Sony ICF-CD73W Service Manual ▷ View online
ICF-CD73W
5
– CABINET (FRONT) SECTION, SPEAKER SECTION –
– SECTIONAL VIEW –
– SECTIONAL VIEW –
– SECTIONAL VIEW –
– SECTIONAL VIEW –
– CABINET UPPER: INSIDE –
– CABINET (FRONT) ASSY SECTION, CABINET (UPPER) ASSY SECTION –
Apply so as to plug three holes.
adhesive agent
cabinet (front)
adhesive agent
cabinet (upper)
ditch
adhesive agent
adhesive agent
adhesive agent
ditch
ditch
ditch
Apply to the peripheries of the speakers.
Apply so as to be flush with this surface.
Apply so as to be flush with this surface.
Apply to the entire circumference
along the groove.
along the groove.
Apply so as to be flush with this surface.
Apply until the FM wire antenna is completely
hidden in the hole for storing the FM antenna.
hidden in the hole for storing the FM antenna.
FM wire antenna
cabinet (front)
cabinet (front) assy section
cabinet (front)
cabinet (front)
cabinet (front)
cabinet (front) assy section
cabinet (upper) assy section
Apply to the top surfaces of the ribs.
cabinet (upper) assy section
speaker
speaker
Note: Attach the cabinet (upper) assy section to the cabinet (front) assy section, and then apply an adhesive agent.
ICF-CD73W
6
SECTION 2
GENERAL
This section is extracted
from instruction manual.
from instruction manual.
5
4
3
2
AUTO
OFF
VOLUME
TUNE/TIME SET
TIMER SET
MAX
MIN
TIMER
SET
ON/OFF
MODE
PRESET TUNING/PRESET TIMER
SELECT/
PRESET
CLOCK
1
RADIO
CD
SHUFFLE
REP1
MHz
kHz
AUTO OFF
TIMER
PRESET
TRACK
WEATHER
FM12PM
AM
ALL
RADIO
ON
BAND
OFF
CD
FM wire antenna
Setting the Clock
The display will flash “AM12:00” when the
batteries are installed or the AC power adaptor
is plugged in for the first time.
batteries are installed or the AC power adaptor
is plugged in for the first time.
1
Hold down CLOCK for more than
2 seconds.
2 seconds.
The beep sounds and the hour flashes in the
display.
display.
2
Rotate in either +/– direction the TUNE/
TIME SET/TIMER SET dial until the
correct hour appears in the display.
TIME SET/TIMER SET dial until the
correct hour appears in the display.
RADIO
CD
SHUFFLE
REP1
MHz
kHz
AUTO OFF
TIMER
PRESET
TRACK
WEATHER
TV
FM12PM
AM
ALL
Each rotation of the dial changes the digit(s)
by one.
When you hold the dial, the digit(s) change
rapidly.
by one.
When you hold the dial, the digit(s) change
rapidly.
3
Press CLOCK.
The beep sounds and the minute starts to
flash. Repeat step 2 to set the minute. After
setting the minute, press CLOCK again. The
two beeps sound and the clock starts from
0 seconds.
flash. Repeat step 2 to set the minute. After
setting the minute, press CLOCK again. The
two beeps sound and the clock starts from
0 seconds.
RADIO
CD
SHUFFLE
REP1
MHz
kHz
AUTO OFF
TIMER
PRESET
TRACK
WEATHER
TV
FM12PM
AM
ALL
12-hour system: “AM 12:00” = midnight
“PM 12:00” = noon
Notes
• You can set the clock also during the radio
• You can set the clock also during the radio
reception/CD playback mode.
• To set the current time quickly, rotate and hold
in either +/– direction the TUNE/TIME SET/
TIMER SET dial.
TIMER SET dial.
• To set the current time exactly, follow step 2
and press CLOCK again with the time signal of
a radio station.
a radio station.
ICF-CD73W
7
SECTION 3
DISASSEMBLY
• This set can be disassembled in the order shown below.
3-1. DISASSEMBLY FLOW
Note:
Follow the disassembly procedure in the numerical order given.
3-2. CABINET (FRONT) BLOCK
3-2. CABINET (FRONT) BLOCK
(Page
(Page
7)
3-3. CABINET (UPPER) BLOCK
(Page
(Page
8)
3-7. SPEAKER (5 cm) (SP101)/(SP201)
(Page
(Page
10)
3-6. OPTICAL PICK-UP BLOCK
(KSM-900AAA)
(Page
(KSM-900AAA)
(Page
9)
3-5. LCD BOARD
(Page
(Page
9)
SET
3-4. CHASSIS (MAIN) BLOCK
(Page
(Page
8)
two screws
(BVTP2.6
(BVTP2.6
× 10)
two screws
(BVTP2.6
(BVTP2.6
× 10)
screw
(BTP2.6
(BTP2.6
× 8)
SW board block
cabinet (front) block
five screws
(BVTP2.6
(BVTP2.6
× 10)
Open the buckle
(battery case lid).
Open the
battery case lid.
flexible flat cable (20 core)
(CNP704)
(CNP704)
connector
(CNP302)
(CNP302)
ICF-CD73W
8
two screws
(BVTP2.6
(BVTP2.6
× 8)
two claws
cabinet (upper) block
connector
(CNP602)
(CNP602)
connector
(CNP601)
(CNP601)
flexible flat cable (13 core)
(CNP702)
(CNP702)
connector
(CNP303)
(CNP303)
connector
(CNP304)
(CNP304)
two screws
(BTP2.6
(BTP2.6
× 8)
two screws
(BTP2.6
(BTP2.6
× 8)
three screws
(BTP2.6
(BTP2.6
× 8)
chassis (main) block
Remove the solder of FM lead
wire antenna (ANT1).
R cabinet (front) block
CD board
3-3. CABINET (UPPER) BLOCK
3-4. CHASSIS (MAIN) BLOCK
Click on the first or last page to see other ICF-CD73W service manuals if exist.