DOWNLOAD Sony ICD-BP220 Service Manual ↓ Size: 2.61 MB | Pages: 29 in PDF or view online for FREE

Model
ICD-BP220
Pages
29
Size
2.61 MB
Type
PDF
Document
Service Manual
Brand
Device
Audio
File
icd-bp220.pdf
Date

Sony ICD-BP220 Service Manual ▷ View online

ICD-BP220
Chinese Model
SERVICE MANUAL
IC RECORDER
SPECIFICATIONS
Ver 1.0  2001. 10
Sony Corporation
Personal Audio Company
Published by Sony Engineering Corporation
9-873-359-01
2001J1600-1
© 2001.10
Recording media
Built-in flash memory, Monaural recording
Recording time
SP:  262 minutes, LP: 698 minutes
Frequency response
SP: 250 Hz - 7,300 Hz
LP: 300 Hz - 3,500 Hz
Speaker
approx. 3.2 cm (1 
5
/
16 
 in.) dia.
Power output
300 mW
Input/Output
• Earphone jack (minijack) for 16 - 300 ohms
earphone/headphones
• Microphone jack (minijack, monaural)
Plug in power
Minimum input level 0.6 mV
3 kilohms or lower impedance microphone
• USB connector
Playback speed control
FAST  +30%, SLOW  –15%
Power requirements
Two LR03 (size AAA) alkaline batteries: 3 V DC
Dimensions (w/h/d) (not incl. projecting parts and controls)
44.5 
× 105.3 × 14.0 mm (1 
13
/
16
 
