DOWNLOAD Sony MDS-JB930 Service Manual ↓ Size: 5.28 MB | Pages: 74 in PDF or view online for FREE

57

Pin No.

Pin Name

I/O

Description

89

FRDR

O

Focus servo drive PWM signal (–) output to the BH6511FS (IC152)

90

FS4

O

Clock signal (176.4 kHz) output terminal (X’tal system)    Not used (open)

91

SRDR

O

Sled servo drive PWM signal (–) output to the BH6511FS (IC152)

92

SFDR

O

Sled servo drive PWM signal (+) output to the BH6511FS (IC152)

93

SPRD

O

Spindle servo drive PWM signal (–) output to the BH6511FS (IC152)

94

SPFD

O

Spindle servo drive PWM signal (+) output to the BH6511FS (IC152)

95

FGIN

I (S)

96

TEST1

I

97

TEST2

I

98

TEST3

I

99

DVSS

—

Ground terminal (digital system)

100

EFMO

O

EFM signal output terminal when recording mode

* I (S) stands for schmitt input, I (A) for analog input, O (3) for 3-state output, and O (A) for analog output in the column I/O.

Input terminal for the test (fixed at “L”)

58

•

Pin No.

Pin Name

I/O

Description

1

JOG1

I

Jog dial pulse input from the rotary encoder (S713  

≠ AMS ±)    B phase input

2

JOG0

I

Jog dial pulse input from the rotary encoder (S713  

≠ AMS ±)    A phase input

3

C1

O

Monitor output terminal for the test    C1 error rate is output when test mode

4

ADER

O

Monitor output terminal for the test    ADER is output when test mode

5

SQSY

I

Subcode Q sync (SCOR) input from the CXD2656R (IC121)
“L” is input every 13.3 msec    Almost all, “H” is input

6

RMC

I

Remote control signal input from the remote control receiver (IC761)

7

AIN1

I

Sircs remote control signal input of the CONTROL A1 II

8

BYTE

I

External data bus line byte selection signal input    “L”: 16 bit, “H”: 8 bit (fixed at “L”)

9

CNVSS

—

Ground terminal

10

XT-IN

I

Sub system clock input terminal (32.768 kHz)

11

XT-OUT

O

Sub system clock output terminal (32.768 kHz)

12

S.RST

I

System reset signal input from the LA5632 (IC700)    “L”: reset
For several hundreds msec. after the power supply rises, “L” is input, then it changes to “H”

13

XOUT

O

Main system clock output terminal (10 MHz)

14

GND

—

Ground terminal

15

XIN

I

Main system clock input terminal (10 MHz)

16

+3.3V

—

Power supply terminal (+3.3V)

17

NMI

I

Non-maskable interrupt input terminal (fixed at “H” in this set)

18

DQSY

I

Digital In U-bit CD format subcode Q sync (SCOR) input from the CXD2656R (IC121)
“L” is input every 13.3 msec    Almost all, “H” is input

19

P.DOWN

I

Power down detection signal input terminal    “L”: power down, normally: “H”

20

KBCLKIN

I

Serial data transfer clock signal input from the key board

21

KBDTIN

I

Serial data input from the key board

22

NC

O

Not used (open)

23

XINT

I

Interrupt status input from the CXD2656R (IC121)

24 to 26

NC

O

Not used (open)

27

KBCLKOUT

O

Serial data transfer clock signal output to the key board

28 to 30

NC

O

Not used (open)

31

SWDT

O

Writing data output to the CXD2656R (IC121), A/D converter (IC100) and D/A converter 
(IC200)

32

SRDT

I

Reading data input from the CXD2656R (IC121)

33

SCLK

O

Serial clock signal output to the CXD2656R (IC121), A/D converter (IC100) and D/A converter 
(IC200)

34

FLCS

O

Chip select signal output to the FL/LED driver (IC771)

35

FLDATA

O

Serial data output to the FL/LED driver (IC771)

36

NC

I

Not used (fixed at “L”)

37

FLCLK

O

Serial data transfer clock signal output to the FL/LED driver (IC771)

38

NC

O

Not used (open)

39

CLKO

O

Not used (open)

40

ADLATCH

O

Serial data latch pulse signal output to the A/D converter (IC100)

41

NC

I

Not used (fixed at “L”)

42

DVOL0

I

Jog dial pulse input from the rotary encoder (RV760 REC LEVEL)    A phase input

43

DVOL1

I

Jog dial pulse input from the rotary encoder (RV760 REC LEVEL)    B phase input

44, 45

NC

O

Not used (open)

46

NC

I

Not used (fixed at “H”)

59

Pin No.

