DOWNLOAD Sony ICD-B200RS Service Manual ↓ Size: 1.01 MB | Pages: 24 in PDF or view online for FREE

Model
ICD-B200RS
Pages
24
Size
1.01 MB
Type
PDF
Document
Service Manual
Brand
Device
Audio
File
icd-b200rs.pdf
Date

Sony ICD-B200RS Service Manual ▷ View online

5
ICD-B200RS
2-2. SWITCH BOARD, MAIN BOARD
2-3. AUDIO BOARD
1
 CN705
2
 SWITCH board
4
 MAIN board 
S701
3
 CN701
5
 claw
6
9
8
7
 claw
 S702
3
 screw
2
 cushion (battery case lid)
1
 battery case lid
0
 AUDIO board 
4
 speaker (2cm)
6
ICD-B200RS
SECTION 3
SERVICE MODE
3-1. Setting the Service Mode
To enter the service mode, use the following procedure:
With the power on, turn the  HOLD  switch on while pressing the
x STOP  key and the  VOLUME–  key.
3-2. Resetting the Service Mode
The service mode is reset by turning the power off (removing the
power cord).
3-3. Initial State of the Service Mode
3-3-2. FlashMemory ID display
The ID of FlashMemory is displayed. This ID represents the
manufacturer code and device code.
The service mode has the initial screen of “Version display”. A
desired test mode under service mode is selected by pressing the
.+  key or  > –  key. Then, the testing operation in the selected
mode is determined by using the  Bx  key.
3-3-1. Version display
The version display is the initial screen in service mode and shows
the set name and the version No.
3-3-3. BadBlock count display
The count of initially faulty blocks for FlashMemory data is
displayed.
(Initial screen)
Version
display
Key Test
Reset Menu
Dsp Loop
Test
Battery
Value
Flash
Memory
ID display
BadBlock
count
display
Lcd
Test
Beep
Test
Set name
Version No 
"1.00"
Device code
Manufacturer code
TOSHIBA
SAMSUNG
Manufacturer code
98
EC
Device code
(Memory Size)
16MB
32MB
73
75
73
75
BadBlock 
count
7
ICD-B200RS
3-3-4. LCD test
The initial screen for LCD test displays the blinking characters
“LCD”. The LCD test mode includes seven different LCD tests.
The LCD test mode is executed by pressing the  Bx  key while the
“LCD”characters are blinking.
Pressing of the  x STOP  key during any LCD test (display) will
return to this initial screen for LCD test. The LCD tests present the
following displays:
1. All LCD segments on
2. All LCD segments off
3. All LCD segments blinking
4. Even segments displayed
5. Odd segments displayed
6. LCD1 segments displayed
7. LCD set characters displayed
1) Segment test
The segment test is intended to check whether Com-Seg Map is
correct or not. When this test mode is selected, the initial screen
displays the blinking characters “SEG”.
The number of segments are 120. The segment test is executed by
pressing the  Bx  key while the “LCD” characters are blinking.
Pressing of the  x STOP  key during any display of the segment
test will return to the initial screen for LCD test. The segment test
includes the following displays:
Initial screen for LCD TEST
All ON
STOP
Character display
Segment
ODD
EVEN
All OFF
All blinking
STOP
This cycle is repeated until 
the 
   
 key is pressed (toggle).
Segment
Initial screen 
for LCD TEST
8
ICD-B200RS
2) MOJI test
The MOJI test is intended to show the character display (characters/
digits). When this test mode is selected, the initial screen displays
the blinking characters “MOJI”. The MOJI test is executed by
pressing the  Bx  key while the “MOJI”characters are blinking.
Pressing of the  x STOP  key during any display of the MOJI test
will return to the initial screen for LCD test. The MOJI test includes
the following displays:
3-3-5. BEEP test
The beep test is intended to sound 2.4 kHz beeps. When this test
mode is selected, the initial screen displays the blinking characters
“BEEP”. The beep test is executed by pressing the  Bx  key while
the “BEEP” characters are blinking. By pressing the  x STOP  key,
the beep sound will stop returning you to the initial screen for beep
test. The beep test includes the following displays:
Initial screen 
for LCD TEST
STOP
This cycle is repeated until 
the 
   
 key is pressed (toggle).
Character display
3-3-6. Battery value
The voltage value of the battery inserted into the set is displayed in
hexadecimal format. The value is invalid when the adapter is inserted.
STOP
Initial screen 
for BEEP TEST
beep 
3-3-7. DSP LOOP test
The DSP loop test has the following flow:
DSP
MIC
MIC AMP
POWER
 AMP
SPEAKER
Note : Incoming voice data from the MIC is outputted to the 
          speaker as it is.
Voice
Voice
VOICE
Voice
Voice
Battery voltage value 
(HEX value)
BATTERY display screen
The initial screen for DSP loop test displays the blinking characters
“DSP”. The DSP loop test is executed by pressing the  Bx  key
while the “DSP” characters are blinking. Pressing of the  x STOP
key during any display of DSP loop test will return you to the initial
screen for DSP loop test.
The volume can be changed by using the VOLUME+  or  VOLUME–
key. The volume value can be set to 0 to 30 levels, but is not displayed
on the screen when changed. The DSP loop test includes the
following displays:
STOP
STOP
STOP
SP MODE
LP MODE
HQ MODE
Initial screen for 
DSP LOOP TEST
Note: The volume value can be set to 0 to 30 levels, 
               but is not displayed on the screen when changed.
Page of 24
Display

Click on the first or last page to see other ICD-B200RS service manuals if exist.