× 4 
1
/
4
 
×  
9
/
16  
in.)
Mass (incl. batteries)
79 g (2.79 oz)
Supplied accessories
Earphone 
× 1
Carrying case 
× 1
Connecting cable 
× 1
“Digital Voice Editor” (CD-ROM) 
× 1
Optional accessories
Electret Condenser Microphone ECM-Z60, ECM-
T15, ECM-T115
Earphone MDR-ED228LP, MDR-E818LP
Connecting cord RK-G64
Your dealer may not handle some of the above listed optional accessories. Please
ask the dealer for detailed information.
Design and specifications are subject to change without notice.
2
ICD-BP220
TABLE OF CONTENTS
1. GENERAL ·································································· 3
2. DISASSEMBLY
2-1. Sub Block Assy, Upper Lid ············································· 4
2-2. F-SW Board ···································································· 4
2-3. Main Board, P-SW Board ··············································· 5
2-4. PC Board ········································································· 5
3. DIAGRAMS
3-1. Block Diagram ································································ 7
3-2. Printed Wiring Board – Main Section (1/2) – ················· 8
3-3. Printed Wiring Board – Main Section (2/2) – ················· 9
3-4. Schematic Diagram – Main Section (1/3) – ·················· 10
3-5. Schematic Diagram – Main Section (2/3) – ·················· 11
3-6. Schematic Diagram – Main Section (3/3) – ·················· 12
3-7. Schematic Diagram – F-SW Section – ························· 13
3-8. Printed Wiring Board – F-SW Section (1/2) – ·············· 14
3-9. Printed Wiring Board – F-SW Section (2/2) – ·············· 15
3-10. Printed Wiring Board – PC Section – ························· 16
3-11. Schematic Diagram – PC Section – ···························· 17
3-12. Printed Wiring Board – P-SW Section – ···················· 18
3-13. Schematic Diagram – P-SW Section – ······················· 19
3-14. IC Block Diagrams ····················································· 20
3-15. IC Pin Function Description ······································· 21
4. EXPLODED VIEWS
4-1. Upper Lid Assy Section ················································ 23
4-2. Main Board Section ······················································ 24
5. ELECTRICAL PARTS LIST ·································· 25
Flexible Circuit Board Repairing
• Keep the temperature of the soldering iron around 270
°C during
repairing.
• Do not touch the soldering iron on the same conductor of the
circuit board (within 3 times).
• Be careful not to apply force on the conductor when soldering or
unsoldering.
Notes on chip component replacement
• Never reuse a disconnected chip component.
• Notice that the minus side of a tantalum capacitor may be dam-
aged by heat.
*
Replacement of IC109 used in this set requires a special tool.
The voltage and waveform of CSP (chip size package) cannot be
measured, because its lead layout is different from that of conven-
tional IC.
Lead layouts
Unleaded solder
Boards requiring use of unleaded solder are printed with the lead-
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size.)
 : LEAD FREE MARK
Unleaded solder has the following characteristics.
• Unleaded solder melts at a temperature about 40
°C higher than
ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350
°C.
Caution: The printed pattern (copper foil) may peel away if the
heated tip is applied for too long, so be careful!
• Strong viscosity
Unleaded solder is more viscous (sticky, less prone to flow) than
ordinary solder so use caution not to let solder bridges occur such
as on IC pins, etc.
• Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.
surface
Lead layout of
conventional IC
CSP (chip size package)
3
ICD-BP220
SECTION 1
GENERAL
This section is extracted from
instruction manual.
1
MIC (built-in microphone)
(12)
2
Display window (64)
3
FOLDER button (12, 16)
4
INDEX/BOOKMARK
button (22, 26)
5
DISPLAY button (39)
6
A-B REPEAT/PRIORITY
button (23, 30)
7
MENU button (10, 32, 35, 40,
41)
8
ERASE button (20)
9
xSTOP button (13, 17)
q;
Speaker
qa
MIC (PLUG IN POWER)
jack (15)
qs
EAR (earphone) jack (14, 17)
qd
OPR (operation) indicator
(12, 17)
qf
zREC (record) /STOP
button (13, 24)
qg
X PAUSE button (13, 17)
qh
.REVIEW/>CUE (fast
backward, review/fast
forward, cue•selection of
menu mode) button  (10, 16,
18, 19, 22, 26, 30, 32, 35, 40,
41)
qj
NxPLAY/STOP
•EXECUTE (play/
stop•enter) button (10, 17,
18, 29, 30, 32, 35, 40, 41)
qk
HOLD switch (38)
ql
VOL (volume) control (17)
w;
USB connector for
connecting to a computer
(48)
qa
qs
qd
qf
qg
qh
qj
qk
ql
w;
q;
9
8
7
6
5
4
3
2
1
Main unit
Rear
wh
wg
wf
wa
ws
wd
wa
PLAY SPEED selector (18)
ws
MIC SENS (microphone
sensitivity) selector (14)
wd
VOR selector (15)
wf
Clip*
wg
Battery compartment (8)
wh
Hook for handstrap (not
supplied)
4
ICD-BP220
SECTION 2
DISASSEMBLY
Note : Follow the disassembly procedure in the numerical order given.
2-1.
SUB BLOCK ASSY, UPPER LID
2-2.
F-SW BOARD
2
3
 F-SW board
1
 Connector (CN703)
Case assy
4
5
 Sub block assy, upper lid
1
 Screw (B1.7 
× 
10)
2
 Screw (B1.7 
×
 7)
3
 Remove two solderings
Case assy
Set
Sub block assy,upper lid
F-SW board
PC board
MAIN board, P-SW board
Note : Disassemble the unit in the order as shown below.
Page of 29
Display

Sony ICD-BP220 Service Manual ▷ Download

  • DOWNLOAD Sony ICD-BP220 Service Manual ↓ Size: 2.61 MB | Pages: 29 in PDF or view online for FREE
  • Here you can View online or download the Service Manual for the Sony ICD-BP220 in PDF for free, which will help you to disassemble, recover, fix and repair Sony ICD-BP220 Audio. Information contained in Sony ICD-BP220 Service Manual (repair manual) includes:
  • Disassembly, troubleshooting, maintenance, adjustment, installation and setup instructions.
  • Schematics, Circuit, Wiring and Block diagrams.
  • Printed wiring boards (PWB) and printed circuit boards (PCB).
  • Exploded View and Parts List.