DOWNLOAD Sony ICD-P28 Service Manual ↓ Size: 1.29 MB | Pages: 26 in PDF or view online for FREE

9

3. Sleep test
• Pressing the  x•B  key causes the set to enter the sleep state.
• Press any keys to exit the sleep state.

4. Beep test
• Beep sound of 1.3 kHz or 2 kHz is output.

5. RTC test
• Perform the connection test of the RTC, EEPROM.

(1) RTC EEPROM test

This test checks that any data is written and read to and from
specific registers (verify check) and that data is cleared.

(2) RTC clock function test

This test checks that the time is updated at intervals of 1 second
in the micro processor by the RTC.
• It determines whether a test result is OK or NG.

If NG, it indicates that either device of RTC or EEPROM was
found to be NG.
(All OKs: RTC OK/RTC NG: RTC BAD/EEPROM NG: EEP
BAD)

6. Key entry test
• When the any key is pressed, the entry key and the A/D

converted value (hexadecimal) of the two channel keys are
displayed.
KEY IN0 is displayed on the upper side and KEY IN1 on the
lower side.

• When the  STOP  key is pressed, the A/D value of the key is

displayed while the key is depressed. When the key is released,
the screen returns to the test menu.

7. Battery remaining power test
• The detected A/D value (hexadecimal) of the battery remaining

power is displayed.

8. LED test
• LED ( OPR : orange) are all turned on.

SLEEP

SOON

x 

• B

HOLD

SLEEP

with
off

any keys

BEEP

1.3k

(SET)

.  

/  >

x 

• B

x 

• B

(SELECT)

STOP

2.0k

•

•

•

•

•

•

1.3k

1.3k

2.0k

STOP

STOP

ON

ON

RTC

RTC

ON

x 

• B

STOP

KEY

KEY,OFF

OFF

x 

• B

STOP

BATT

BATT

AA

x 

• B

STOP

u

LED

LED

ON

x 

• B

STOP

10

9. USB test
• When the menu starts the USB self-check, either presence or

absence of the Vbus is judged.
(Vbus is present: “VBUS: ON”, Vbus is absent: “VBUS: OFF”)

• The USB driver always works regardless of presence or absence

of the USB signal only when Vbus is available during the USB
test. At this time, turning on  HOLD  causes the set to move to
the suspend state. Turning off the Vbus causes the set to return
to the test menu.
When Vbus is supplied with the menu displayed, the key will be
inoperative. Be sure to press  x•B  key before supplying.

10. Key durability test
• Input of  x•B  key causes the counter to be “- - - - - -”, entering

the test waiting mode. Input of  x•B  key causes the counter to
be “000000”, entering the key durability test mode.
In this mode, all key inputs and ON and OFF operations of the
slide switch are counted with a count display. Turn the power
off in order to exit this mode.

11. Menu reset
• Pressing the  x•B    key causes the set to enter the menu

initialization standby state.

• Once all the keys below are input in this condition, the EEPROM

will be initialized (The settings in the menu and the user name
will be defaulted.).
At the same time, the WakeUp signal is checked, too.

• Check keys (in any order of their inputs)

FOLDER  ,  DIVIDE  ,  DISPLAY  ,  MENU  ,  MIC SENS  ,
ERASE  ,  STOP  ,  REC/STOP  ,  PAUSE  ,
PLAY/STOP (ENTER)  ,  >  ,  .  ,  HOLD  on,
HOLD  off

(All is normally ended: –ALLOK–/NG in initialization write
to EEPROM: INIT. NG)

• Turn the power off in order to exit this mode.

x 

• B

STOP

HOLD  ON

USB

VBUS

VBUS on

Suspend mode

Cut VBUS

Cut VBUS

OFF

VBUS

ON

LINK

PC

x 

• B

STOP

COUNT

KEY

- - - - - -  

KEY

x 

• B

00  00  00

KEY

KEY

Key endurance
test mode

any keys or
slid switchs on/off

00  00  01

x 

• B

STOP

PUSH

After input all keys

Case of initial setting
and reset operated
normal end.

KEY

MENU

RST

INIT (Blink)

ALL

Ok

11

Pin No.

