Sony ICF-CD830 / ICF-CD830L Service Manual ▷ View online
3
ICF-CD830/CD830L
The laser diode in the optical pick-up block may suffer electrostatic
break-down because of the potential difference generated by the
charged electrostatic load, etc. on clothing and the human body.
During repair, pay attention to electrostatic break-down and also
use the procedure in the printed matter which is included in the
repair parts.
The flexible board is easily damaged and should be handled with
care.
break-down because of the potential difference generated by the
charged electrostatic load, etc. on clothing and the human body.
During repair, pay attention to electrostatic break-down and also
use the procedure in the printed matter which is included in the
repair parts.
The flexible board is easily damaged and should be handled with
care.
NOTES ON LASER DIODE EMISSION CHECK
The laser beam on this model is concentrated so as to be focused on
the disc reflective surface by the objective lens in the optical pick-
up block. Therefore, when checking the laser diode emission,
observe from more than 30 cm away from the objective lens.
the disc reflective surface by the objective lens in the optical pick-
up block. Therefore, when checking the laser diode emission,
observe from more than 30 cm away from the objective lens.
NOTES ON HANDLING THE OPTICAL PICK-UP
BLOCK OR BASE UNIT
BLOCK OR BASE UNIT
CAUTION
Use of controls or adjustments or performance of procedures
other than those specified herein may result in hazardous
radiation exposure.
other than those specified herein may result in hazardous
radiation exposure.
This Compact Disc player is classified as a CLASS 1
LASER product.
The CLASS 1 LASER PRODUCT label is located on the
bottom exterior.
LASER product.
The CLASS 1 LASER PRODUCT label is located on the
bottom exterior.
CHUCK PLATE JIG ON REPAIRING
On repairing CD section, playing a disc without the CD lid, use
Chuck Plate Jig.
• Code number of Chuck Plate Jig: X-4918-255-1
Chuck Plate Jig.
• Code number of Chuck Plate Jig: X-4918-255-1
LASER DIODE AND FOCUS SEARCH
OPERATION CHECK
OPERATION CHECK
1. Open the CD lid.
2. Turn on S401 as following figure.
3. Confirm that the laser diode emission while observing the
2. Turn on S401 as following figure.
3. Confirm that the laser diode emission while observing the
objecting lens. When there is no emission, Auto Power Control
circuit or Optical Pick-up is broken.
Objective lens moves up and down once for the focus search.
circuit or Optical Pick-up is broken.
Objective lens moves up and down once for the focus search.
Insert a precision
screwdriver and
push S401
screwdriver and
push S401
laser diode
emission
emission
4
ICF-CD830/CD830L
SECTION 1
GENERAL
This section is extracted from
instruction manual.
instruction manual.
Setting the Clock
and Date
and Date
1
Plug in the clock radio.
The display will flash “AM 12:00” or “0:00”.
2
Press CLOCK for a few seconds.
You will hear a beep and the year will start to
flash in the display.
flash in the display.
3
Press TIME SET + or – until the correct
year appears in the display.
year appears in the display.
4
Press CLOCK once.
5
Repeat steps 3 and 4 to set the month,
day, hour, and minute.
day, hour, and minute.
After setting the minute, press CLOCK to start
the counting of the seconds, and you will
hear two short beeps.
the counting of the seconds, and you will
hear two short beeps.
• To display the year and date, press SNOOZE/
DATE/SLEEP OFF once for the date, and within
2 seconds press it again for the year. The
display shows the date or year for a few
seconds and then changes back to the current
time.
2 seconds press it again for the year. The
display shows the date or year for a few
seconds and then changes back to the current
time.
• To set the current time rapidly, hold down
TIME SET + or –.
• The clock system varies depending on the
model you own.
12-hour system: “AM 12:00” = midnight
24-hour system: “0:00” = midnight
12-hour system: “AM 12:00” = midnight
24-hour system: “0:00” = midnight
• In step 5, when you press CLOCK after the
minute setting to activate the clock, the seconds
start counting from zero.
start counting from zero.
To change the display to the
daylight saving time (summer time)
indication
daylight saving time (summer time)
indication
Press D.S.T./SUMMER T.
“
“
” is displayed and the time indication
changes to summer time.
To deactivate the summer time function, press
D.S.T./SUMMER T. again.
To deactivate the summer time function, press
D.S.T./SUMMER T. again.
FM wire antenna
Antenne fil FM
Antenne fil FM
AC power cord
Cordon d’alimentation
secteur
Cordon d’alimentation
secteur
ICF-CD830
ICF-CD830L
VOLUME
5
ICF-CD830/CD830L
2-1. UPPER CASE
Note:
Follow the disassembly procedure in the numerical order given.
SECTION 2
DISASSEMBLY
• The equipment can be removed using the following procedure.
2-2. KEY BOARD
4
Lid, CD
2
Panel (SP)
5
Screw (+P3
×
14)
3
Five screws (+P3
×
14)
7
Upper case
6
Connector
(CN371)
Pointer
1
Eight claws
Precaution during installation
When installing the upper case to the main section,
move the pointer to the left-most end as shown.
move the pointer to the left-most end as shown.
3
Key board
2
Hook
1
Five screws
(+P3
×
10)
4
Wire
Transformer board
Key board
Upper case
Set
Main chassis
Optical pick-up block (KSM-213CDM)
Ver 1.1 2001.08
6
ICF-CD830/CD830L
2-3. TRANSFORMER BOARD
2-4. MAIN CHASSIS
2
Two screws
(+P3
×
10)
1
Connector
(CN901)
3
Bracket (Trans)
4
Transformer board
Transformer board
Power cord
2-5. OPTICAL PICK-UP BLOCK (KSM-213CDM)
1
Two screws
(+P3
×
10)
2
Six screws
(+P3
×
10)
4
Main chassis
3
Connector
(CN901)
3
Optical pick-up block
(KSM-213CDM)
1
Two screws
(2.6
×
10)
2
Two screws
(2.6
×
10)