DOWNLOAD Sony MDS-JA20ES Service Manual ↓ Size: 6.07 MB | Pages: 88 in PDF or view online for FREE

– 83 –

Pin No.

Pin Name

I/O

Function

40

AVDDL

—

Power supply terminal (+5V) (for L-ch side D/A converter section, analog system)                          
Not used (open)

41

L1

O

L-ch PLM signal 1 output terminal    Not used (open)

42

VDD2

—

Power supply terminal (+5V) (for L-ch side D/A converter section, digital system)                          
Not used (open)

43, 44

VDD1

—

Power supply terminal (+5V) (for A/D converter section, digital system)

45

VSS1

—

Ground terminal (for A/D converter section, digital system)

46

TEST2

I

Input terminal for the test (fixed at “L”)

47

TEST3

I

Input terminal for the test (fixed at “L”)

48

VSS1

—

Ground terminal (for A/D converter section, digital system)

49

NU

—

Not used (open)

50

NU

—

Not used (open)

51

AVSS

—

Ground terminal (for A/D converter section, analog system)

52

LVDD

—

Power supply terminal (+5V) (for A/D converter section, buffer system)

53

LVSS

—

Ground terminal (for A/D converter section, buffer system)

54

REFO

O

Reference voltage (+3.3V) output terminal (for A/D converter section)

55

INLM

I

L-ch analog signal (+) input terminal

56

INLP

I

L-ch analog signal (–) input terminal

– 84 –

•

Pin No.

Pin Name

I/O

Function

1

JOG1

I

JOG dial pulse input from the rotary encoder (S713  

≠ AMS ±)

2

JOG0

I

JOG dial pulse input from the rotary encoder (S713  

≠ AMS ±)

3

C1

O

Monitor output terminal for the test    C1 error rate is output when test mode

4

ADER

O

Monitor output terminal for the test    ADER is output when test mode

5

SQSY

I

Subcode Q sync (SCOR) input from the CXD2654R (IC121)                                                            
“L” is input every 13.3 msec    Almost all, “H” is input

6

RMC

I

Remote control signal input from the remote control receiver (IC761)

7

AIN1

I

Sircs remote control signal input of the S-LINK CONTROL A1

8

BYTE

I

External data bus line byte selection signal input    “L”: 16 bit, “H”: 8 bit (fixed at “L”)

9

CNVSS

—

Ground terminal

10

XT-IN

I

Sub system clock input terminal (32.768 kHz)

11

XT-OUT

O

Sub system clock output terminal (32.768 kHz)

12

S.RST

I

System reset signal input from the LA5632 (IC700)    “L”: reset                                                        
For several hundreds msec. after the power supply rises, “L” is input, then it changes to “H”

13

XOUT

O

Main system clock output terminal (7 MHz)

14

GND

—

Ground terminal

15

XIN

I

Main system clock input terminal (7 MHz)

16

+3.3V

—

Power supply terminal (+3.3V)

17

NMI

I

Non-maskable interrupt input terminal (fixed at “H” in this set)

18

DQSY

I

Digital In U-bit CD format subcode Q sync (SCOR) input from the CXD2654R (IC121)                 
“L” is input every 13.3 msec    Almost all, “H” is input

19

P.DOWN

I

Power down detection signal input terminal    “L”: power down, normally: “H”

20

XINT

I

Interrupt status input from the CXD2654R (IC121)

21

DVOL1

I

JOG dial pulse input from the rotary encoder (S740  DIGITAL REC LEVEL)

22

DVOL0

I

JOG dial pulse input from the rotary encoder (S740  DIGITAL REC LEVEL)

23 to 30

NC

I

Not used (fixed at “L”)

31

SWDT

O

Writing data output to the CXD2654R (IC121) and D/A converter (IC200)

32

SRDT

I

Reading data input from the CXD2654R (IC121)

33

SCLK

O

Serial clock signal output to the CXD2654R (IC121) and D/A converter (IC200)

34

FLCS

O

Chip select signal output to the FL/LED driver (IC771)

35

FLDATA

O

Serial data output to the FL/LED driver (IC771)

36

NC

I

Not used (fixed at “L”)

37

FLCLK

O

Serial data transfer clock signal output to the FL/LED driver (IC771)

38 to 47

NC

I

Not used (fixed at “L”)

48

CSET0

I

Destination setting terminal (US, Canadian models: fixed at “L”, AEP, UK models: fixed at “H”)

49

CSET1

I

Destination setting terminal (US, Canadian models: fixed at “H”, AEP, UK models: fixed at “L”)

50

20/X720

I

Setting terminal of the loading control system select (fixed at “H” in this set)

51

NC

I

Not used (fixed at “L”)

52

MNT2 (XBUSY)

I

Busy signal input from the CXD2654R (IC121)

53

DIG-RST

O

Reset signal output to the CXD2654R (IC121) and BH6511FS (IC152)    “L”: reset

54

MNT1 (SHOCK)

I

Track jump detection signal input from the CXD2654R (IC121)

55

SENS

I

Internal status (SENSE) input from the CXD2654R (IC121)

56

LDON

O

Laser diode on/off control signal output to the automatic power control circuit    “H”: laser on

57

REFLECT

I

Detection input from the disc reflection rate detect switch (S102)                                                      
“L”: high reflection rate disc, “H”: low reflection rate disc

58

PROTECT

I

Rec-proof claw detect input from the protect detect switch (S102)    “H”: write protect

– 85 –

Pin No.

