DOWNLOAD Sony MDS-JE630 Service Manual ↓ Size: 3.98 MB | Pages: 64 in PDF or view online for FREE

– 21 –

(
P

SYNC

A.SPACE

OVER

B

A-

TRACK

DISC

SLEEP

MONO

When Off

Contents

Display

When Lit

During continuous playback (CLV: ON)

Tracking servo OFF

Recording mode ON

CLV low speed mode

ABCD adjustment completed

Tracking offset cancel ON

Tracking auto gain OK

Focus auto gain OK

Pit

High reflection

CLV-S

CLV LOCK

STOP (CLV: OFF)

Tracking servo ON

Recording mode OFF

CLV normal mode

Tracking offset cancel OFF

Groove

Low reflection

CLV-A

CLV UNLOCK

– 22 –

• Check and adjust the MDM and MBU as follows.

The procedure changes according to the part replaced

• Abbreviation

OP

: Optical pick-up

OWH : Overwrite head

• Temperature compensation offset check
• Laser power check
• Traverse check
• Focus bias check
• C PLAY check
• Self-recording/playback check

Parts Replacement and Repair

NG

Has the OWH been replaced?

NO

OK

NO

NO

NO

Has OP, IC171, IC101, or 
IC121 been replaced?

YES

YES

Initial setting of the adjustment value

Has OP or IC171 been replaced?

YES

IOP information recording
(IOP value labeled on OP)

Has IC171 or D101 
been replaced?

YES

Temperature compensation offset adjustment

• Laser power adjustment
• Traverse adjustment
• Focus bias adjustment
• Error rate adjustment
• Focus bias check
• Auto gain adjustment

Check the sled and spindle 
mechanisms. 
Other causes can be suspected.

– 23 –

To check the emission of the laser diode during adjustments, never
view directly from the top as this may lose your eye-sight.

As the laser diode in the optical pick-up is easily damaged by static
electricity, solder the laser tap of the flexible board when using it.
Before disconnecting the connector, desolder first. Before con-
necting the connector, be careful not to remove the solder. Also
take adequate measures to prevent damage by static electricity.
Handle the flexible board with care as it breaks easily.

1. When replacing the following parts, perform the adjustments

and checks with 

¬ in the order shown in the following table.

pick-up

flexible board

laser tap

Optical

Pick-up

BD Board

IC101, IC121

D101

IC171

¬

G

¬

¬

1. Initial setting of

adjustment value

2. Recording of IOP

information
(Value on the
pick-up label)

3. Temperature

compensation
offset adjustment

4. Laser power

adjustment

5. Traverse

adjustment

6. Focus bias

adjustment

7. Error rate check

8. Auto gain output

level adjustment

IC192

G

¬

G

¬

G

G

¬

¬

G

G

G

¬

G

¬

¬

¬

¬

G

¬

¬

G

¬

G

¬

¬

G

¬

G

¬

¬

G

¬

G

¬

¬

G

2. Set the test mode when performing adjustments.

After completing the adjustments, release the test mode.
Perform the adjustments and checks in “group S” of the test
mode.

3. Perform the adjustments to be needed in the order shown.

4. Use the following tools and measuring devices.

• Check Disc (MD) TDYS-1

(Part No. 4-963-646-01)

• TEST DISK (MDW-74/AU-1) (Part No. 8-892-341-41)
• Laser power meter LPM-8001 (Part No. J-2501-046-A)

or MD Laser power meter 8010S (Part No. J-2501-145-A)

• Oscilloscope (Measure after performing CAL of prove)
• Digital voltmeter
• Thermometer
• Jig for checking BD board waveform

(Part No. : J-2501-149-A)

5. When observing several signals on the oscilloscope, etc.,

make sure that VC and ground do not connect inside the oscil-
loscope.
(VC and ground will become short-circuited)

6. Using the above jig enables the waveform to be checked with-

out the need to solder.
(Refer to Servicing Notes on page 6)

7. As the disc used will affect the adjustment results, make sure

that no dusts nor fingerprints are attached to it.

When performing laser power checks and adjustment (electrical
adjustment), use of the new MD laser power meter 8010S (Part
No. J-2501-145-A) instead of the conventional laser power meter
is convenient.
It sharply reduces the time and trouble to set the laser power meter
sensor onto the objective lens of optical pick-up.

* This disc is used in focus bias adjustment and error rate check.

The following describes how to create a continuous recording
disc.

1. Insert a disc (blank disc) commercially available.
2. Turn the 

[        AMS        ]

 knob and display “CREC MODE”.

(C31)

3. Press the 

[YES]

 button again to display “CREC MID”.

Display “CREC (0300)” and start to recording.

