DOWNLOAD Sony ICD-SX35 Service Manual ↓ Size: 1.76 MB | Pages: 36 in PDF or view online for FREE

AEP Model

UK Model

E Model

Chinese Model

Tourist Model

2005J16-1
© 2005.10

Recording media

Built-in flash memory 64 MB Stereo/
Monaural recording

Recording time

Frequency range

• ST: 60 Hz - 13,500 Hz
• STLP: 60 Hz - 6,900 Hz
• SP: 60 Hz - 7,000 Hz
• LP: 80 Hz - 3,500 Hz

• ST: 2 hr. 50 min. 
• STLP: 5 hr. 35 min. 
• SP: 8 hr. 50 min. 
• LP: 23 hr. 40 min.

Speaker

Approx. 16 mm (

21

/

32

 in.) dia.

Power output

150 mW

Input/Output

• Microphone jack (minijack, stereo)

– input for plug in power, minimum input level
   0.6 mV, 3 kilohms or lower impedance microphone

• Headphones jack (minijack, stereo)

– output for 8 - 300 ohms headphones

• USB connector

• DC IN 3V jack

Playback speed control

+100% to -50%  (DPC)

Power requirements

Two LR03 (size AAA) alkaline batteries: 3 V DC

Dimensions (w/h/d) (not incl. projecting parts and controls)

28.0 

×

 120.0 

×

 13.8 mm (1 

1

/

8

   4 

3

/

4

 

×

×

9

/

16 

in.)

Mass (incl. batteries)

64 g (2.26 oz)

Supplied accessories

Stereo headphones 

×

 1

USB connecting cable 

×

 1

Application Software (CD-ROM) 

×

 1

Operating instruction 

×

 1

Design and specifications are subject to change without notice.

2

...................................................................

3

2-1.

Disassembly Flow ...........................................................

4

2-2.

Cover (jack) .....................................................................

4

2-3.

Case Block Assy ..............................................................

5

2-4.

AUDIO Board, Microphone Unit (MIC2/3) ....................

5

2-5.

Ornament Belt, SW Board ...............................................

6

2-6.

Cover (chassis) Block Assy .............................................

6

2-7.

MAIN Board, Liquid Crystal Display Panel ...................

7

...............................................................

8

4-1.

Block Diagrams  – MAIN Section-1 – ............................ 12

4-2.

Block Diagrams  – MAIN Section-2 – ............................ 13

4-3.

Block Diagrams  – PANEL Section – ............................. 14

4-4.

Printed Wiring Board  – MAIN Board – ......................... 15

4-5.

Schematic Diagram  – MAIN Board (1/2) – ................... 16

4-6.

Schematic Diagram  – MAIN Board (2/2) – ................... 17

4-7.

Printed Wiring Board  – AUDIO Board – ....................... 18

4-8.

Schematic Diagram  – AUDIO Board (1/2) – ................. 19

4-9.

Schematic Diagram  – AUDIO Board (2/2) – ................. 20

4-10. Printed Wiring Board  – SW Board – .............................. 21
4-11. Schematic Diagram  – SW Board – ................................. 22

5-1.

Case Block Assy .............................................................. 30

5-2.

Chassis Block Assy ......................................................... 31

.................................. 32

• Keep the temperature of the soldering iron around 270 °C

during repairing.

• Do not touch the soldering iron on the same conductor of the

circuit board (within 3 times).

• Be careful not to apply force on the conductor when soldering

or unsoldering.

• Never reuse a disconnected chip component.

• Notice that the minus side of a tantalum capacitor may be

damaged by heat.

✩ Replacement of IC6001 and  IC7003 used in this set requires

a special tool.

•

The voltage and waveform of CSP (chip size package) cannot
be measured, because its lead layout is different from that of
conventional IC.

•

Lead layouts

surface

Lead layout of

conventional IC

CSP (chip size package)

Boards requiring use of unleaded solder are printed with the lead-
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with

the lead free mark due to their particular size)

Unleaded solder has the following characteristics.

• Unleaded solder melts at a temperature about 40 °C higher

than ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350 

°C.

Caution: The printed pattern (copper foil) may peel away if

the heated tip is applied for too long, so be careful!

• Strong viscosity

Unleaded solder is more viscou-s (sticky, less prone to flow)
than ordinary solder so use caution not to let solder bridges
occur such as on IC pins, etc.

• Usable with ordinary solder

It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder. Operating instructiondd

3

This section is extracted
from instruction manual.

1 i

 (headphones) jack (17, 19)

2

Built-in microphone (11, 13)

3

DIRECTNL (directional)
switch (13)

4

VOICE UP (Digital Voice
Up) switch (29)

5

DPC ON/OFF switch  (30)

6

Display window (23)

7

ERASE button (36)

8

DIVIDE/

 (bookmark)

button (32, 39)

9

A-B 

 (repeat)/PRIORITY

button (33, 43)

0

OPR (operation) indicator
(11, 19)

Refer to the pages indicated in parentheses for details.

qa

zREC (record) /REC
PAUSE button (11, 34)

qs

xSTOP button (12, 20)

qd

Jog lever
FOLDER/MENU/
.(review/fast backward)/
> (cue/fast forward)/
x• B (play/stop•enter)

qf

VOL (volume) +/– buttons
(19)

qg

Base

qh

HOLD switch (28, 50)

qj

Speaker

qk

Battery compartment (6)

ql

Clip*

w; m

 (microphone) jack (16)

wa

USB connector (55)

ws

DC IN 3V jack (6)

wd

Slit for a handstrap

• To prevent the clip from

breaking, avoid hooking it on
thick fabric, such as a pocket
of a heavy coat.

• When bending down or

running with the unit clipped
on your pocket, be careful not
to drop the unit.

You need to set the clock to use the alarm function or record the date and
time.
Clock setting display appears when you insert batteries for the first time,
or when you insert batteries after the unit has been without batteries for a
certain period of time. In this case, proceed from step 4.

The menu mode will be displayed in
the  display window.

Press the jog lever up or down
(>/.) to select “SET DATE”.

Press the jog lever (x•B).

The date and time setting window is
displayed.  The year digits will flash.

1

Press the jog lever up or down
(>/.) to select the digits of
the year.

Press the center
(x•B).

Press up (>).

Press down (.).

2

Press the jog lever (x•B).
The month digits will flash.

3

Set the month and day in
sequence, then press the jog lever
(x•B).
The hour digits will flash.

1

Press the jog lever up or down
(>/.) to select the digits of
the hour.

2

Press the jog lever (x•B).
The minute digits will flash.

3

Set the minute.

4

Press the jog lever (x•B).

The menu mode will be

displayed again.

If you do not press the jog lever
(x•B) for more than one minute,
the clock setting mode is cancelled
and the window will return to
normal display.

The window will return to normal
display.

1 

If the unit is left unused for more than 3
seconds in the stop mode after the clock
is set, the display will show the current
time (page 26).

v

4

Follow the disassembly procedure in the numerical order given.

Disassemble the unit in the order as shown below.

2-3.CASE BLOCK ASSY

(Page 5)

2-4.AUDIO BOARD,

MICROPHONE UNIT(MIC2/3)

(Page 5)

2-5.ORNAMENT BELT,

SW BOARD

(Page 6)

2-6.COVER (CHASSIS)

BLOCK ASSY

(Page 6)

2-7.MAIN BOARD,

LIQUID CRYSTAL DISPLAY 

PANEL (Page 7)

2-2.COVER (JACK)

(Page 4)

SET

4

 screw

6

 screw

5

 cover (jack)

3

 lid (connecter)

2

 screw (M1.4)

1

 battery lid