Pin Name

I/O

Description

47

NC

O

Not used (open)

48

CSET0

I

Destination setting terminal (US, Canadian models: fixed at “L”, AEP, UK models: fixed at “H”)

49

CSET1

I

Destination setting terminal (US, Canadian models: fixed at “H”, AEP, UK models: fixed at “L”)

50

730/930

I

Setting terminal for the model (fixed at “H” in this set)

51

NC

I

Not used (fixed at “H”)

52

MNT2 (XBUSY)

I

Busy signal input from the CXD2656R (IC121)

53

DIG-RST

O

Reset signal output to the CXD2656R (IC121) and BH6511FS (IC152)    “L”: reset

54

MNT1 (SHOCK)

I

Track jump detection signal input from the CXD2656R (IC121)

55

SENS

I

Internal status (SENSE) input from the CXD2656R (IC121)

56

LDON

O

Laser diode on/off control signal output to the automatic power control circuit    “H”: laser on

57

REFLECT

I

Detection input from the disc reflection rate detect switch (S102)
“L”: high reflection rate disc, “H”: low reflection rate disc

58

PROTECT

I

Rec-proof claw detect input from the protect detect switch (S102)    “H”: write protect

59

WR-PWR

O

Laser power select signal output to the CXD2656R (IC121) and HF module switch circuit
“L”: playback mode, “H”: recording mode

60

MNT3 (SLOCK)

I

Spindle servo lock status monitor signal input from the CXD2656R (IC121)

61

SDA

I/O

Two-way data bus with the EEPROM (IC171)

62

+3.3V

—

Power supply terminal (+3.3V)

63

NC

I

Not used (fixed at “L”)

64

GND

—

Ground terminal

65

SCTX

O

Recording data output enable signal output to the CXD2656R (IC121) and overwrite head
driver (IC181)    Writing data transmission timing output (Also serves as the magnetic head on/off 
output)

66

SCL

O

Clock signal output to the EEPROM (IC171)

67

MNT0 (FOK)

I

Focus OK signal input from the CXD2656R (IC121)
“H” is input when focus is on (“L”: NG)

68

LIMIT-IN

I

Detection input from the sled limit-in detect switch (S101)
The optical pick-up is inner position when “L”

Laser modulation select signal output to the HF module switch circuit

Stop: “L”, Playback power: “H”,

Recording power:

69

MOD

O

70

XLATCH

O

Serial data latch pulse signal output to the CXD2656R (IC121)

71

NC

I

Not used (fixed at “L”)

72

REC/PB

I

Not used (fixed at “L”)

73

PACK-IN

I

Detection input from the disc detect switch    Not used (fixed at “L”)

74

PB-P

I

Detection input from the playback position detect switch (S604)    “L” active

75

CHACK IN

I

Detection input from the disc chucking-in detect switch    “L”: chucking
Not used (fixed at “H”)

76

PACK-OUT

I

Detection input from the loading-out detect switch (S602)
“L” at a load-out position, others: “H”

77

REC-P

I

Detection input from the recording position detect switch (S601)    “L” active

2 sec

0.5 sec

60

Pin No.

Pin Name

I/O

Description

78

LDIN

O

Motor control signal output to the loading motor driver (IC400)    “L” active    *1

79

LDOUT

O

Motor control signal output to the loading motor driver (IC400)    “L” active    *1

80

LD-LOW

O

Loading motor drive voltage control signal output for the loading motor driver (IC400)
“H” active

81

NC

I

Not used (fixed at “L”)

82

A1OUT

O

Sircs remote control signal output of the CONTROL A1 II

83

MUTE

O

Audio line muting on/off control signal output terminal    “L”: line muting on

84

STB

O

Strobe signal output to the power supply circuit    “L”: standby mode, “H”: power on

85

COAX/XOPT

O

Optical in 1/2 or coaxial in selection signal output to the digital input selector (IC300)
“L”: OPT 1/2, “H”: COAXIAL

86

OPT2/XOPT1

O

Optical in 1 or optical in 2 selection signal output to the digital input selector (IC300)
“L”: OPT 1, “H”: OPT 2

87

DALATCH

O

Serial data latch pulse signal output to the D/A converter (IC200)

88

DARST

O

Reset signal output to the A/D converter (IC100) and D/A converter (IC200)    “L”: reset

89

LED0

O

LED drive signal output terminal    Not used (pull down)

90

LED1

O

LED drive signal output terminal    Not used (pull down)

91

TIMER

I

TIMER switch (S751) input terminal (A/D input)
“L”: PLAY, “H”: REC (OFF: center voltage)

92

SOURCE

I

INPUT switch (S741) input terminal (A/D input)

93

KEY3

I

Key input terminal (A/D input)    S731 (PITCH CONTROL key input)

94

KEY2

I

Key input terminal (A/D input)    S721 to S724, S732 and S733 (DISPLAY/CHAR, SCROLL, 
PLAY MODE, I/

u, FILTER, TIME keys input)

95

KEY1

I

Key input terminal (A/D input)    S711 to S714 and S716 (MENU/NO, YES, PUSH ENTER,  
EJECT 

§ keys input)

96

AVSS

—

Ground terminal

97

KEY0

I

Key input terminal (A/D input)    S701 to S706 (REC 

r, p, ), 0, P, · keys input)

98

VREF

I

Reference voltage (+3.3V) input terminal (for A/D converter)

99

+3.3V

—

Power supply terminal (+3.3V) (for analog system )

100

MONO/ST

I

REC MODE switch (S746) input terminal    “L”: MONO, “H”: STEREO

*1  Loading motor (M103) control

Mode  

  Terminal

LDIN (pin &•)

“L”

“H”

“L”

“H”

LDOUT (pin &ª)

“H”

“L”

“L”

“H”

LOADING

EJECT

BRAKE

RUN IDLE