4. Complete recording within 5 minutes.
5. Press the 

[MENU/NO]

 button and stop recording .

6. Press the 

[     EJECT]

 button and remove the disc.

The above has been how to create a continuous recorded data for
the focus bias adjustment/check and MO error rate check.

• Be careful not to apply vibration during continuous recording.

±

≠

§

– 24 –

±

≠

These checks are performed before replacing parts according to
“approximate specifications” to determine the faulty locations. For
details, refer to “Checks Prior to Parts Replacement and Adjust-
ments” (See page 8).

When performing adjustments, set the internal temperature and
room temperature of 22 

°

C to 28 

°

C.

Checking Procedure:
1. Turn the 

[        AMS        ]

 knob to display “TEMP CHECK”

(C01).

2. Press the 

[YES]

 button.

3. “T=@@(##) [OK” should be displayed. If “T=@@ (##) [NG”

is displayed, it means that the results are bad.
(@@ indicates the current value set, and ## indicates the value
written in the non-volatile memory)

Before checking, check the IOP value of the optical pick-up.
(Refer to 8. Recording and Displaying the IOP Information)

Checking Procedure:
1. Set the laser power meter on the objective lens of the optical

pick-up. (When it cannot be set properly, press the

0  but-

ton or

) button to move the optical pick-up)

Connect the digital voltmeter to CN110 pin 5 (I+3V) and
CN110 pin 4 (IOP) on the BD board.

2. Then, turn the 

[        AMS        ]

 knob to display “LDPWR

CHECK” (C02).

3. Press the 

[YES]

 button once to display “LD 0.9 mW $ 

”.

Check that the reading of the laser power meter become 0.84
to 0.92 mW.

4. Press the 

[YES]

 button once more to display “LD 7.0 mW $

”. Check that the reading the laser power meter and digital

voltmeter satisfy the specified value.

Specified Value:
Laser power meter reading : 7.0 ± 0.2 mW
Digital voltmeter reading : Value on the optical pick-up label

±10%

5. Press the 

[MENU/NO]

 button to display “LDPWR CHECK”

and stop the laser emission.
(The 

[MENU/NO]

 button is effective at all times to stop the

laser emission)

±

≠

Optical pick-up
objective lens

laser
power meter

+
–

BD board

digital voltmeter

CN110 pin 

5

 (I +3V)

CN110 pin 

4

 (IOP)

[      ]

[      ]

KMS260A

27X40
B0825

lOP=82.5 mA in this case
lOP (mA) = Digital voltmeter reading (mV)/1 (

Ω

)

(Optical pick-up label)

After step 4, each time the 

[YES]

 button is pressed, the display

will be switched “LD 0.7 mW $ 

”, “LD 6.2 mW $ 

”, and

“LD Wp                 $ 

”. Nothing needs to be performed here.

Checking Procedure:
1. Connect an oscilloscope to CN110 pin 3 (TEO) and CN110

pin 1 (VC) on the BD board.

2. Load a disc (any available on the market). (Refer to Note 1)
3. Press the

) button to move the optical pick-up outside the

pit.

4. Turn the 

[        AMS        ]

 knob to display “EF MO CHECK”

(C03).

5. Press the 

[YES]

 button to display “EFB = 

 MO-R”.

(Laser power READ power/Focus servo ON/tracking servo
OFF/spindle (S) servo ON)

6. Observe the waveform of the oscilloscope, and check that the

specified value is satisfied. Do not turn the

[        AMS        ]

knob.
(Read power traverse checking)

Traverse Waveform

7. Press the 

[YES]

 button to display “EFB = 

 MO-W”.

8. Observe the waveform of the oscilloscope, and check that the

specified value is satisfied. Do not turn the 

[        AMS        ]

knob.
(Write power traverse checking)

Traverse Waveform

+
–

oscilloscope

(DC range)

V: 0.1 V/div
H: 10 ms/div

BD board

CN110 pin 

3

 (TEO)

CN110 pin 

1

 (VC)

[      ]

±

≠

±

≠

A

B

VC

Specified value : Below 10% offset value

Offset value (%) =                  X 100  

I

A – B

I

2 (A + B)

A

B

VC

Specified value : Below 10% offset value

Offset value (%) =                  X 100  

I

A – B

I

2 (A + B)

±

≠

+
–

oscilloscope

(DC range)

10 pF

330 k 

Ω

CN110 pin 

3

 (TEO)

CN110 pin 

1

 (VC)

BD board

Data will be erased during MO reading if a recorded disc is
used in this adjustment.

If the traverse waveform is not clear, connect the oscilloscope
as shown in the following figure so that it can be seen more
clearly.