the [
x
] button, press the
[
Z
] button for 5 seconds again.
8. The message “UNLOCKED” is displayed and the disc tray is
unlocked.
CD POWER MANAGE
This mode is for switch the CD power supply on/off. Even if this
state pulls out AC plug, it is held.
Procedure:
1. Press the [
state pulls out AC plug, it is held.
Procedure:
1. Press the [
?/1
] button to turn the power on.
2. Press the [FUNCTION] button to select CD function.
3. Press the [
3. Press the [
?/1
] button again to turn the power off (standby).
4. After pressing the [DISPLAY] button on the remote com-
mander, while pressing the [
x
] button, press the [
?/1
] button.
5. It turns power on and display “CD POWER ON” or “CD
POWER OFF”.
CHANGE-OVER THE AM TUNING INTERVAL
(Except AEP, Russian and UK models)
The AM tuning interval can be changed over 9 kHz or 10 kHz.
Procedure:
1. Press the [
The AM tuning interval can be changed over 9 kHz or 10 kHz.
Procedure:
1. Press the [
?/1
] button to turn the power on.
2. Press the [TUNER/BAND] button to select TUNER (AM)
function.
3. Press the [
?/1
] button again to turn the power off (standby).
4. After pressing the [DISPLAY] button on the remote com-
mander, while pressing the [TUNE + M L] button, press
the [
the [
?/1
] button.
5. It turns power on and display “9k STEP” or “10k STEP”, and
thus the tuning interval is changed over.
Note: Never execute the item because the set might not operate
normally when the item being written, “Not used for the
servicing.” in each item is executed.
servicing.” in each item is executed.
Ver. 1.1
NAS-E35HD/SS-CE35HD
18
COMMON TEST MODE
Procedure:
1. Press the [
1. Press the [
?/1
] button to turn the power on.
2. Press three buttons of [
x
], [ENTER], and [
Z
] simultaneously.
3. It enters the common test mode and the “PLAY SLEEP” seg-
ment on the fl uorescent indicator tube blinks.
4. Each time the [VOLUME] dial is turned, “VOLUME MIN”
and “VOLUME MAX” are displayed.
5. Each time the [EQ] button on the remote commander is
pressed, “TONE MAX”, “TONE MIN” and “TONE FLAT”
are displayed.
are displayed.
6. To release from this mode, press the [
?/1
] button to turn the
power off.
HDD TEST MODE
The CDDB version display, custom DB initialization, HDD writ-
ing/reading test, HDD test data deletion, format, HDD setup and
initialization mode for factory can be executed in this mode.
ing/reading test, HDD test data deletion, format, HDD setup and
initialization mode for factory can be executed in this mode.
Enter The HDD Test Mode
Procedure:
1. In the standby status, press the [
Procedure:
1. In the standby status, press the [
?/1
] button to turn the power
on.
2. Press three buttons of [l m TUNE –], [m] and [Z] simul-
taneously.
3. When the HDD test mode is activated.
1. CDDB Version Display
The version of CDDB built into HDD is displayed.
Procedure:
1. Enter the HDD test mode.
2. Press the [M] [m] button to select the “CDDB Version”, and
The version of CDDB built into HDD is displayed.
Procedure:
1. Enter the HDD test mode.
2. Press the [M] [m] button to select the “CDDB Version”, and
press the [ENTER] button.
3. The version of CDDB is displayed on the fl uorescent indicator
tube.
2. Custom DB Initialization
The initialization of custom DB recorded in HDD is executed.
The initialization of custom DB recorded in HDD is executed.
Note: Not used for the servicing.
Procedure:
1. Enter the HDD test mode.
2. Press the [M] [m] button to select the “Custom Init”, and press
1. Enter the HDD test mode.
2. Press the [M] [m] button to select the “Custom Init”, and press
the [ENTER] button.
3. The
following
fi les in HDD are deleted.
• ROOT\SYSTEM\CCUDB\CCU.EDB
• ROOT\SYSTEM\CCUDB\CCU.IDX
• ROOT\SYSTEM\CCUDB\CCUTOC.IDX
• ROOT\SYSTEM\CCUDB\SCCU.EDB
• ROOT\SYSTEM\CCUDB\SCCU.IDX
• ROOT\SYSTEM\CCUDB\SCCUTOC.IDX
• ROOT\SYSTEM\CCUDB\CCU.IDX
• ROOT\SYSTEM\CCUDB\CCUTOC.IDX
• ROOT\SYSTEM\CCUDB\SCCU.EDB
• ROOT\SYSTEM\CCUDB\SCCU.IDX
• ROOT\SYSTEM\CCUDB\SCCUTOC.IDX
3. HDD Writing/Reading Test
The writing/reading of test data is done to HDD, and whether it
operates normally is checked.