Pin Name

I/O

Function

59

WR-PWR

O

Laser power select signal output to the CXD2654R (IC121) and HF module switch circuit              
“H”: recording mode, “L”: playback mode

60

MNT3 (SLOCK)

I

Spindle servo lock status monitor signal input from the CXD2654R (IC121)

61

SDA

I/O

Two-way data bus with the EEPROM (IC171)

62

+3.3V

—

Power supply terminal (+3.3V)

63

NC

I

Not used (fixed at “L”)

64

GND

—

Ground terminal

65

SCTX

O

Recording data output enable signal output to the CXD2654R (IC121) and overwrite head              
driver (IC181)    Writing data transmission timing output (Also serves as the magnetic head on/off 
output)

66

SCL

O

Clock signal output to the EEPROM (IC171)

67

MNT0 (FOK)

I

Focus OK signal input from the CXD2654R (IC121)                                                                          
“H” is input when focus is on (“L”: NG)

68

LIMIT-IN

I

Detection input from the sled limit-in detect switch (S101)                                                                
The optical pick-up is inner position when “L”

Laser modulation select signal output to the HF module switch circuit

Playback power: “H”, Stop: “L”,

Recording power:

69

MOD

O

70

XLATCH

O

Serial data latch pulse signal output to the CXD2654R (IC121)

71

REC/PB

I

Not used (fixed at “L”)

72

TECONT

I

Not used (fixed at “L”)

73

XTSL

I

Not used (fixed at “L”)

74

OPEN

I

Detection input from the tray open detect switch (S10)    “L”: tray open

75

PLAY1

I

Detection input from the disc chucking-in detect switch (S11)     “L” active

76

REC

I

Detection input from the recording position detect switch (S12)    “L” active

77

PLAY2

I

Detection input from the play position detect switch (S13)    “L” active

78

LDIN

O

Motor control signal output to the loading motor driver (IC400)    “L” active    *1

79

LDOUT

O

Motor control signal output to the loading motor driver (IC400)    “L” active    *1

80

LD-LOW

O

Loading motor drive voltage control signal output for the loading motor driver (IC400)                   
“H” active

81

NC

I

Not used (fixed at “L”)

82

A1OUT

O

Sircs remote control signal output of the S-LINK CONTROL A1

83

MUTE

O

Audio line muting on/off control signal output terminal    “L”: line muting on

84

STB

O

Strobe signal output to the power supply circuit    “H”: power on, “L”: standby mode

2 sec

0.5 sec

*1  Loading motor (M10) control

Mode  

  Terminal

LDIN (pin &•)

“L”

“H”

“L”

“H”

LDOUT (pin &ª)

“H”

“L”

“L”

“H”

LOADING

EJECT

BRAKE

RUN IDLE

– 86 –

Pin No.

Pin Name

I/O

Function

85

COAX/XOPT

O

Optical in 1/2 or coaxial in selection signal output to the digital input selector (IC300)                     
“L”: OPT 1/2, “H”: COAXIAL

86

OPT2/XOPT1

O

Optical in 1 or optical in 2 selection signal output to the digital input selector (IC300)                     
“L”: OPT 1, “H”: OPT 2

87

DALATCH

O

Serial data latch pulse signal output to the D/A converter (IC200)

88

DARST

O

Reset signal output to the A/D converter (IC100) and D/A converter (IC200)    “L”: reset

89

LED0

O

LED drive signal output of the 

P (PAUSE) LED (D754)    “L”: LED on

90

LED1

O

LED drive signal output of the 

r REC LED (D755)    “L”: LED on

91

TIMER

I

TIMER switch (S751) input terminal (A/D input)                                                                               
“L”: PLAY, “H”: REC (OFF: center voltage)

92

SOURCE

I

INPUT switch (S741) input terminal (A/D input)

93

KEY3

I

Key input terminal (A/D input)    S731 to S734 (TIME, FADER, FILTER, MEGA CONTROL 
keys input)

94

KEY2

I

Key input terminal (A/D input)    S722 to S726 (PLAY/MODE, REPEAT, SCROLL/CLOCK 
SET, DISPLAY/CHAR, I/

u keys input)

95

KEY1

I

Key input terminal (A/D input)    S711 to S714  and S716 (MENU/NO, YES, PUSH ENTER, 
CLEAR, 

§ OPEN/CLOSE keys input)

96

AVSS

—

Ground terminal

97

KEY0

I

Key input terminal (A/D input)    S701 to S706 (

r REC, p, ), 0, P, ( keys input)

98

VREF

I

Reference voltage (+3.3V) input terminal (for A/D converter)

99

+3.3V

—

Power supply terminal (+3.3V) (for analog system )

100

MONO/ST

I

Recording mode switch input terminal    “L”: mono, “H”: stereo    Not used (fixed at “H”)