Sony ICD-UX543 / ICD-UX543F / ICD-UX544F Service Manual ▷ View online
ICD-UX543/UX543F/UX544F
9
2-6. BATTERY SUB ASSY (BAT301)
2-5. ELECTRET CAP MICROPHONE (L/R-ch) (MIC301, MIC302)
– Rear bottom view –
3 electret cap microphone
(L-ch)
(MIC301)
electret cap microphone
3 electret cap microphone
(R-ch)
(MIC302)
2 cushion (MIC)
2 cushion (MIC)
cushion (MIC)
electret cap
microphone
block (L-ch)
microphone
block (L-ch)
electret cap
microphone
block (R-ch)
microphone
block (R-ch)
Microphone wire setting
Cushion (MIC) setting
1 Remove the microphone block (L-ch)
in the direction of an arrow.
1 Remove the microphone block (R-ch)
in the direction of an arrow.
Note: Check that the cushion (MIC) is not turned up.
Pass through ditches.
– Rear bottom view –
2 Remove the battery sub assy (BAT301)
in the direction of an arrow.
1 Peel off the adhesive sheet.
battery sub assy (BAT301)
speaker sub assy (SP1)
Pass through between the bosses.
battery wire
[red]
[red]
%atter\ wire VettiQJ
3 battery sub assy (BAT301)
Note: When removed the battery from the
adhesive sheet, not reuse the battery.
ICD-UX543/UX543F/UX544F
10
2-7. SPRING LINK (USB)
2-8. WINDOW (EL) SUB ASSY
1 Slide the knob (USB) in the
direction of an arrow.
1 Slide the knob (USB)
in the direction of an
arrow.
4 Slide the knob (USB)
in the direction of an
arrow.
2 claw
3 hole
4 spring link (USB)
+RZWRLQVWDOOWKHVSULQJOLQN86%
Note: Follow the assembly procedure in the numerical order given.
2 Insert the spring link
(USB) to the hole.
3 Hook the spring link
(USB) to the claw.
– Front bottom view –
2 claw
3 window (EL) sub assy
1 Peel off the adhesive sheet (window)
Note: When removing the chassis unit from the case (front) block,
exchange the window (EL) sub assy at same time.
ICD-UX543/UX543F/UX544F
11
2-9. CASE (FRONT) BLOCK
– Rear bottom view –
1 screw (M1.4)
3 Remove the chassis unit in
the direction of an arrow.
chassis unit
4 rib
5 case (front) block
4 rib
2 screw (B1.4)
86% IOe[ibOe boarG VettiQJ
Wrap the USB flexible board.
chassis unit
knob (USB)
+ow to iQVtaOO tKe FaVe IroQt bOoFN
Note 1: When removing the chassis unit from the panel (front) block,
exchange the window (EL) sub assy at same time.
Note 2: When installing the case (front) block,
align two bosses of knob (USB) and
two hole of chassis unit.
ICD-UX543/UX543F/UX544F
12
2-10. SPEAKER SUB ASSY (SP1)
– Rear bottom view –
2 Remove the speaker sub assy (SP1)
in the direction of an arrow.
hole
1 Peel off the adhesive sheet (SP).
3 speaker sub assy (SP1)
Note: When installing the speaker sub assy (SP1),
align two holes of the speaker sub assy (SP1)
and the two holes of the chassis assy.
hole
hole
hole
2-11. USB SLIDE BLOCK
1 claw
1 claw
3 two claws
3 two claws
2 Remove the USB slide block
in the direction of an arrow.
4 USB slide block
Click on the first or last page to see other ICD-UX543 / ICD-UX543F / ICD-UX544F service manuals if exist.