Sony HT-XT1 Service Manual ▷ View online
HT-XT1
5
MODEL IDENTIFICATION
Distinguish by model number label stuck on the rear side of a main unit.
Distinguish by model number label stuck on the rear side of a main unit.
Note: The printed contents of following fi gure model number label may be different from the model number label of a main unit.
– Rear view –
US and Canadian models
MODEL NUMBER LABEL
4-487-998-0
[] UC2
UK model
4-488-000-0
[] CEK
Singapore model
4-528-595-0
[] SP1
Australian model
4-488-002-0
[] AU1
AEP model
4-487-999-0
[] CEL
Ver. 1.1
HT-XT1
6
SECTION 2
DISASSEMBLY
•
This set can be disassembled in the order shown below.
2-1. DISASSEMBLY FLOW
SET
2-2. GLASS
ASSY
(Page
7)
2-18. LOUDSPEAKER (10 cm) (SUBWOOFER) (SP3, SP4)
(Page
(Page
20)
2-7. LOUDSPEAKER (3.5 × 8 cm)
(FRONT) (SP1, SP2)
(Page
11)
2-8. LEG (LEFT, RIGHT, REAR) ASSY
(Page
(Page
12)
2-3. NFC MODULE (NFC1)
(Page
(Page
8)
2-4. TS
BOARD
(Page
8)
2-5. GRILLE
ASSY
(Page
9)
2-6. DISPLAY
BOARD
(Page
10)
2-9. PANEL (L, R) ASSY
(Page
(Page
12)
2-11. AMP ASSY
(Page
(Page
14)
2-13. POWER CORD (AC1)
(Page
(Page
16)
2-14. HDMI BOARD
(Page
(Page
17)
2-16. POWER BOARD
(Page
(Page
18)
2-15. IO BOARD
(Page
(Page
17)
2-17. MAIN BOARD
(Page
(Page
19)
2-10. BLUETOOTH MODULE (BT1)
(Page
(Page
13)
2-12. HOW TO INSTALL AMP ASSY
(Page
(Page
15)
• JIG
When disassembling the unit, use the following jig (for speaker
When disassembling the unit, use the following jig (for speaker
removal).
Part
No.
Description
J-2501-238-A
JIG FOR SPEAKER REMOVAL
HT-XT1
7
Note: Follow the disassembly procedure in the numerical order given.
2-2. GLASS
ASSY
Note 1: As the part is made of glass, exercise extreme caution when handling it.
Note 2: Cushion (glass) with double-sided tape was added to US, Canadian, AEP, UK and Australian models from the midway of production.
Note 2: Cushion (glass) with double-sided tape was added to US, Canadian, AEP, UK and Australian models from the midway of production.
(Cushion (glass) with double-sided tape has been used for Singapore model since the beginning of production.)
Accordingly, the glass assy removal process has changed.
Please refer to technical news separately issued.
1 Lift the glass assy in the direction
of the arrow.
2 shaft
2 two shafts
2 shaft
1 Lift the glass assy in the direction
of the arrow.
3 glass assy
2 two shafts
Ver. 1.1
HT-XT1
8
2-3. NFC MODULE (NFC1)
2-4. TS BOARD
colored line
colored line
Insert is straight to the interior.
Insert is incline
flexible flat
cable
cable
flexible flat
cable
cable
connector
connector
Note: When installing the flexible flat cable, ensure that
the colored line is not slanted after insertion.
1 Peel off the NFC module block.
2 flexible flat cable
(FFC5)
3 NFC cushion
3 NFC cushion
4 NFC module
(NFC1)
,QVWDOODWLRQGLUHFWLRQIRUWKHIOH[LEOHIODWFDEOH
flexible flat cable (FFC5)
terminal face
NFC module (NFC1)
OK
NG
4 TS board
3 touch cushion
3 touch cushion
2 connector
(CN701)
1 Peel off the TS board block.
3DVWLQJSRVLWLRQRI76ERDUG
guide line
TS board
Click on the first or last page to see other HT-XT1 service manuals if exist.