Pin Name

I/O

Pin Description

1

DSPSCK

O

Serial clock signal output to the DSP IC (IC101)

2

FLMCLE

O

Command latch enable signal output to the flash memory IC (IC701)

3 to 10

DATA0 to DATA7

I/O

Data input/output with the flash memory IC (IC701) and USB controller IC (IC8101)

11

XFLMCS0

O

Chip enable signal output to the flash memory IC (IC701)

12

DSPSYSCK

O

System clock control signal output for DSP (IC101)

13

X0A32K

I

32 kHz oscillator pin (32 kHz signal input) (IC703)

14

X1A32K

—

32 kHz oscillator pin

15

VCC3BCK

—

Power supply pin for internal logic back up

16

VSS

—

Ground pin

17

VCC3LGC

—

Internal logic power supply pin

18

BEEP

O

Beep signal output

19

XFLMWE

O

Write enable signal output to the flash memory IC (IC701)

20

XFLMRE

O

Read enable signal output to the flash memory IC (IC701)

21

FLMALE

O

Address latch enable signal output to the flash memory IC (IC701)

22

FLMRB

I

Ready/busy signal input from the flash memory IC (IC701)

23

XFLMWP

O

Write protect signal output to the flash memory IC (IC701)

24 to 30

USBADR0 to 6

O

Address signal output to the USB controller IC (IC8101)

31

XUSBCS

O

Chip select signal output to the USB controller IC (IC8101)

32

XUSBRD

O

Read strob signal output to the USB controller IC (IC8101)

33

XUSBRST

O

Reset signal output to the USB controller IC (IC8101)

34

XUSBLWR

O

Low write strob signal output to the USB controller IC (IC8101)

35

XFLMPWR

O

Power control signal output for flash memory

36

AVSS

—

Power supply pin for analog

37

AVREF

—

Reference power supply pin

38

AVSS

—

Ground pin for analog

39

BATT

I

Battery voltage detection signal input

40

KEYIN0

I

Key 0 A/D input

41

KEYIN1

I

Key 1 A/D input

42

XBATTEN

O

Battery detection control signal output

43 to 45

PC4 to PC6

I

Not used in this set. (Open)

46

LMUTE

O

Mute signal output

47

VSS

—

Ground pin

48

AVCC3IO

—

Power supply pin

49 to 74

SEG0 to SEG25

O

LCD segment signal output to the LCD901

75

DVCC

—

Power supply pin

76

DVSS

—

Ground pin

77 to 82

SEG26 to SEG31

O

LCD segment signal output to the LCD901

83 to 86

COM0 to COM3

O

LCD common signal output to the LCD901

87

MOD2

I

Operation mode signal input

88, 89

MOD1, MOD0

I

Operation mode signal input (Fixed at “L” in this set.)

90

XCPURST

I

CPU external reset signal input to the reset IC (IC704)

91 to 94

LCDV0 to LCDV3

—

LCD reference power supply input pin

95

RX

I

Input/output port (Flash write RX)

96

TX

O

Input/output port (Flash write TX)

97

PO2

O

Not used in this set. (Open)

98

RTCSIN

I

Serial data signal input from the real time clock IC (IC703)

99

RTCSOT

O

Serial data signal output to the real time clock IC (IC703)

100

RTCSCK

O

Serial clock signal output to the real time clock IC (IC703)

101

RTCCS

O

Chip select signal output to the real time clock IC (IC703)

102

XDSPRST

O

Reset signal output to the DSP IC (IC101)

103

WAKEUP

I

Wake up interruption signal input

12

Pin No.

Pin Name

I/O

Pin Description

104

DSPIFACK

I

DSP I/F acknowledge signal input

105

DVCC

—

Power supply pin

106

DVSS

—

Ground pin

107

XTALIN

I

Main oscillator input pin

108

XTAL

O

Main oscillator output pin

109

XINTUSB

I

Interruption request signal input from the USB driver IC (IC8101)

110

XUSBVBUS

I

VBUS detection interruption request signal input from the USB driver IC (IC8101)

111

XRTCINTR

I

Constant cycle interruption signal input from the real time clock IC (IC703)

112

HOLDSW

I

Hold switch signal input (interruption)

113

AMPPWR

O

Power control signal output to the power amp IC (IC110)

114

XMICPWR

O

Power control signal output for microphone

115

GRNLED

O

LED drive signal output to the green LED (D701)

116

REDLED

O

LED drive signal output to the red LED (D701)

117

DSPPWR

O

Power supply circuit control signal output for DSP IC (IC101)

118

DSPIFRW

O

I/F RW signal output to the DSP IC (IC101)

119

DSPSIN

I

Serial data signal input from the DSP IC (IC101)

120

DSPSOT

O

Serial data signal output to the DSP IC (IC101)