Sony MDS-S9 Service Manual ▷ View online
49
MDS-S9
•
MAIN BOARD IC1 M30805MG-216GP (SYSTEM CONTROLLER)
Pin No.
Pin Name
I/O
Description
1
FL-DATA
O
Serial data output to the fluorescent indicator tube/LED driver (IC761)
2
FL-CLK
O
Serial data transfer clock signal output to the fluorescent indicator tube/LED driver (IC761)
3
A1 IN
I
Sircs remote control signal input terminal of the CONTROL A1II Not used (fixed at “H”)
4
RMC
I
Remote control signal input from the remote control receiver (IC781)
5 to 7
NC
O
Not used (open)
8
MUTE
O
Audio line muting on/off control signal output “L”: line muting on, “H”: line muting off
9
RESET
O
Reset signal output to the A/D, D/A converter (IC500) “L”: reset
10
LATCH
O
Serial data latch pulse signal output to the A/D, D/A converter (IC500)
11
LD-LOW
O
Loading motor drive voltage control signal output for the loading motor driver (IC440)
“H” active
“H” active
12
LDIN
O
Motor control signal output to the loading motor driver (IC440) “L” active *1
13
LDOUT
O
Motor control signal output to the loading motor driver (IC440) “L” active *1
Laser modulation selection signal output to the HF module switch circuit
Stop: “L”, Playback power: “H”,
Recording power:
14
MOD
O
15
BYTE
I
External data bus line byte selection signal input “L”: 16 bit, “H”: 8 bit (fixed at “L”)
16
CNVSS
—
Ground terminal
17
XCIN
I
Sub system clock input terminal (32.768 kHz) Not used (open)
18
XCOUT
O
Sub system clock output terminal (32.768 kHz) Not used (open)
19
RESET
I
System reset signal input from the regulator (IC400) “L”: reset
For several hundreds msec. after the power supply rises, “L” is input, then it changes to “H”
For several hundreds msec. after the power supply rises, “L” is input, then it changes to “H”
20
XOUT
O
Main system clock output terminal (10 MHz)
21
VSS
—
Ground terminal
22
XIN
I
Main system clock input terminal (10 MHz)
23
VCC
—
Power supply terminal (+3.3V)
24
NMI
I
Non-maskable interrupt input terminal “L” active (fixed at “H” in this set)
25
DQSY
I
Digital In U-bit CD format subcode Q sync (SCOR) input from the CXD2662R (IC151)
“L” is input every 13.3 msec Almost all, “H” is input
“L” is input every 13.3 msec Almost all, “H” is input
26
PDOWN
I
Power down detection signal input from the regulator (IC400)
“L”: power down, normally: “H”
“L”: power down, normally: “H”
27
SQSY
I
Subcode Q sync (SCOR) input from the CXD2662R (IC151)
“L” is input every 13.3 msec Almost all, “H” is input
“L” is input every 13.3 msec Almost all, “H” is input
28
KEYBD-CLK
I
Serial data transfer clock signal input from the key board Not used (fixed at “H”)
29
LDON
O
Laser diode on/off control signal output to the automatic power control circuit “H”: laser on
30
LIMIT-IN
I
Detection signal input from the sled limit-in detect switch (S101)
The optical pick-up is inner position when “L”
The optical pick-up is inner position when “L”
31
A1 OUT
O
Sircs remote control signal output terminal of the CONTROL A1II Not used (open)
2 sec
0.5 sec
*1 Loading motor (M103) control
LOADING
EJECT
BRAKE
STOP
LDIN (pin qs)
“L”
“H”
“L”
“H”
LDOUT (pin qd)
“H”
“L”
“L”
“H”
Terminal
Mode
50
MDS-S9
Pin No.
