Sony MHC-VX333 (serv.man2) Service Manual ▷ View online
9
HCD-VX333
3-4. TAPE MECHANISM DECK
3-5. PANEL BOARD
1
Six screws
(+BVTP 2.6
×
8)
2
Deck, Mecha
1
Volume knob
2
Vol knob ring
4
Connector
13p (CN712)
Note: When attching the panel board,
refer to "Service Note" on page 4.
refer to "Service Note" on page 4.
6
PANEL board
3
5
Cut the seven melted-connection points with a cutting plier.
10
HCD-VX333
3-6. KEY BOARD
3-7. SUB TRANS BOARD, TRANS BOARD, SENSOR BOARD AND VIDEO OUT BOARD
Note: When attching the Key board,
refer to "Service Note" on page 4.
refer to "Service Note" on page 4.
2
KEY board
1
Cut the six melted-connection points with a cutting plier.
6
Two screws
(+BVTT 4
×
6 (S))
qf
Five screws
(+BVTP 3
×
8 TYPE2 N-S)
qg
Two screws
(+BVTT 3
×
6 (S))
qh
qj
Two screws
(+BVTP 3
×
8 TYPE2 N-S)
q;
Two screws
(+BVTP 3
×
8 TYPE2 N-S)
ql
Screw (+BVTP 3
×
8 TYPE2 N-S)
Back panel
7
Two screws
(+BVTT 4
×
6 (S))
8
Power transformer
(T911)
5
Connector 13P (CN915)
1
Connector 4p (CN2)(EXCEPT THAI)
Connector 2p (CN2)(THAI)
2
Connector 3p
(CN903)
9
Connector 2p
(CN504)
qd
SENSOR board
qs
Cover (Duct)
w;
VIDEO OUT board
qa
Screw
(+BVTP 3
×
8 TYPE2 N-S)
4
SUB TRANS
board
qk
Fan, DC (M961)
TRANS board
3
Two screws
(+BVTP 3
×
8 TYPE2 N-S)
11
HCD-VX333
3-8. MAIN BOARD AND POWER BOARD
3-9. BASE UNIT
4
Three screws (+BVTT 3
×
6 (S))
6
Two screws (+BVTT 3
×
6 (S))
7
Heat sink
3
Two screws
(+BVTP 3
×
16 TYPE2 IT-3)
1
Two screws (+BVTT 3
×
6 (S))
2
MAIN board
5
POWER AMP board
MAIN board
Optical pick-up
(KSM-213DCP/Z-NP)
(KSM-213DCP/Z-NP)
qa
9
Two screws
(+PTPWH M2.6, FLOATING))
1
Screw (+PTPWH M2.6, FLOATING)
q;
Screw (DIA. 12, FLOATING))
7
Two screws (+BVTP 2.6
×
8)
6
BD board
qs
Two insulators
(spring coil)
2
Holder (BU) assy
qs
Two insulators
(spring coil)
8
Two stoppers (BU)
3
Wire (flat type) 23p (CN101)
4
Wire (flat type) 16p (CN102)
5
Screw (+BVTP 2.6
×
8)
12
HCD-VX333
3-10. DRIVER BOARD, MOTOR BOARD AND ADDRESS SENSOR BOARD
9
Pull-out the disc tray.
4
Two
screws (+BVTP 2.6
×
8)
q;
Screw (+PTPWH 2.6
×
8)
qa
Tray
1
Screw (+BVTP 2.6
×
8)
qs
Screw (+BVTP 2.6
×
8)
6
Wire (flat type) 8p (CN721)
3
Wire (flat type)
8p (CN702)
8
MOTOR board
qd
ADDRESS SENSOR board
2
DRIVER board
5
Remove the two solderings of motor.
7
Connector 4p (CN722)
Click on the first or last page to see other MHC-VX333 (serv.man2) service manuals if exist.