Sony ICF-CD523 Service Manual ▷ View online
ICF-CD523
9
3-8. LOADING BOARD
1
belt
3
claw
3
claw
4
LOADING board
2
two screws
(M2
(M2
×
3)
3
boss
4
base unit assy
2
boss
2
boss
1
two screws
(PWH2.6
(PWH2.6
×
10)
3-9. BASE UNIT ASSY
ICF-CD523
10
3-11. OPTICAL PICK-UP
(KSS-213C)
3
sled shaft
2
1
gear (A)
4
optical pick-up
(KSS-213C)
(KSS-213C)
2
arm
4
vibration proof rubber
(red)
(red)
4
vibration proof rubber
(red)
(red)
3
vibration proof rubber
(green)
(green)
3
vibration proof rubber
(green)
(green)
1
two screws
(PWH2.6
(PWH2.6
×
10)
5
optical pick-up block
(KSM-213CCP)
(KSM-213CCP)
3-10. OPTICAL PICK-UP BLOCK
(KSM-213CCP)
11
ICF-CD523
5. The optical pick-up will move inward if the . button is
pressed, or outward if the > button is pressed.
6. Press the [BAND] button, and the spindle/tracking servo will
turn on, and if the data are read in, the mute turns off.
7. With the spindle/tracking servo turned on, pressing respective
buttons causes the operation to be performed as follows.
Name of Buttons
Operation
[1]
1 track jump setting
[2]
10 track jump setting
[3]
100 track jump setting
[4]
Tracking gain up
[5]
Returns to auto adjustment mode
[BAND]
Rough servo function turns on
8. After setting, press the . or > button to start the track
jump.
9. When the CD test-1 mode becomes active, press the Z button
and the disc table will open.
10. With the rough servo or spindle/tracking servo turned on, press
the x button and the CD will stop, and then press the u
button and the operation will repeat, starting from focus search.
button and the operation will repeat, starting from focus search.
11. With the rough servo or spindle/tracking servo turned on, press
the u button and the optical pick-up will jump to the second
music and the set will release from the CD test-1 mode.
music and the set will release from the CD test-1 mode.
SECTION 4
TEST MODE
4-1. LCD TEST MODE
Setting the Test Mode
Turn the power on while pressing u , > and [ALARM ON/
OFF] buttons simultaneously.
OFF] buttons simultaneously.
Operation of Test Mode
1. When LCD test mode becomes active, the microcomputer
version number is displayed on the LCD.
2. Press the Z button, and all segments of LCD will turn on.
LCD display
3. Press each button, and the corresponding segment will turn
off. Relation between buttons and corresponding segments is
as follows.
as follows.
Name of Buttons
Segment (Display)
Z
TRACK
u
CD N
[BAND]
RADIO, FM1, FM2,.(POINT)
x
.
>
[CD PLAY MODE]
REP 1, ALL, SHUFFLE
[CLOCK]
AM, PM, :(COLON)
[D.S.T.]
[1]
[2]
[3]
[4]
[5]
[ALARM]
,
[ALARM ON/OFF]
Note:
The buttons may be pressed in random order.
4. Finally, press the [ALARM ON/OFF] button to release from the
LCD test mode. However, the LCD test mode does not release
if even one button has not been pressed yet whatever you
pressed the [ALARM ON/OFF] button.
if even one button has not been pressed yet whatever you
pressed the [ALARM ON/OFF] button.
4-2. CD TEST-1 (AUTO) MODE
Setting the Test Mode
Short the solder bridge of BP404 on the MAIN board (connect
IC401tl pin and ground) and turn the power on. (See page 12)
IC401tl pin and ground) and turn the power on. (See page 12)
Operation of Test Mode
1. When the CD test-1 mode becomes active, the disc table opens.
2. Insert the CD test disc PATD-012. (Parts No. 4-225-203-01)
3. Press the u button, and the focus search will repeat until
2. Insert the CD test disc PATD-012. (Parts No. 4-225-203-01)
3. Press the u button, and the focus search will repeat until
the focus is OK.
4. When the focus is OK, auto adjustment is executed and at the
completion, the rough servo function turns on and the adjusted
value is displayed on the LCD.
value is displayed on the LCD.
LCD display
F-E balance
adjusted value
Tracking gain
adjusted value
Focus bias
adjusted value
12
ICF-CD523
4-3. CD TEST-2 (MANUAL) MODE
Setting the Test Mode
• Short the solder bridge of BP403 on the MAIN board (connect
IC401 tk pin and ground) and turn the power on.
Operation of Test Mode
1. Insert the CD test disc PATD-012. (Parts No. 4-225-203-01)
2. Press the u button, and the focus search will repeat until
2. Press the u button, and the focus search will repeat until
the focus is OK.
3. When the focus is OK, the rough servo function turns on.
4. Press the [BAND] button, and the spindle/tracking servo will
4. Press the [BAND] button, and the spindle/tracking servo will
turn on, and if the data are read in, the mute turns off. Press
the [BAND] button again, and the rough servo will turn on.
the [BAND] button again, and the rough servo will turn on.
5. With the rough servo or spindle/tracking servo turned on the
optical pick-up will move inward if the . button is pressed,
or outward if the > button is pressed.
or outward if the > button is pressed.
6. With the rough servo or spindle/tracking servo turned on, press
the x button and the CD will stop, and then press the u
button and the operation will repeat, starting from focus search.
button and the operation will repeat, starting from focus search.
7. With the rough servo or spindle/tracking servo turned on, press
the u button and the optical pick-up will jump to the second
music and the set will release from the CD test-2 mode.
music and the set will release from the CD test-2 mode.
Connecting Location:
BP403
– MAIN Board (Conductor Side) –
BP404
Short: CD Test-1 Mode
Open: Normal Mode
Open: Normal Mode
Short: CD Test-2 Mode
Open: Normal Mode
Open: Normal Mode
Click on the first or last page to see other ICF-CD523 service manuals if exist.