Pin Name
I/O
Description
32
XINT
I
Interrupt status input from the CXD2662R (IC151)
33
BEEP
O
Beep sound drive signal and headphone muting on/off control signal output terminal
Not used (open)
Not used (open)
34
LRCKI
O
L/R sampling clock signal (44.1 kHz) output to the CXD2662R (IC151)
35
WRPWR
O
Laser power selection signal output to the CXD2662R (IC151) and HF module switch circuit
“L”: playback mode, “H”: recording mode
“L”: playback mode, “H”: recording mode
36
I2CCLK
I/O
Serial data transfer clock signal input/output terminal for the IIC bus
37
I2CDAT
I/O
Serial data input/output terminal for the IIC bus
38
SWDT
O
Writing serial data signal output to the CXD2662R (IC151)
39
VCC
—
Power supply terminal (+3.3V)
40
SRDT
I
Reading serial data signal input from the CXD2662R (IC151)
41
VSS
—
Ground terminal
42
SCLK
O
Serial data transfer clock signal output to the CXD2662R (IC151)
43
REC-SW
I
Detection signal input from the recording position of over write head (HR901) detect switch
(S105) “L” recording mode
(S105) “L” recording mode
44
TX0 (CLIP)
O
Serial data output to the CXD2662R (IC151)
45
RX0 (CLIP)
I
Serial data input
46
CLK (CLIP)
O
Bit clock signal (2.8224 MHz) output to the CXD2662R (IC151)
47
DIG-RST
O
Reset signal output to the CXD2662R (IC151) and BH6519FS (IC141) “L”: reset
48
SENS
I
Internal status (SENSE) input from the CXD2662R (IC151)
49
PLAY-SW
I
Detection signal input from the playback position of over write head (HR901) detect switch
(S104) “L” playback mode
(S104) “L” playback mode
50
XLATCH
O
Serial data latch pulse signal output to the CXD2662R (IC151)
51
OUT-SW
I
Detection signal input from the loading-out detect switch (S103)
“L” at a load-out position, others: “H”
“L” at a load-out position, others: “H”
52
RDY
O
Not used (open)
53
ALE
O
Not used (open)
54
HOLD
O
Not used (open)
55
HLDA
O
Not used (open)
56
MNT2 (XBUSY)
I
Busy monitor signal input from the CXD2662R (IC151)
57
VSS
—
Ground terminal
58
MNT1 (SHOCK)
I
Track jump detection signal input from the CXD2662R (IC151)
59
VCC
—
Power supply terminal (+3.3V)
60
EEP-WP
O
Writing protect signal output to the EEPROM (IC195)
61
SDA
I/O
Two-way data bus with the EEPROM (IC195)
62
BCLK
O
Not used (open)
63
OE
O
Data reading strobe signal output to the flash memory “L” active Not used (open)
64
BHE
O
Not used (open)
65
WE
O
Writing enable signal output to the flash memory “L” active Not used (open)
66
SCL
O
Clock signal output to the EEPROM (IC195)
67
REFLECT SW
I
Detection signal input from the disc reflection rate detect switch (S102-1)
“L”: high reflection rate disc, “H”: low reflection rate disc
“L”: high reflection rate disc, “H”: low reflection rate disc
68
PROTECT SW
I
REC-proof claw detection signal input from the protect detect switch (S102-2)
“H”: write protect
“H”: write protect
69 to 71
CS0 to CS2
O
Chip select signal output to the flash memory “L” active Not used (open)
72, 73
A20, A19
O
Address signal output to the flash memory Not used (open)
74
VCC
—
Power supply terminal (+3.3V)
75
A18
O
Address signal output to the flash memory Not used (open)
51
MDS-S9
Pin No.
