Sony ICD-B17 Service Manual ▷ View online
5
ICD-B17
Note : This set can be disassemble according to the following sequence.
SECTION 3
DISASSEMBLY
Note : Follow the disassembly procedure in the numerical order given.
3-1. UPPER LID ASSY
3-1.
UPPER LID ASSY
(Page 5)
(Page 5)
3-2.
F-SW BOARD,
P-SW BOARD
(Page 6)
P-SW BOARD
(Page 6)
SET
3-3.
MAIN BOARD
(Page 6)
(Page 6)
1
B 1.7x10
4
claw
2
B 1.7x7
7
screws 1.7x2.5
8
speaker (SP101)
3
claws
5
claws
9
upper lid assy
case assy
6
claw
6
ICD-B17
3-2. F-SW BOARD, P-SW BOARD
3-3. MAIN BOARD
2
CN701
3
case assy
5
F-SW board
6
P-SW board
4
Removal the five solders.
1
Removal the solder.
4
claw
5
claw
case assy
1
Removal the two solders.
6
MAIN board
2
speaker (SP101)
3
B 1.7x4
7
ICD-B17
4-1. IC PIN DESCRIPTION
• IC703 µPD780308GC-A66-8EU (MEMORY CONTROL, SYSTEM CONTROL)
Pin No.
Pin Name
I/O
Pin Description
1 – 3
KEY0 – KEY2
I
Key signal input
4
XHOLD
I
Hold switch signal input
5
AMPPOW
O
Power down control signal output to the power amplifier IC (IC103)
6
AVREFON
I
A/D reference voltage input
7
XFMCE
O
Chip enable signal output to the flash memory IC (IC701)
8
VDD0
—
Power supply pin (+3.3 V)
9
AVREF
—
A/D reference voltage
10
XFMWE
O
Write enable signal output to the flash memory IC (IC701)
11
XFMALE
O
ALE signal output to the flash memory IC (IC701)
12
VSS1
—
Ground pin
13
XFMR/B
I
Ready/Busy signal input from the flash memory IC (IC701)
14
XFMCLE
O
CLE signal output to the flash memory IC (IC701)
15, 16
NC
O
Not used. (Open)
17
XFMRE
O
Read enable signal output to the flash memory IC (IC701)
18
XFMSE
O
SE signal output to the flash memory IC (IC701)
19
XFMWP
O
WP signal output to the flash memory IC (IC701)
20
CLKOUT
O
Not used in this set. (Open)
21
BEEP
O
Beep signal output (2.4 kHz)
22
LIGHT
O
LCD back light control output Not used in this set. (Open)
23 – 26
COM0 – COM3
O
LCD common signal output
27
BIAS
O
Connect to VDD. (LCD bias)
28 – 30
VLC0 – VLC2
—
LCD drive power supply pin
31
VSS0
—
Ground pin
32 – 61
S0 – S29
O
LCD segment signal output
62
NC
I
Not used. (Open)
63
NC
O
Not used. (Open)
64
XTEST
I
Test pin
65
DSPPOW
O
Digital signal processor registor control I/F enable signal output
66
LEDREC
O
OPR (REC) LED (D701: red) ON/OFF signal output
67
LEDPB
O
OPR (PLAY) LED (D701: green) ON/OFF signal output
68
RTCCE
O
Real time clock chip enable signal output
69
XDSPIFRQ
O
I/F request signal output to the DSP IC (IC101)
70
DSPIFRW
O
I/F data read/write signal output to the DSP IC (IC101)
71
XDSPRST
O
Reset signal output to the A/D, D/A converter, DSP IC (IC101)
72
SI0
I
I/F data signal input to the DSP IC (IC101)
73
SO0
O
I/F data signal output to the DSP IC (IC101)
74
SCK0
O
I/F signal clock output to the DSP IC (IC101)
75
RTCDI
I
Real time clock data signal input
76
RTCDO
O
Real time clock data and digital signal processor registor control data output
77
RTCCLK
O
Real time clock I/F data and digital signal processor registor control clock output
78
IC
—
Connect to ground.
79
X2
O
System clock output (5 MHz)
80
X1
I
System clock input (5 MHz)
81
VDD1
—
Power supply pin
82
XT1
—
Sub clock input (32.768 kHz)
83
XT2
—
Not used in this set. (Open)
84
XRESET
I
Reset signal input
85
NC
—
Not used. (Open)
SECTION 4
DIAGRAMS
8
ICD-B17
Pin No.
Pin Name
I/O
Pin Description
86
WAKEUP
I
WAKE UP signal input
87
RTCINT
I
Real time clock (2 Hz) signal input
88
FLMPOW
O
Flash memory power ON/OFF signal output
89
DSPIFACK
I
I/F acknowledge signal input to the DSP IC (IC101)
90
LMUTE
O
Line mute ON/OFF signal output
91 – 98
FMI01 – FMI07
I/O
Data bus signal input/output
99
AVSS
—
Ground pin
100
BATT
I
Power supply voltage detection signal input
Click on the first or last page to see other ICD-B17 service manuals if exist.