Sony ICF-CDK70 Service Manual ▷ View online
ICF-CDK70
9
3-7. OPTICAL PICK-UP BLOCK (KSM-213CCP)
two floating screws (PTPWHM 2.6)
two floating screws (PTPWHM 2.6)
two coil springs (insulator)
two insulators
two coil springs (insulator)
two insulators
Remove soldering from
the four points.
the four points.
flexible flat cable (16 core)
(CNP701)
(CNP701)
R CD board
RB optical pick-up block
(KSM-213CCP)
(KSM-213CCP)
mechanism deck
(back side)
(back side)
screw
(BVTT2
(BVTT2
s 6)
ICF-CDK70
10
3-8. HOW TO PULL OUT TRAY
3-9. BELT
(DLM3A)
"
optical pick-up block
Note:
When the optical pick-up block in which
the optical pick-up block is chucking and
which cannot draw out TRAY is chucking,
please draw out TRAY after removing an
optical pick-up block.
gear
Pull out the tray.
A gear " portion can be pushed to the limit of
the direction of an arrow.
cover
belt (DLM3A)
belt (DLM3A)
two screws
two screws
ICF-CDK70
11
SECTION 4
TEST MODE
CD SHIP MODE
Function to put tray of disc 1 into state of chuck for transportation
is installed in this set.
Procedure:
1. Turn the power on, and put it into the state that there is no CD
Function to put tray of disc 1 into state of chuck for transportation
is installed in this set.
Procedure:
1. Turn the power on, and put it into the state that there is no CD
in the disc tray.
2. Press two keys of the [
x
] and [1] simultaneously.
3. The message “0000” is displayed and the tray is chucked.
CDM RESET
Mode to initialize CD mechanism deck.
Procedure:
1. Turn the power on.
2. Press
Mode to initialize CD mechanism deck.
Procedure:
1. Turn the power on.
2. Press
the
[
x
] key for fi ve seconds, and CD mechanism deck is
initialized.
PANEL TEST
Mode that test LCD, and display the version and destination.
Procedure:
1. Turn the power on.
2. Press three keys of the [
Mode that test LCD, and display the version and destination.
Procedure:
1. Turn the power on.
2. Press three keys of the [
x
], [2] and [
.
] simultaneously.
Then all segments of liquid crystal display are turned on.
3. Press the [1] key, the destination and version are displayed.
4. Press the [2] key, the released date of the micro computer is
4. Press the [2] key, the released date of the micro computer is
displayed.
5. To exit from this mode, perform the step 2.
ICF-CDK70
12
NORMAL MODE
INITIAL
(TEST MODE IN)
(TEST MODE IN)
88
81
Y + 3 +
TUNING MODE key
TUNING MODE key
STOP 1 MODE
Whenever the
MODE key is
pressed, each
adjustment value
is displayed.
MODE key is
pressed, each
adjustment value
is displayed.
82
Y key
Y key
Y key
Y
key
Y
key
STOP 2 MODE
82
COMMAND
FORWARDING
MODE
FORWARDING
MODE
F-
FOCUS 2 MODE
FOCUS 1
MODE
MODE
F-
P-
ALL SERVO
ON MODE
ON MODE
P-
(61
TG UP MODE
A-
AUTO
ADJUSTMENT
MODE
ADJUSTMENT
MODE
Auto adjustment: NG
Auto adjustment: OK
V key
V key
V
key
V key
V
key
V key
V key
V key
V
key
V
key
V
key
2 key
2 key
2 key
Y
key
3 key
Y
key
MODE key
82
ALL SERVO
ON MODE
(IN COMMAND
FORWARDING
MODE)
ON MODE
(IN COMMAND
FORWARDING
MODE)
3 key
82
TG UP MODE
(IN COMMAND
FORWARDING
MODE)
(IN COMMAND
FORWARDING
MODE)
2 key
MODE key
MODE key
Whenever the
MODE key is
pressed, each
adjustment value
is displayed.
MODE key is
pressed, each
adjustment value
is displayed.
MODE key
Ykey
MODE key
Ykey
Ykey
MODE key
Whenever the
MODE key is
pressed, each
adjustment value
is displayed.
MODE key is
pressed, each
adjustment value
is displayed.
Content of adjustment value
92xx
92xx
: RF offset
94xx :
Tracking
balance
95xx :
Tracking
in
96xx :
Focus
balance
97xx :
Focus
in
EAxx
: All in setting
98xx
: VC offset
99xx
: Sled offset
9Axx
: Focus offset
9bxx :
Tracking
offset
9Cxx
: AC amplifier offset
9dxx
: BD amplifier offset
9Exx
: E amplifier offset
9Fxx
: F amplifier offset
61xx
: APC reference level setting
Note: 61, 92 to 9F, EA : register address of DSP
xx
xx
: adjustment value (Hexadecimal number)
MODE key
Fig. 1 Method of operating CD test mode
CD TEST MODE
Procedure:
1. Turn the power on.
2. Press three keys of the [
Procedure:
1. Turn the power on.
2. Press three keys of the [
x
], [3] and [TUNING MODE] simul-
taneously.
3. When the CD test mode is activated, “88” is displayed.
4. Insert the CD to the tray of disc 1, and press the [
4. Insert the CD to the tray of disc 1, and press the [
u
] key to
the playback.
5. Operate it referring to the fi gure below.
Click on the first or last page to see other ICF-CDK70 service manuals if exist.