Sony ICD-P17 Service Manual ▷ View online
5
ICD-P17
Note : This set can be disassemble according to the following sequence.
SECTION 3
DISASSEMBLY
Note : Follow the disassembly procedure in the numerical order given.
3-1. UPPER LID BLOCK ASSY
3-1.
UPPER LID BLOCK ASSY
(Page 5)
(Page 5)
3-2.
F-SW BOARD,
P-SW BOARD
(Page 6)
P-SW BOARD
(Page 6)
SET
3-3.
MAIN BOARD
(Page 6)
(Page 6)
3-4.
PC BOARD
(Page 7)
(Page 7)
1
B 1.7x10
4
claw
2
B 1.7x7
8
screws 1.7x2.5
9
speaker (SP101)
3
claws
5
claws
6
claw
0
upper lid block assy
case block assy
7
6
ICD-P17
3-2. F-SW BOARD, P-SW BOARD
3-3. MAIN BOARD
2
CN703
3
case block assy
4
F-SW board
5
P-SW board
3
Removal the seven solders.
1
Removal the solder.
3
screw
4
claw
5
claw
case (lower) assy
1
Removal the two solders.
8
MAIN board
7
6
CN801
2
speaker (SP101)
(1.7x3.0)
7
ICD-P17
3-4. PC BOARD
case (lower) assy
2
PC board
3
holder (jack)
1
screw (1.7x3.7)
8
ICD-P17
SECTION 4
TEST MODE
[Setting Method of the Test Mode]
(1) To enter the test mode, turn on the HOLD switch while
pressing the STOP key and MENU key at the same time with
the power on.
the power on.
[Exiting Method of the Test Mode]
Exit the test mode by turning off the power.
[Initial Status of the Test Mode]
When the test mode is set, the LCD display appears as shown
below.
below.
LCD display
P17
/091
[Flow Chart of the Test Mode]
LCD
AUDIO
SLEEP
BEEP
RTC
MENU
COUNT
USB
LED
BATT
KEY
RST
KEY
Initial status of
Test mode.
Set code,LPEC ST,
F/W version display
Test mode.
Set code,LPEC ST,
F/W version display
.
>
.
>
.
>
.
>
.
>
>
.
>
.
.
>
.
>
.
>
.
>
.
>
START
TEST MODE
END
TEST MODE
Turning off the power.
091
t
IC702 version
(Displayed to A or B folder
when version a or b.)
(Displayed to A or B folder
when version a or b.)
P17
t
Set code
[Operation in the Test Mode]
After entering the test mode, you can move within the test menu by
pressing the . / > key. You can move to the submenu by
pressing the x•B key. Then each test mode can be executed.
pressing the . / > key. You can move to the submenu by
pressing the x•B key. Then each test mode can be executed.
1. LCD test
• LCD is tested all light-on and all light-off.
• LCD is tested all light-on and all light-off.
2. Audio test
Perform the through-playback.
• Contents of the submenu
Perform the through-playback.
• Contents of the submenu
DSPLOP: DSP through mode.
• Select the microphone sensitivity with the MIC SENS switch.
H
tLtHtLt……
• MUTE can be set to “ON” or “OFF” with the ERASE key.
• The sound volume can be adjusted with the VOL volume key
• The sound volume can be adjusted with the VOL volume key
during the audio test except the MUTE mode.
• This test operates in accordance with to the JACK detection test.
It displays the current mode, microphone sensitivity and mute
on the LCD display.
on the LCD display.
[Example of LCD display]
DSP through mode/MIC: H/MUTE: OFF
tH/OF/DSPLOP
(SET)
/ .
.
.
/ >
x
• B
x
• B
LCD
LCD
ALL
(SELECT)
START
CHK
END
CHK
LCD
OFF
LCD
ON
STOP
STOP
STOP
STOP
OFF LCD
•
•
•
•
•
•
CHK LCD
ALL LCD
ALL LCD
AUDIO
DSPLOP
(SET)
.
/ >
x
• B
x
• B
(SELECT)
STOP
STOP
H
OF
DSPLOP
Click on the first or last page to see other ICD-P17 service manuals if exist.