Pin Name
I/O
Description
76
VSS
—
Ground terminal
77 to 85
A17 to A9
O
Address signal output to the flash memory Not used (open)
86 to 89
SEL1 to SEL4
I
Not used (open)
90
WP
O
Writing protect signal output to the flash memory “L” active Not used (fixed at “L”)
91
VCC
—
Power supply terminal (+3.3V)
92
A8
O
Address signal output to the flash memory Not used (open)
93
VSS
—
Ground terminal
94 to 101
A7 to A0
O
Address signal output to the flash memory Not used (open)
102 to 113
D15 to D4
I/O
Two-way data bus with the flash memory Not used (open)
114
KEYBD-CLKCTL
O
Clock control signal output to the key board Not used (pull down)
115
I2CBUSY
I
Busy monitor signal input from the IIC bus
116
KEYBD-DAT
I
Serial data input from the key board Not used (fixed at “H”)
117
REC VOL A
O
Not used (open)
118
REC VOL B
O
Not used (open)
119 to 122
D3 to D0
I/O
Two-way data bus with the flash memory Not used (open)
123
JOG0
I
JOG dial pulse input from the rotary encoder (S713 . AMS >) (A phase input)
124
JOG1
I
JOG dial pulse input from the rotary encoder (S713 . AMS >) (B phase input)
125
LATCH
O
Not used (open)
126
REC
O
Power on/off control signal output terminal for the beep sound drive Not used (open)
127
COAX/OPT
O
Optical in or coaxial in selection signal output terminal “L”: optical in, “H”: coaxial in
Not used (open)
Not used (open)
128
FL-CS
O
Chip select signal output to the fluorescent indicator tube/LED driver (IC761)
129
I2CPOWER
I
Power supply detection signal input from the IIC bus
130
VSS
—
Ground terminal
131
STB
O
Relay drive signal output for the power on/off “L”: standby, “H”: power on
132
VCC
—
Power supply terminal (+3.3V)
133
IOP
I
Optical pick-up voltage detection signal input from the automatic power control circuit
134
DESTINATION
I
Destination setting input terminal Fixed at “L” in this set
135
MODEL
I
Model setting input terminal Fixed at “M” in this set
136
BEEP SW
I
Beep switch input terminal Not used (fixed at “L”)
137
KEY3
I
Key input terminal (A/D input) Not used (fixed at “H”)
138
KEY2
I
Key input terminal (A/D input) S721 to S724 and S726 (INPUT, PLAY MODE, REC MODE,
LEVEL/DISPLAY/CHAR, I/1) keys input
LEVEL/DISPLAY/CHAR, I/1) keys input
139
KEY1
I
Key input terminal (A/D input)
S711 to S715 (MENU/NO, YES, PUSH ENTER, CLEAR, Z) keys input
S711 to S715 (MENU/NO, YES, PUSH ENTER, CLEAR, Z) keys input
140
AVSS
—
Ground terminal (for analog system )
141
KEY0
I
Key input terminal (A/D input) S701 to S705 (z, x, M, m, u) keys input
142
VREF
I
Reference voltage (+3.3V) input terminal (for A/D converter)
143
AVCC
—
Power supply terminal (+3.3V) (for analog system )
144
NC
O
Not used (pull down)
52
MDS-S9
7-1. CASE SECTION
SECTION 7
EXPLODED VIEWS
• Items marked “*” are not stocked since they
are seldom required for routine service. Some
delay should be anticipated when ordering
these items.
delay should be anticipated when ordering
these items.
• The mechanical parts with no reference num-
ber in the exploded views are not supplied.
• Hardware (# mark) list and accessories and
packing materials are given in the last of the
electrical parts list.
electrical parts list.
NOTE:
• -XX and -X mean standardized parts, so they
may have some difference from the original
one.
one.
• Color Indication of Appearance Parts
Example:
KNOB, BALANCE (WHITE) . . . (RED)
KNOB, BALANCE (WHITE) . . . (RED)
↑
↑
Parts Color Cabinet's Color
The components identified by
mark 0 or dotted line with mark
mark 0 or dotted line with mark
0 are critical for safety.
Replace only with part number
specified.
Replace only with part number
specified.
Ref. No.
Part No.
Description
Remark
Ref. No.
Part No.
Description
Remark
1
1-681-806-11 PT BOARD
2
4-228-643-11 SCREW (+BVTTWH M3), STEP
3
3-363-099-21 SCREW (CASE 3 TP2)
4
4-229-363-51 CASE
5
1-792-811-11 WIRE (FLAT TYPE) (23 CORE)
6
1-792-812-11 WIRE (FLAT TYPE) (27 CORE)
0 7
1-777-071-61 CORD, POWER
* 8
3-703-244-00 BUSHING (2104), CORD
9
4-235-438-01 PANEL, BACK
10
A-4726-240-A MAIN BOARD, COMPLETE
11
4-965-822-01 FOOT
13
4-221-887-11 SCREW, +PTTWH (M3) (S) TITE
14
4-228-689-01 INSULATOR
* 15
1-569-972-21 SOCKET, SHORT 2P
0 TR900
1-435-544-11 TRANSFORMER, POWER
not supplied
MDM-7A
Front panel section
1
13
2
not
supplied
supplied
TR900
3
4
#3
#3
#3
#3
#3
5
6
3
8
10
9
15
11
14
14
14
14
7
A
A
B
B
Click on the first or last page to see other MDS-S9 service manuals if exist.