Procedure:
1. Enter the HDD test mode.
2. Press the [M] [m] button to select the “HDD W/R Test”, and
The writing/reading of test data is done to HDD, and whether it
operates normally is checked.
Procedure:
1. Enter the HDD test mode.
2. Press the [M] [m] button to select the “HDD W/R Test”, and
press the [ENTER] button.
3. The writing reading of the test data is done to HDD, and the
result is displayed.
When the writing/reading of the test data ends normally, the
written test data is deleted.
• W/R Test OK : The writing/reading of the test data ended
written test data is deleted.
• W/R Test OK : The writing/reading of the test data ended
normally.
• W/R NG
: Abnormality occurred in the writing/reading
of the test data.
• Erase NG
: It failed in the deletion of the test data.
4. Format
The deletion of all folders and fi les in HDD is executed.
The deletion of all folders and fi les in HDD is executed.
Note 1: Not used for the servicing.
Note 2: When this mode is executed, all data including the SYSTEM fi le
Note 2: When this mode is executed, all data including the SYSTEM fi le
in HDD is deleted.
Procedure:
1. Enter the HDD test mode.
2. Press the [M] [m] button to select the “Format”, and press the
1. Enter the HDD test mode.
2. Press the [M] [m] button to select the “Format”, and press the
[ENTER] button.
3. All folders and fi les in HDD are deleted.
5. HDD Setup
The installation of initial data is executed from the USB memory
to HDD.
The installation of initial data is executed from the USB memory
to HDD.
Note 1: Not used for the servicing.
Note 2: The SYSTEM fi le and the DEMO tune are copied from USB
Note 2: The SYSTEM fi le and the DEMO tune are copied from USB
memory after all data in HDD is deleted with format when this
mode is executed, and HDD can be returned to the state of initial-
ization (It takes the time of about 80 minutes).
mode is executed, and HDD can be returned to the state of initial-
ization (It takes the time of about 80 minutes).
Procedure:
1. Connect the USB memory where initial data is recorded to the
1. Connect the USB memory where initial data is recorded to the
set.
2. Enter the HDD test mode.
3. Press the [M] [m] button to select the “Setup”, and press the
3. Press the [M] [m] button to select the “Setup”, and press the
[ENTER] button.
4. The following data is copied from the USB memory to HDD.
• ROOT\SYSTEM\TitleUpdater.exe
• ROOT\SYSTEM\TitleUpdaterVersion.txt
• ROOT\SYSTEM\UCODE.DAT
• ROOT\SYSTEM\CDDB\ecddb.idx
• ROOT\SYSTEM\CDDB\ecddb.mdt
• ROOT\SYSTEM\CDDB\elists.db
• ROOT\MUSIC\(File of description to “MUJIC\music.txt”)
• ROOT\SYSTEM\TitleUpdaterVersion.txt
• ROOT\SYSTEM\UCODE.DAT
• ROOT\SYSTEM\CDDB\ecddb.idx
• ROOT\SYSTEM\CDDB\ecddb.mdt
• ROOT\SYSTEM\CDDB\elists.db
• ROOT\MUSIC\(File of description to “MUJIC\music.txt”)
6. Initialization Mode For Factory
The user use areas other than the “Sony Demo” artist in HDD are
initialized, and the cold reset is executed.
Procedure:
1. Enter the HDD test mode.
2. Press the [M] [m] button to select the “FactoryPreset”, and
The user use areas other than the “Sony Demo” artist in HDD are
initialized, and the cold reset is executed.
Procedure:
1. Enter the HDD test mode.
2. Press the [M] [m] button to select the “FactoryPreset”, and
press the [ENTER] button.
3. Press the [M] [m] button to select the “OK?”, and press the
[ENTER] button.
4. All
folder/fi le in the following folders in HDD is deleted.
• ROOT\SYSTEM\CCUDB
• ROOT\MUSIC (excluding folder/fi le that belongs to “Sony
• ROOT\MUSIC (excluding folder/fi le that belongs to “Sony
Demo” artist)
5. After initialization ends, the cold reset is executed.
Ver. 1.1
Note: Never execute the item because the set might not operate
normally when the item being written, “Not used for the
servicing.” in each item is executed.
servicing.” in each item is executed.
