DOWNLOAD Sony MDS-JE470 Service Manual ↓ Size: 3.85 MB | Pages: 70 in PDF or view online for FREE

6

The special jig (J-2501-196-A) is useful for checking the waveform of the BD board. The names of terminals and the checking items to be
performed are shown as follows.

GND : Ground
I+3V : For measuring IOP (Check the deterioration of the optical pick-up laser)
IOP : For measuring IOP (Check the deterioration of the optical pick-up laser)
TE

: TRK error signal (Traverse adjustment)

VC

: Reference level for checking the signal

RF

: RF signal (Check jitter)

FE

: Focus error signal

7

The Iop value labeled on the optical pick-up can be recorded in the non-volatile memory. By recording the value, it will eliminate the need to
look at the value on the label of the optical pick-up. When replacing the optical pick-up or non-volatile memory (IC195 of BD board), record
the Iop value on the optical pick-up according to the following procedure.

Record Precedure:
1. While pressing the  l AMS L  knob and  x  button, connect the power plug to the outlet, and release the  l AMS L  knob and

x  button.

2. Rotate the  l AMS L  knob to display “[Service]”, and press the  YES  button.
3. Rotate the  l AMS L  knob to display “Iop Write” (C05), and press the  YES  button.
4. The display becomes “Ref=@@@.@” (@ is an arbitrary number) and the numbers which can be changed will blink.
5. Input the Iop value written on the optical pick-up.

To select the number : Rotate the  l AMS L  knob.
To select the digit

: Press the  l AMS L  knob.

6. When the  YES  button is pressed, the display becomes “Measu=@@@.@” (@ is an arbitrary number).
7. As the adjustment results are recorded for the 6 value. Leave it as it is and press the  YES  button.
8. “Complete!” will be displayed momentarily. The value will be recorded in the non-volatile memory and the display will become “Iop

Write”.

9. Press the  REPEAT  button to complete.

Display Precedure:
1. While pressing the  l AMS L  knob and  x  button, connect the power plug to the outlet, and release the  l AMS L  knob and

x  button.

2. Rotate the  l AMS L  knob to display “[Service]”, and press the  YES  button.
3. Rotate the  l AMS L  knob to display “Iop Read” (C26).
4. “@@.@/##.#” is displayed and the recorded contents are displayed.

@@.@ : indicates the Iop value labeled on the optical pick-up.
##.#

: indicates the Iop value after adjustment

5. To end, press the  l AMS L  button or  MENU/NO  button to display “Iop Read”. Then press the  REPEAT  button.

8

There are two types of the optical pick-up block in this model.
These are compatible except  for the laser power.
Check the type of the optical pick-up block before replacement.
Ajdust  following items after replacing the optical pick-up block.
• 5-6-2. Laser Power Check (See page 28)
• 5-10. LASER POWER ADJUSTMENT (See page 31)

Differences

KMS-260B

       KMS-260E

Color of the adhesive agent at PDIC portion

Pink

White

Form of FPC retainer plate

Close the hole on SL base

Not close the hole on SL base

APC variable resistor

Small volume (2 type)

Big variable resistor (3 type) and chip resistor (Fig. A)

Small variable resistor (2 type) and chip resistor (Fig. B)

Fig. B type is for repair.

• Abbreviation

260B: KMS-260B model

260E: KMS-260E model

(Fig A)

(Fig B)

CHIP

3 type variable
resistor

2 type variable
resistor

CHIP

Hold on SL base

Hold on SL base

FPC retainer plate

FPC retainer plate

APC variable
resistor

Adhesive agent at 
PDIC portion

Adhesive agent at 
PDIC portion

9

Before performing repairs, perform the following checks to determine the faulty locations up to a certain extent.
Details of the procedures are described in “5 Electrical Adjustments”.

• 5-6-2. Laser power check (see page 28)
• 5-6-3. Iop Compare (see page 28)
• 5-6-4. Auto Check (see page 29)

Note:
The criteria for determination above is intended merely to determine if satisfactory or not, and does not serve as the specified value for
adjustments.
When performing adjustments, use the specified values for adjustments.

The system microprocessor can be reset in the following procedure.
Use these procedure when the unit cannot be operated normally due to the overrunning of the microprocessor, etc.
Procedure :
Remove the short-pin attached to CN406, and then attach it again.

@

CN406