NAS-E35HD/SS-CE35HD
19
HDD FACTORY SHIPMENT TEST MODE
The user use areas in HDD are initialized, and the cold reset is
executed.
executed.
Note: When this mode is executed, all the MUSIC data including the
DEMO tune in HDD is deleted (The SYSTEM fi le is not deleted).
Execute this mode after it notes it enough when executing it because
all the MUSIC data and CDDB updates that the user recorded are
deleted.
deleted.
Procedure:
1. In the standby status, press the [
1. In the standby status, press the [
?/1
] button to turn the power
on.
2. Press three buttons of [x], [BACK] and [HDD REC] simulta-
neously.
3. Press the [M] [m] button to select the “OK?”, and press the
[ENTER] button.
4. All
folder/fi le in the following folders in HDD is deleted.
• ROOT\SYSTEM\CCUDB
• ROOT\MUSIC
• ROOT\MUSIC
5. After initialization ends, the cold reset is executed.
Ver. 1.1
NAS-E35HD/SS-CE35HD
20
SECTION 5
ELECTRICAL CHECKS
Note:
1. CD Block is basically designed to operate without adjustment. There-
1. CD Block is basically designed to operate without adjustment. There-
fore, check each item in order given.
2. Use YEDS-18 disc (3-702-101-01) unless otherwise indicated.
3. Use an oscilloscope with more than 10 M
3. Use an oscilloscope with more than 10 M
Ω impedance.
4. Clean the object lens by an applicator with neutral detergent when the
signal level is low than specifi ed value with the following checks.
RF LEVEL CHECK
TP216 (RFACO)
CD board
oscilloscope
TP5 (VC)
Procedure:
1. Connect an oscilloscope TP216 (RFACO) and TP5 (VC) on
1. Connect an oscilloscope TP216 (RFACO) and TP5 (VC) on
the CD board.
2. Turn the power ON.
3. Load a disc (YEDS-18) and playback.
4. Confi rm that oscilloscope waveform is clear and check if RF
3. Load a disc (YEDS-18) and playback.
4. Confi rm that oscilloscope waveform is clear and check if RF
signal level is correct or not.
Note: Clear RF signal waveform means that the shape “ ◊ ” can be clearly
distinguished at the center of the waveform.
RF signal waveform
VOLT/DIV : 200 mV
TIME/DIV : 500 ns
TIME/DIV : 500 ns
level : 1.1 ± 0.3 Vp-p
E-F BALANCE (1 TRACK JUMP) CHECK
TP3 (TEI)
TP5 (VC)
TP5 (VC)
CD board
oscilloscope
Procedure:
1. Connect an oscilloscope to TP3 (TEI) and TP5 (VC).
2. Turn the power ON.
3. Load a disc (YEDS-18) and playback the number 5 track.
4. Confi rm that the level B and A (DC voltage) on the oscillo-
1. Connect an oscilloscope to TP3 (TEI) and TP5 (VC).
2. Turn the power ON.
3. Load a disc (YEDS-18) and playback the number 5 track.
4. Confi rm that the level B and A (DC voltage) on the oscillo-
scope waveform.
level = 1.3 ± 0.6 Vp-p symmetry
A (DC voltage)
center of
waveform
waveform
B
DVC
1 track jump waveform
CD SECTION
Connecting and Adjustment Location: CD board
TP3
(TEI)
(TEI)
TP5
(VC)
(VC)
TP216
(RFACO)
(RFACO)
– CD BOARD (CONDUCTOR SIDE) –
TUNER SECTION
FM AUTO STOP CHECK
generator
SET
+
75
Ω
Procedure:
1. Turn the power on.
2. Input the following signal from Signal Generator to FM an-
1. Turn the power on.
2. Input the following signal from Signal Generator to FM an-
tenna input directly.
Carrier frequency : A = 87.5 MHz, B = 98 MHz, C = 108 MHz
Deviation
Deviation
: 75 kHz
Modulation
: 1 kHz
ANT input
: 35 dBu (EMF)
Note: Please use 75 ohm “coaxial cable” to connect SG and the set. You
cannot use video cable for checking.
Please use SG whose output impedance is 75 ohm.
3. Set to FM tuner function and scan the input FM signal with
automatic scanning.
4. Confi rm that input Frequency of A, B and C detected and auto-
matic scanning stops.
The stop of automatic scanning means “The station signal is re-
ceived in good condition”.
Click on the first or last page to see other NAS-E35HD / SS-CE35HD service manuals if exist.